Bissell proheat2x 8920 series User manual

BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691 or
visit the website for helpful instructions at
www.bissell.com
Quick Start
Guide
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
PLEASE KEEP FOR FUTURE REFERENCE
BISSELL Homecare, Inc.
P.O. Box 1888
Grand Rapids, MI 49501
© 2011 BISSELL Homecare, Inc.
1204357
For additional tips and troubleshooting
Please refer to User's Guide
Earn BISSELL rewards! Register your product today!
Visit: www.bissell.com
a.
d.
e.
f.
b.
g.
c.
Phillips head screw driver is needed for assembly
Package contents:
8920, 8930, 8960,
9200, 9300, 9400 SERIES
a. Machine Base & 2 tank system
b. Upper Handle
c. 4 Screws - taped to handle
d. Upper Hose Rack
e. Lower Hose Rack
f. Tool Attachment(s)
(varies by model)
g. Formula
(varies by model)
Carpet cleaning
Cleaning with attachments
1. While pressing the trigger, make one slow forward wet pass and another one back
2. Release the trigger and make one slow forward and backward pass over
the same area. Repeated passes will help aid in dry time
3. Continue passes until cleaning area is complete
4. When the dirty water reaches the “FULL” line on the tank, it is time to empty
5. Empty dirty water by removing tank from base of machine. Carry to sink
or outside to dispose of water. Unlatch top of tank and pour dirty water
through triangle shaped opening in corner
6. Rell as needed, following steps 4 & 5 under "Before you begin cleaning"
1. Set ReadyTools dial to the “TOOLS” setting
2. Attach the cleaning tool to the end of the hose
3. Clean by pressing the trigger to spray solution onto the area to be cleaned
4. Slowly scrub the tool back and forth over the soiled surface
5. Tilt the tool forward to suction liquid
6. When the dirty water reaches the “FULL” line on the tank, follow instruction
#5 under “Carpet Cleaning” to empty tank
7. When cleaning is complete, remove and rinse tool in warm water
5. 6.
WARNING:
Refer to the enclosed user guide for
complete instructions and important
safety notices.
1.
Refer to the User’s Guide for full instructions on how
to clean, store and maintain your machine

1. Slide upper handle onto machine base
2. Screw 3 screws into the marked holes
3. Place upper hose rack onto back of upper handle, and secure with screw
4. Place lower hose rack onto back of upper handle by pushing in and sliding
down until it snaps rmly into place
5. Wrap power cord and ex hose
6. Keep ex hose snugly in place by using the hose secure latch
7. Attach tool to hose grip (extra tool storage on back)
1. Move furniture to another area if cleaning an entire room
2. Remove large dirt and debris from carpet (See User's Guide for more details)
3. Pre-treat spots & stains and heavy trafc areas (optional- see User's Guide)
4. Fill the clean water tank
4a. Unlatch the top by lifting up on tank latch
4b. Remove the top
4c. Fill the bladder with clean hot tap water
4d. Re-attach top by hooking the lip of the tank top into the groove of the
tank bottom and secure the latch
5. Fill the formula tank with water and BISSELL 2X formula
5a. Remove formula tank and unscrew the cap and insert
5b. Fill with water to the WATER line
5c. Fill with BISSELL 2X formula to the FORMULA line
5d. Replace cap and insert and place back into formula tank holder
6. Set Custom Clean Dial (located on the foot of the unit or on the upper handle)
7. Set ReadyTools Dial ("FLOOR CLEANING” for carpet cleaning or “TOOLS”
for cleaning with the hose and tool)
8. Plug into outlet, and turn the power and heater (if desired) switch on
9. If using the heater, let the machine warm up for 1 minute before cleaning
Your assembly is
now complete.
a. Tough Stain Brush
4a.
4d.
6.
4b.
5a.
7.
4c.
5b.
8.
1.
4.
2.
6. 7.
3.
For complete user's guide, visit www.bissell.com
Assembly Before you begin cleaning
a
Power Heater