BirdBlocker BB200 User manual

EN Installation manual
BirdBlocker
BB200
WWW.BIRDBLOCKER.EU







 



3Installation manual
NL Installation manual
BirdBlocker BB200
Read the manual carefully before installing the
BB200. Follow each step in the manual carefully.
Keep the manual for future use.
You are responsible for the correct installation
and use of the BB200 and the solar panels.
Always follow the applicable safety regulations
and use the correct safety devices during
installation on the roof. BirdBlocker B.V. is not
responsible for the installation and correct use.
BirdBlocker works best as a preventive measure
to prevent nuisance from birds. DO NOT install
the BirdBlocker during the breeding period.
The birds will do their utmost to get under the
solar panels because of their nesting urge. In
several countries it is even punishable by law to
disturb nests during this breeding period.
The BB200 is intended for use with solar panels


Then you can not use the BB200.
In the package
· BirdBlocker strips
· BirdBlocker clips
· Cable Ties
Supplies
· Strong scissors
· Measuring tape

4BirdBlocker BB200
! Determine the number of outer corners (A) and inner corners (B) of your solar panel.
A
B
" Measure the maximum distance from the edge of the panel to the roof surface (X).
X
B:
A:
X:

5Installation manual
# Clip test
Make sure the BirdBlocker logo is not visible from below. Try moving the clip from left to right.

panel. You can’t use this one anymore.
$ The correct length of the BirdBlocker needles is X + 2 cm. Cut the BirdBlocker to the correct
length. See Figure 2.
X + 2cm

6BirdBlocker BB200
% First prepare the BirdBlocker strips for the outer corners (number of outer corners A).
Cut a triangle from the BirdBlocker edge and fold the BirdBlocker strip inwards to form a corner.
&B).
Cut the top of the BirdBlocker edge and fold the BirdBlocker strip outwards.

7Installation manual
' Slide a clip onto the BirdBlocker where there is a marking arrow. Make sure the BirdBlocker logo is
visible on the outside.
( Measure how much length of BirdBlocker strip you need from one corner to the other.
Connect strips with a clip. Use a minimum of 2 clips per small piece.

8BirdBlocker BB200
)
Make sure that the space under the solar panel is nicely enclosed by the BirdBlocker.
*

9Installation manual
+
Then cut the needles shorter so that they just touch the roof surface.
, Check that the BirdBlocker covers all around and that there are no openings for a bird to pass
through.

10 BirdBlocker BB200
- Connect the loose strips together with cable ties.
. Cut the ends of the cable ties. Congratulations! Your solar panels are protected with BirdBlocker.

11Installation manual
Disclaimer
Always follow the BirdBlocker installation
instructions. The installation of the BirdBlocker

with experience in installing PV systems on
roofs. The suitability for the intended use of his
solar system is checked by the owner and user
himself. BirdBlocker is not 100% protection
against the nesting of birds or other animals


hinders birds and other animals in accessing the
system.
The installer is responsible not only for the

the solar system on and to which he mounts the
system. The installation instructions do not
release the executing company from the
obligation to clarify the possible uses and
application of our products in connection with
the other materials and products used on the
individual object in advance. If technical details

release the company carrying out the work from
the obligation to check the individual case and
clarify the correct technical facts beforehand.
The specialist company responsible for the
installation must ensure prior to installation that
the installation is carried out strictly in



regulations of the relevant authorities. Every
person who installs the BirdBlocker is obliged

regulations for a professionally correct planning
and installation and to comply with them during
installation. This also includes obtaining the
current status of the rules and regulations.



advance if necessary.

documents are intended to clarify individual
details and are only to be considered as
recommended instructions. BirdBlocker and
wholesaler do not assume any responsibility for



BirdBlocker B.V.
Hooipolderweg 20
2635 CZ Den Hoorn
T [phone]
[e-mail]
[e-mail]
www.birdblocker.eu
