Equipmed Freeroam ii User manual

Colours may vary

Mobility Scooter – FreeRoam II

User Manual

[Revision 1.0 August 2019]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND

MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description and packaging.

THE BATTERY MAY HAVE SOME CHARGE ON ARRIVAL, IT IS IMPORTANT

HOWEVER THAT THE BATTERY IS CHARGED PRIOR TO USE.

Mobility Scooter – FreeRoam II

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

•Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

•Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

•Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

•Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

•Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

•This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

•Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

•Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

•The equipment is designed for domestic

use only.

•Handle the equipment safely and carefully.

•Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

•Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

•Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

•Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

•The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and care,

see Equipment Safety.

Mobility Scooter – FreeRoam II

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

•Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and safety

codes.

•Wherever possible, use a residual current

device (RCD).

•High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

•Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

•Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift, move or

carry equipment.

•Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

•Do NOT attempt any maintenance or repair

work not described in this manual.

•After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

•Do NOT adjust while the equipment is

running.

•Perform service related activities in suitable

conditions, such as a workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Mobility Scooter Safety

DO NOT OPERATE THE SCOOTER BEFORE READING AND UNDERSTANDING THIS INSTRUCTION MANUAL.

IF YOU ARE IN DOUBT ABOUT THE MEANING OF THESE INSTRUCTIONS, OR ANY OF THE CAUTIONS AND WARNINGS, PLEASE

CONSULT YOUR HEALTHCARE PROFESSIONAL, DEALER OR RELEVANT TECHNICAL PERSONNEL.

FAILURE TO FULLY UNDERSTAND THE SCOOTER OPERATION MAY RESULT IN ANUNEXPECTED RESPONSE FROM THE EQUIPMENT

WHICH CAN IN TURN LEAD TO POSSIBLE INJURY OR DAMAGE.

Warning and Caution notices used in this manual, apply to hazards and unsafe practices that could result in personal injury or damage to property.

We supply an extensive range of mobility scooters to meet the varying needs of individual users. It is the responsibility of the individual user and

their healthcare advisor qualified in making such choices, to decide which scooter is suitable for the user’s intended purpose.

With regards to restraints, seat positioning straps, posture correction or other positional aids and accessories, it is the obligation of the qualified

healthcare professional in conjunction with the dealer to ensure the suitability of such equipment for the safe operation of the scooter.

Serious injury can occur in the event of a fall from a mobility scooter. We DO NOT RECOMMEND that a scooter user is transported in any type of

vehicle when seated in the scooter.

At this time, there are no approved Tie-down Systems for the transportation of a user in ANY moving vehicle whilst seated in a scooter. It is our

opinion that users of mobility scooters should be transferred into the appropriate vehicle seating system and use should be made of the restraints

available to the auto industry.

Intended Use: This mobility scooter would be used by disabled, sick or old person.

Personal & Operational Guidelines

•Drive profiles should only be adjusted by healthcare professionals and approved agents/dealers, who are totally conversant with the process.

They must also fully understand the user’s capabilities and the user’s ability to operate the scooter safely.

•Incorrect settings may cause injury or damage to the user, bystanders, the scooter and/or nearby property.

•To determine personal mobility limitations, practice combinations of bending, reaching, mount and dismount techniques, whilst in the presence of

a healthcare professional. Practice the above techniques BEFORE actively using the scooter.

•For users with balance problems, practice the above techniques with the aid of an assistant, in the presence of a healthcare professional.

•DO NOT attempt to pick up objects that cause you to shift your weight in the seat or require you to bend excessively in any direction. Such action

may result in the scooter tipping over, or in injury to the person or both.

•DO NOT use an escalator to move the mobility scooter between floors as serious bodily injury could arise from such actions.

•DO NOT drive on the road, dual carriageways or motorways.

•DO NOT drive up, down or across inclines that have water, ice, oil or any other slippery substance on the surface. Failure to note the above

conditions could cause loss of control.

•DO NOT attempt to drive over kerbs or obstacles in excess of 45mm. Disregarding this warning could cause the mobility scooter to tip resulting in

possible bodily harm.

•DO NOT make sharp turns in forward or reverse at high speeds.

•DO NOT lift the mobility scooter by its Tiller, Seat, Body Panels or by any detachable assemblies. Always disassemble the scooter into its

stowable parts and then lift each assembly one at a time.

•DO NOT carry passengers on your scooter.

•DO NOT attempt to tow another vehicle.

•DO NOT operate the mobility scooter without first checking that it is safe to do so. Always be aware of your surroundings.

Mobility Scooter – FreeRoam II

•DO NOT attempt to use your mobility scooter without first checking that all wiring harnesses are connected and all detachable parts/assemblies

are correctly aligned and firmly fixed in place.

•DO NOT use your mobility scooter without the anti-tipper wheels attached.

•DO NOT attempt to fit parts, accessories or adapters that are not authorized.

•DO NOT mount or dismount your mobility scooter without first withdrawing the ignition key. This will ensure that the power is off, and the scooter

cannot move unexpectedly.

•DO NOT leave the ignition key in your scooter whilst it is unattended. Children or inexperienced people may attempt to drive your scooter which

may result in damage or personal injury.

•DO NOT connect any medical device, such as a ventilator, life support machine etc. to the scooter’s electrical system. Failure of the equipment

may result from such connections.

•DO NOT operate your mobility scooter whilst under the influence of alcohol, drugs or prescription medication that may impair judgement.

•DO NOT operate your mobility scooter if you feel acutely unwell.

•DO NOT operate your mobility scooter if your vision is seriously impaired.

•If you have any doubts about medical conditions, health problems or treatments that may affect your ability to operate the mobility

scooter safely, please consult your healthcare professional.

•We specifically disclaim responsibility to all personal injury and property damage that may occur during use which does not comply

with the relevant national or local statutes.

•Do not attempt to operate your scooter whilst standing next to it.

•Always ensure that you are able to operate all the controls from a seated position, that the rear view mirror (if fitted) is set correctly and that the

seat is securely locked into place.

•Attention: Switch on the scooter lights (if fitted) to make yourself visible when there are low levels of light, day or night.

•The rear body panel (where fitted) is designed to cover the Drive Assembly, Wiring Harness and Electrical Connectors.

•DO NOT stand on any of the body panels, only the footboard.

•DO NOT stand on the scooter seat.

•DO NOT attempt to transfer into or out of the scooter seat without first checking that it is LOCKED into position. Attempting unsafe transfers can

result in bodily injury and/or damage.

•DO NOT drive your scooter if the seat is not LOCKED in the FORWARD position. The seat must be secured in the FORWARD facing position

BEFORE and DURING operation of the scooter. Attempting to operate the scooter with the seat not secured in the front facing position, could

result in damage and/or bodily injury.

•DO NOT operate the scooter without ensuring that the Tiller is properly adjusted and secured. After making any adjustment to the Tiller position

you must check that the Tiller is locked and secured into position BEFORE driving. To check, gently push and pull the Tiller to make sure it is

secured. An unsecured Tiller could result in damage and/or bodily injury.

•DO NOT attempt to climb, ascend, or descend ramps greater than 10 degrees, or transverse slopes with a gradient greater than 10 degrees.

•DO NOT attempt to reverse down slopes in excess of 8 degrees. When negotiating ramps or inclines, if the throttle lever is released a roll back

will occur.

•In FORWARD or REVERSE motion, the scooter will ROLLBACK approximately 30cms. (1ft), before the brake engages.

•Check that all electrical connections are secure before using your scooter.

•DO NOT under any circumstances, disconnect, cut, extend or otherwise modify ANY of the wiring harnesses installed within or connected to your

mobility scooter.

•DO NOT under any circumstances, disconnect, cut, extend or otherwise modify ANY of the wiring harnesses installed within or connected to your

mobility scooter battery charger.

•It is important that your mobility scooter battery charger is connected to a properly installed electrical socket with an earthed outlet.

•Failure to comply with the above requirements could result in a possible SHOCK HAZARD.

•DO NOT use any batteries that are not DEEP CYCLE GEL, AGM or SEALED LEAD-ACID type. Other types of batteries are NOT SUITABLE.

•Please read battery/battery charger information before installation.

•This scooter has been tested to ISO 7176 Part 9 “Climatic Tests for Electric Wheelchairs.” The test provides the scooter user or their attendant,

sufficient time to remove the mobility scooter from a rainstorm, while retaining normal operation of the mobility scooter.

•DO NOT operate your mobility scooter during an electrical storm.

•DO NOT leave your mobility scooter in a rainstorm of any kind.

•DO NOT use your mobility scooter in a shower or leave it in a damp bathroom or sauna.

•DO NOT leave your mobility scooter in a damp area for any length of time.

•DO NOT Jet wash, hose down, or use an automated car-wash on your mobility scooter.

•Direct exposure to rain, sea spray or moisture could cause the mobility scooter to malfunction electrically and mechanically and may cause

rusting.

Mobility Scooter – FreeRoam II

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Mobility Scooter – FreeRoam II

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Mobility Scooter – FreeRoam II

Table of Contents

Safety ......................................................................................................................................................... 2

Safety Symbols...........................................................................................................................................................5

Parts Identification .................................................................................................................................... 9

Quick Start Guide .................................................................................................................................... 10

Assembly ..................................................................................................................................................................10

Battery Charging.......................................................................................................................................................10

Typical Use ...............................................................................................................................................................10

Control Functions......................................................................................................................................................10

Transporting..............................................................................................................................................................10

Operation ................................................................................................................................................. 12

Getting On Your Scooter ..........................................................................................................................................12

Getting Off Your Scooter ..........................................................................................................................................12

Control Panel ............................................................................................................................................................13

Hand Controls ....................................................................................................................................................13

The Pre-set Speed Knob....................................................................................................................................13

The Battery Gauge ...................................................................................................................................................13

Operating the Lights .................................................................................................................................................14

Tiller Control Functions.............................................................................................................................................14

Throttle Lever .....................................................................................................................................................14

Horn Button ........................................................................................................................................................14

Key Switch..........................................................................................................................................................15

Off Board Charging Socket ................................................................................................................................15

Freewheel Mechanism..............................................................................................................................................16

Seat Removal and Adjustment .................................................................................................................................16

Removing the Seat.............................................................................................................................................16

Seat Adjustment.................................................................................................................................................17

Armrest Adjustment............................................................................................................................................17

Tiller, Battery and Charging ......................................................................................................................................18

Tiller Adjustment ................................................................................................................................................18

Battery Removal.................................................................................................................................................18

Battery Replacement..........................................................................................................................................18

Off-Board Battery Charger .................................................................................................................................18

Fuses..................................................................................................................................................................19

Guidance for Safe Operation and Use .....................................................................................................................20

Basic Driving ......................................................................................................................................................20

Hill Climbing .......................................................................................................................................................20

Traveling Across Slopes ....................................................................................................................................21

Braking ...............................................................................................................................................................21

Emergency Braking............................................................................................................................................21

Mobility Scooter – FreeRoam II

Switching Off ......................................................................................................................................................21

Usage on Footpaths...........................................................................................................................................21

Crossing Roads..................................................................................................................................................22

Turning corners ..................................................................................................................................................22

Use of Mobile Phones ........................................................................................................................................22

Tyres ..................................................................................................................................................................22

Emergency Braking............................................................................................................................................22

Freewheel Mechanism .......................................................................................................................................22

Battery and Charging Information.......................................................................................................... 23

General Information ..................................................................................................................................................23

Batteries....................................................................................................................................................................23

Maintenance Free.....................................................................................................................................................23

Battery Care..............................................................................................................................................................23

Vehicle Range ..........................................................................................................................................................24

Lead-Acid Battery Care and Maintenance ............................................................................................. 25

Top 3 Battery Care Requirements............................................................................................................................25

Maintenance............................................................................................................................................. 26

Maintenance Schedule .............................................................................................................................................26

Transportation ......................................................................................................................................... 28

Environment Conditions ...........................................................................................................................................28

Troubleshooting ...................................................................................................................................... 29

Specifications .......................................................................................................................................... 31

Mobility Scooter – FreeRoam II

Parts Identification

No. Name

1

Control panel

2

Basket

3 Folding

4 Lights

5 Tyres

6 Batteries

7

Freewheel lever

8

Seating

9

Width-adjustable armrests

1

2

3

4

5

6

7

9

8

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Quick Start Guide

Assembly

1. When lifting always keep the back straight, bend the knees and use the lifting handles provided.

2. Ensure your freewheel mechanism is fully engaged, so your scooter can not move while assembling.

3. Set the tiller by rotating the Tiller folding knob while moving the tiller upwards. Remove the basket from the

footboard and place on the bracket located on the front of the tiller.

4. Lift the seat onto the seat post and press down to ensure it is fully engaged.

Battery Charging

The battery MUST be charged for 12 hours before first use. Do not be tempted to use the scooter unless the

battery has been fully charged as failure to do this will result in battery damage. Connect the battery charger to

the mains supply and the charging socket located on the battery pack. Switch on the mains supply and then

switch on the battery charger.

•RED light = Power On.

•YELLOW Light = Charging.

•GREEN Light = Charge Complete.

Charge the scooter overnight after each use to maintain battery condition.

Typical Use

Designed for use on footpaths, for crossing roads and shopping. It should not be driven through mud, water,

snow, sand, loose gravel, long grass or any other unsound surfaces.

When using your mobility scooter, always follow the same road rules that apply to pedestrians. Ride on

the footpath, preferably at walking speed, which is 2–3 kilometres per hour. You should also cross the

road at safe places, such as traffic lights with pedestrian signals and at pedestrian crossings.

Control Functions

Your scooter is equipped with the following features that can be found on the tiller fascia panel:

•On/ Off Switch, Battery Gauge, Speed Control, head Light, Horn and Directional Control Levers.

If you have previously used or owned a scooter before you MUST still read this User Manual carefully to fully

understand the controls and safety warnings.

Transporting

Your scooter may be disassembled quickly and simply for transportation:

1. Lift off the front basket.

2. Remove the seat, leaving the seat stem in position.

3. Place the basket on the floor mat appropriately.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

4. Lower the tiller, using the folding knob, to its lowest setting locking in the basket. Make sure that there is at

least 30mm between Tiller and battery pack.

5. using the lifting handles provided carefully lift the scooter safely and securely into the luggage compartment

of the vehicle.

TIP: Using the front bumper and rear lifting handle provided carefully lift the scooter. To reassemble the scooter

reverses the sequence above.

IMPORTANT: When reassembling the scooter, remember to insert the battery locking pin, because failure to do

so may result in the batteries disengaging during use. Always secure your scooter parts before transportation.

Remember to engage the drive unit by pushing the freewheel lever forwards to stop the scooter from moving.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Operation

Getting On Your Scooter

1. Ensure that the key switch is turned to the off position (Image 1).

2. Push forward the seat swivel lever located under the seat on the right-hand side and rotate the seat to face

you (Image 2).

3. Put the armrests into the fully down position and use them to steady yourself as you gently lower yourself

into the seat (Image 3).

4. Push forward the seat swivel lever and gently swivel the seat to face forward (Image 4).

5. Ensure that both feet are placed firmly on the floorboard of the scooter and the seat is secure (Image 5).

Image 1

Image 2

Image 3

Image 4

Image 5

Getting Off Your Scooter

1. Bring your scooter to a stop and turn the key switch to OFF.

2. Push forward the seat swivel lever located under the seat on the right-hand side and rotate the seat 90

degrees to Exit (Image 2).

3. Put BOTH feet on the ground and gently leave the seat using the arm rests to assist you out of the chair

(Image 3).

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Control Panel

Hand Controls

All of the drive controls for the scooter are to be found on the Tiller Control Box.

The Pre-set Speed Knob

Turning this knob to the left, reduces your available maximum speed. Turning it to the right, increases the

available maximum speed.

The Battery Gauge

•This gives an approximation of battery charge and is illuminated for clarity.

•The gauge is “RED” empty, to “YELLOW” charge required, to “GREEN” charged.

•As the scooter moves over differing terrain, the Battery Gauge will dip up and down, this is normal. For a

more accurate indication, stop the scooter and note the reading. In cold, damp weather the gauge will dip

more often as the capacity and efficiency of all batteries drops in such conditions.

TIP: If your battery gauge has gone into the “RED” section you can increase your remaining range by reducing

your maximum speed. Remember you MUST charge your battery overnight as soon as you can to prevent

battery damage.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Operating the Lights

The lights are operated by pressing the blue button on the front fascia panel. Press the button once to illuminate

the lights, press the button again to switch the lights off. Switch the lights on to make yourself more visible in low

levels of light, day or night.

Tiller Control Functions

Throttle Lever

The throttle lever offers finger-tip control of your scooter.

It controls the speed as well as forward and reverse motion. To move the scooter in a FORWARD motion, PULL

the lever with the RIGHT HAND or PUSH the lever with the LEFT THUMB (Image 1).

To move the scooter in a REVERSE motion, PULL the lever with the LEFT HAND or PUSH the lever with the

RIGHT THUMB. The lever will return by itself when released and the scooter will slow to a stop (Image 2).

The more you move the lever, the more your speed increases up to its pre-set maximum. It is possible to

operate your scooter using one side of the throttle lever. To do this you must PUSH and PULL on the chosen

side of the throttle lever.

Image 1

Image 2

Image 3

Horn Button

Pressing the horn button operates an audible warning sound. Use this function to warn pedestrians of your

presence when necessary (Image 3).

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Key Switch

Image 4

Image 5

Image 6

The key switch switches the scooter ON and OFF. Please note that the key cannot be removed when it is in the

ON position (Image 4).

Make sure that this switch is in the OFF position BEFORE Getting on or off the scooter. Remove the key to

make sure the scooter is OFF (Image 5). Turning the key to OFF whilst driving will cause the scooter to stop

very abruptly. This is not recommended except in emergency stop, as continual use of this function could result

in damage to the scooter.

Off Board Charging Socket

The socket to connect the off-board charger is located on the battery pack (Image 6).

1. To use the socket, swivel the plastic cover to the left or right to reveal the socket connections. The charger

output plug can now be connected ready to accept charge current from the battery charger.

2. After use, ensure that the plastic swivel cover is rotated back into place. This action helps prevent water from

entering the socket connections.

WARNING: Do not attempt to charge your scooter outdoors or in damp/wet conditions.

Failure to comply with this instruction may lead to a shock / fire hazard.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Freewheel Mechanism

A freewheel device disengages the power drive to allow manual operation (i.e. the scooter can be pushed at a

walking pace). This safety function can prevent your scooter from being driven by someone illegally when

parking. By pushing BACKWARD, the lever that is located on the right hand side of the scooter rear panel can

engage the motor for you to drive (Image 8).

Image 8

WARNING: Use extreme caution in the freewheel mode especially on slopes/inclines.

Letting go of your scooter whilst it is in freewheel, can cause the scooter to roll

unexpectedly. ALWAYS re-engage the freewheel device after use, failure to do so may result in injury.

Seat Removal and Adjustment

Removing the Seat

Please note that these instructions are to be used as a guide only.

1. Lift armrests upwards for ease of access (Image 1).

2. Stand behind the seat and fold the backrest down (Image 2).

3. Grasp the seat base and keeping a firm grip, lift the seat vertically, keeping your back straight. Bend knees if

required (Image 3).

4. Place seat at desired location for stowage, keeping back posture straight at all times, bend knees where

required (Image 4).

Note: Exercise caution when lifting the seat.

Image 1

Image 2

Image 3

Image 4

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Seat Adjustment

1. To adjust seat height, remove the seat as described (Image 5).

2. Move the seat post to the new position and refit the seat pin.

3. Refit the seat (Image 6).

Image 5

Image 6

Armrest Adjustment

1. Pull the lock-pin out from the seat base (Image 7).

2. Loose the adjustable bolt (Image 8).

3. Moving the armrests to the desired position and re-tightening the thumbwheel knobs to adjust the width of

the armrest.

Image 7

Image 8

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

Tiller, Battery and Charging

Tiller Adjustment

The scooter features an infinitely adjustable tiller which allows you to lock the tiller in the most comfortable

driving position. This feature also lets you fold the tiller down fully, for transportation and stowage.

The folding knob is located on the bottom of the tiller.

1. Support the tiller with your left hand.

2. Rotate the folding knob anticlockwise to release the tiller (Images 1 & 2).

3. Move the tiller to the desired location.

4. Rotate the folding knob clockwise to lock the tiller (Image 2).

Image 1

Image 2

Image 3

Battery Removal

It is important to remove the seat and seat post first to allow better access to the batteries.

1. Lift battery vertically out of its battery tray using the handle provided (Image 4).

2. Remember to keep the knees bent and the back straight.

Battery Replacement

To replace the batteries, reverse the sequence above

Important: Remember to keep the knees bent and the back straight.

When reassembling the scooter, remember to insert the locking pin, because failure to do so may result in the

batteries disengaging during use. Ensure the battery wells are free from dirt and grit - this will affect the

performance of the battery contacts.

Off-Board Battery Charger

Your scooter is supplied with an off-board charging facility (Image 5).

Please note that only chargers with a capacity of minimum 3.0 Amps and maximum of 6.0 Amps supplied by

your local authorized dealer should be used.

1. Switch your scooter off at the key switch Image 5).

2. Swivel the charge connector cover located on the batter pack and connect the charger (Image 6).

3. Ensure that the charger plug is dry and intact before connecting it to the mains and switching it on.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

4. A reset button is located on the battery.

5. Please check that the button is pressed in (Image 7).

Image 4

Image 5

Image 6

Image 7

Note: The charger is capable of charging from 240V to 100V, and 2Amp, off-board charger has 3 possible

indications:

•RED = Power is on.

•YELLOW = Charging.

•GREEN = fully charged.

Ensure the scooter is switched off before commencing the charging process. After charging, always swivels the

charging socket cover back into place. This helps prevent water getting into the socket (Image 6).

Please note that the scooter has a safety circuit to prevent it from being driven off during charging. If your

scooter fails to respond to normal control after a charging period, please check that the battery charger has been

completely disconnected from the scooter.

The off-board charger must be kept dry in temperatures between -25°C and 40°C and not

be subjected to mechanical damage. In all cases, the charger must only be repaired by an

authorised dealer.

WARNING! You can only use the original charger from the supplier. Using other brand charger may

shorten your warranty period, damage to your scooter, and may cause a fire. Use extreme caution to

manage the battery and charger. Don’t throw the battery into the fire.

You should manage the exhausted battery according to your local laws. Don’t put the battery near any

heating devices, which may cause the battery to explode. Don’t press or subject the battery to intense

pressure or pierce it, which may cause short circuit or overheating.

WARNING! NO SMOKING OR NAKED FLAMES WHEN CHARGING BATTERIES. DO NOT TOUCH

BATTERY PACK TERMINALS WITH METAL OBJECTS. ONLY USE APPROVED REPLACEMENT

BATTERIES. IF DAMAGE TO BATTERIES OR BATTERY BOXES IS EVIDENT, CONTACT YOUR LOCAL

DEALER IMMEDIATELY - DO NOT ATTEMPT TO SERVICE THE BATTERIES. DEALER

WARNING! REMOVE METALLIC JEWELLERY WHEN WORKING WITH BATTERIES. WEAR GLOVES AND

GOGGLES IF MOVING LEAKING BATTERIES. REPLACE DAMAGED OR LEAKING BATTERIES

IMMEDIATELY.

Fuses

•There is a reset button as described previously. If a fault occurs, the button will pop out. Switch the scooter

off, press the button in and switch the scooter back on.

•There is a 30A fuse fitted to the positive terminal of battery. These fuses must be replaced by an authorised

service agent.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

Mobility Scooter – FreeRoam II

•There is also a 2.5A fuse fitted in the charger and a fuse in the mains plug of the battery charger. These

fuses must be replaced by an authorised service agent.

Guidance for Safe Operation and Use

Basic Driving

It is advisable during the first few sessions of operating your scooter that the area around you is clear of

obstacles and pedestrians.

Before operating your scooter, ensure the seat height and position has been adjusted to your satisfaction and

the tiller angle has been set for optimum safety and comfort.

Please see the Safety, Getting on Your Scooter and Tiller Adjustment sections.

1. Make sure you are properly seated on the scooter and that the speed control knob is turned fully to the left.

2. Turn the key switch to the “ON” position.

3. On the tiller, use the throttle lever as described earlier. You will gently accelerate. Release and you will

gently stop. Practice these two basic functions until you get used to them.

4. Steering the scooter is easy and logical. Be sure to remember to allow enough clearance when turning

corners so that the rear wheels clear any obstacle.

5. Shortcutting a pavement corner can cause the back wheel to go off the pavement, causing problems if the

corner is very rough. Avoid this at all times by steering an exaggerated curve around the obstacle.

6. When steering in a tight spot, such as entering a doorway or when turning around, stop the scooter and then

turn the handlebar to where you want to go, then apply power gently. This will make the scooter turn very

sharply. It is also recommended that the pre-set speed is set to a slower setting to aid control in tight spots.

7. Reversing requires attention - exercise caution when reversing especially down slopes. When reversing,

always turn the handlebars in the opposite direction to the way you want to go. The more you operate the

throttle lever, the faster you will go. Reverse speed is 50% slower than forward speed. If the scooter does

not move in reverse, carefully turn the speed control knob clockwise until the scooter moves gently

backwards.

IMPORTANT: To preserve battery power there is a “sleep timer” feature built into the controller. Should the

scooter be left ON, but not operated for 15 minutes, the scooter will go into “sleep mode”. To reset this, switch

the scooter OFF and then back ON again.

NOTE: The user’s visual standards must be higher than 0.5.

Hill Climbing

•This scooter has been tested to climb an incline of no more than 10° with

a maximum user weight of up to 120kg (264 lbs). Do not attempt to climb

inclines in excess of this.

•Always reduce your speed when reversing on slopes. Do not reverse

down hills in excess of 8° and always use extreme caution when

reversing down hills.

•Do not attempt to drive along with the wheels at different levels, e.g.

along the footpath and road simultaneously.

•Hill climbing capability and distance travelled between battery charges will

be adversely affected by such things as:

−The weight of the user.

EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED EQUIPMED

equipmed FreeRoam II User manual

Popular Scooter manuals by other brands