Black Box VSP-HDMI1X8-4K User manual

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
Page 5 Page 6
© Copyright 2015. Black Box Corporation. All rights reserved.
Black Box and the Double Diamond logo are registered trademarks of
BB Technologies, Inc. Intel is a trademark of Intel Corporation in the U.S.
and/or other countries. Any other trademarks mentioned in this manual
are acknowledged to be the property of the trademark owners.
Distribute HDMI video out
to eight displays.
1 x 8 HDMI Splitter 4K
VSP-HDMI1X8-4K
HDMI Splitter 4K User’s Manual
output signals causing elevated noise levels. Use the proper cable
and make sure the display device can handle the resolution and
refresh rate selected. Interference from nearby electrical devices
can adversely affect signal quality.
Table 4-1. LED indicator functions.
LEDs 1–8 Status
Flashing green Power ON to Port 1, 2, 3, 4, 5, 6,
7, or 8
Steady green Port 1, 2, 3, 4, 5, 6, 7, or 8 is
outputting the video
5. Troubleshooting
Symptom: Video does not display
Possible Cause: Wrong installation process.
Solution: The video splitter requires at least one monitor
connection before powering on the source device.
Symptom: Erratic behavior
Possible Cause: Splitter may not receive enough power.
Solution: Check the power adapter attached to the splitter to
make sure it matches the system specifications, and is functioning
properly.
Symptom: Not receiving picture.
Possible Cause: The signal source may require a display device that
is HDCP compliant.
Solution: Check if the display monitor is HDCP compliant. HDCP
prevents the transfer of digital content to unauthorized HDMI
devices.
Possible Cause: The display monitor is added to the unit by
hot-plug, but the video source may not support hot-plug.
Solution: Check if the video source supports hot-plug. If it doesn’t,
shut down the source device and reboot it again.
Possible Cause: The attached devices are not connected properly.
Solution: Check if you connected your components correctly.
vsp-hdmi1x8-4k_rev1
1. Specifications
Enclosure Metal
Video
Resolution
(Maximum)
4K x 2K (3840x 2160);
Full HD 1080p (1920 x 1080)
User Controls (1) EDID Copy button
Connectors Input: (1) HDMI female,
Output: (8) HDMI female
Indicators (1) Power Input Status LED;
(8) Video Output LEDs
Power Consumption:
9–12 VDC, 130 mA
Dimensions 1.8"H x 8.6"W x 4.6"D
(4.5 x 22 x 11.8 cm)
Weight 1.889 lb. (0.859 kg)
NOTE: The splitter is not 4K compatible when using
Intel®HD 4400 based services.
HDMI Splitter 4K User’s Manual
Disclaimer:
Black Box Network Services shall not be liable for damages of any
kind, including, but not limited to, punitive, consequential or cost
of cover damages, resulting from any errors in the product
information or specifications set forth in this document and
Black Box Network Services may revise this document at any time
without notice.

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
HDMI Splitter 4K User’s Manual HDMI Splitter 4K User’s ManualHDMI Splitter 4K User’s Manual
Page 3Page 2 Page 4
2. Overview
2.1 Introduction
The 1 x 8 HDMI Splitter 4K distributes HDMI video out to eight
displays. It supports up to 4K (UHD) resolutions (3840 x 2160).
Advanced EDID functionality enables the splitter to read and/or
copy EDID information automatically or manually to compatible
screens. The splitter can also be daisychained to support additional
displays.
2.2 Features
• Duplicates one video input to multiple HDMI outputs.
• Unique EDID Copy function provides maximum display
compatibility.
• Learns Video EDID for system integration.
• Automatic power-save for when signal input is lost.
• Cascaded operation for increased signal outputs.
• Provides crisp clear video images.
• Supports EDID and HDCP, and is Blu-ray ready for high definition
display.
• Supports HDMI display resolutions of up to UXGA (1600 x 1200),
WUXGA (1920 x 1200), Full HD 1080p (1920 x 1080), UHD
(3840 x 2160).
• Includes LED indicators for signal activity monitoring.
• Enables accurate and reliable reproduction of digital video signals
without attenuation and distortion.
• Installs in seconds.
2.3 What’s Included
• 1 x 8 HDMI Splitter 4K
• Power adapter with necessary AC cord or plug-in power adapter
• This user’s manual
• (1) set of foot pads
Optional:
• Locking HDMI Cables
2.4 Hardware Description
Figure 2-1. Top panel.
3 4 6 5
Figure 2-2. Back panel.
Table 2-1. Components on the splitter.
No. in Fig.
2-1 and 2-2
Component Description
1LED indicators (8) Video Output LEDs
2LED indicator (1) Power Input Status LED
3Power supply
connector
Apply power from the
power supply to the unit
4Video input port Connects to a video source
5(8) Video output
ports
Connect to monitors
6EDID COPY
Button
Copy the monitor’s EDID
(See EDID Configuration)
NOTE: The splitter is not 4K compatible when using Intel®HD 4400
based services.
3. Installation
3.1 Installing the Splitter
• Before installation, power off all devices that will be connected
to this system.
• Make sure that all devices you will connect are properly grounded.
• Place cables away from fluorescent lights, air conditioners, and
machines that are likely to generate electrical noise.
You will need one HDMI male-to-male cable to connect a video
source to the video splitter’s input port. Connect multiple monitors
or TVs to the video splitter’s output ports.
Turn on your video source only after you’ve made all the
connections.
NOTES:
1. The splitter unit is HDCP compliant and required to use
an HDCP compliant display when it is connecting to the HDCP
video source.
2. Each output port on the splitter must apply the same connection
pattern when a DVI-to-HDMI (or HDMI-to-DVI) adapter is used
for HDMI (or DVI) signal conversion between the splitter and the
HDMI (or DVI) display. Mixed (HDMI and DVI) output
connections may cause signal degradation.
3.2 EDID Configuration
Incorrect EDID communication between the display monitor and
the PC graphics card or insufficient EDID data programmed by
display manufacturers may cause problems. The splitter provides
many ways to read EDID information from the attached video
display and then provides it at all times to the attached video
source. If no new EDID information is available from a display,
the splitter automatically uses a default profile.
To efficiently achieve EDID communication when the video source
is booting up, configure the EDID on the splitter before operation.
3.2.1 EDID Copy
Step 1. Connect the monitor (EDID compliant) to the video output
Port 1 on the splitter and power on the monitor.
Step 2. Press the “EDID COPY” button, then release it RIGHT
AFTER the LED flashes GREEN (about 3 seconds).
Step 3. The LED returns to normal status indicating that EDID copy
is completed.
Otherwise, if the Status LED flashes RED, it means that:
a. The monitor is not properly connected.
b. The monitor is not powered on.
c. EDID data of the monitor is not applicable.
3.2.2 EDID Factory Default Setting
To set the EDID copy to factory default:
Step 1. Press the “EDID COPY” button, then release it RIGHT
AFTER the Status LED flashes PALE BLUE twice (about 9 seconds).
Step 2. The Status LED returns to normal status indicating that
EDID copy is completed.
4. Operation
The quality of the output signal depends on the quality of video
source, cable, and display device used. Low-quality cables degrade
1 2