BIRDIE VA00027 User manual

User Manual.
English (EN)

Welcome to the ock! We hope your little ones
love their new ride. Don’t forget to share in-ight
photos by tagging @Bird on Instagram.
#BirdieLife
It’s Birdie time.

3
T-BAR
1
FOOTBOARD
1
Birdie is partially assembled already, so you’ll
only need to do a few things to get your kiddo
ying. Check out the following diagram to
make sure you have all the materials required
for assembly.
GET TO KNOW BIRDIE

T-BAR
FOOTBOARD
FOOT BRAKE
NECK
T-BAR BUTTON
ADJUSTMENT HOLES
T-BAR LOCK

5
Position the T-bar above the hole on the
footbard. Make sure to align the T-bar latch
with the notch in the hole. Depress the latch
and slide the T-bar into the hole. You should
hear a click when the T-bar locks into place.
Conrm the T-bar is secure by ipping the
Birdie over and check that the latch is visible
underneath the footboard hole.
Before allowing your child to ride, make sure
the neck, wheels, and frame of the Birdie have
no obvious signs of damage and all screws are
tight.
ASSEMBLY
FOOTBOARD
HOLE
L ATC H
T-BAR
L ATC H

T-BAR LOCK
T-BAR
BUTTON
TOP
ADJUSTMENT
HOLE
ADJUSTING HEIGHT
Twist the T-bar lock counter-clockwise. Then
press the T-bar button, move the handlebar to
desired height, and twist the lock clockwise
until tight. Make sure the height of the handlebar
is at or below the top adjustment hole.

7
L ATC H
REMOVING HANDLEBAR
Flip the Birdie over so the bottom of the
footboard is visible. Depress the latch near the
footboard hole, then pull the T-bar to remove.
FOOTBOARD
HOLE
L ATC H
T-BAR

MAINTENANCE
The wheels should be checked regularly with
the screw in the wheel tightened if loose.
To tighten the wheels, use a small at blade
screwdriver to remove the screw covers.
Use a 5 mm hex tool to tighten the screw in the
wheel.
Please note, for added safety, the front left
wheel of the Birdie uses a left-handed screw
that tightens in the counterclockwise direction.
The front right and rear wheel use regular
screws that tighten in the clockwise direction.
When complete, replace the screw covers.
SCREW
COVER

9
• Appropriate for children ages 3-8 with a maximum
weight of 50 kg (110 lb). Not suitable for children under
three years.
• Adult supervision required.
• Check and secure all fasteners before every ride.
• Any modications to Birdie will result in warranty
expiration.
• Metal parts may corrode over time, especially if
exposed to moisture outside.
• Contains small parts while unassembled, which may
present a choking hazard; adult assembly required.
• Protective equipment must be worn when riding. This
includes a helmet, shoes with rubber soles, and wrist,
elbow, and knee pads.
• Help your child feel comfortable by practicing rst to
gain control of the Birdie. Always ride with caution to
avoid falls or collisions.
• Ride on smooth, paved surfaces away from motor
vehicles. Avoid sharp bumps, drainage grates, and
sudden surface changes. The Birdie may suddenly
stop.
• Avoid excessive speed associated with downhill rides.
Ensure your child does not ride down any steep hills or
exceed speeds of 4.8 km/h (3 mph).
• Avoid roads, paths, or places with motor vehicle trafc.
Obey all local trafc and scooter riding laws and
regulations.
• Watch out for pedestrians.
• Avoid streets and surfaces with water, sand, gravel,
dirt, leaves, and other debris. Wet weather impairs
traction, braking, and visibility.
• The Birdie may only be used by one child alone.
• Never allow your child to ride at night.
• Keep weather and terrain in mind. Do not ride on
sandy, rough, icy, wet, or uneven surfaces.
• Replace worn or broken parts immediately.
• Brake will get hot from continuous use. Do not touch
after braking.
• Adults must conduct the initial adjustment procedures
to unfold the Birdie, adjust handlebar and steering to
height.
RIDE SAFELY INSTRUCTIONS AND WARNINGS

Birdie Model No. VA00027 / VA00028 / VA00029
Questions? We’ve got answers.
Contact Bird via app or
email [e-mail]
Bird Rides Europe B.V.,
Rokin 92, 1012 KZ,
Amsterdam, Netherlands www.bird.co
This product conforms to the following harmonised standards: EN 71-1: Safety of toys. Mechanical and physical properties.
EN 71-2: Safety of toys. Flammability. | EN 71-3: Safety of toys. Migration of certain elements.