Black Box LGB5510A Programming manual

Command-Line Interface (CLI) Management Guide
10-Gigabit Web Smart Switch - 10-Port
LGB5510A
Order toll-free in the U.S. or for FREE technical support 24/7: Call 877-877-BBOX
(outside U.S. call 724-746-5500)
www.blackbox.com • [e-mail]
Contact
Information

877-877-2269 | blackbox.com
Table of Contents
Table of Contents
1 CLI Management...................................................................................................................................................................4
1-1 LOGIN .............................................................................................................................................................................4
1-2 COMMANDS OF CLI .......................................................................................................................................................4
2 CLEAR of CLI.........................................................................................................................................................................7
3 CONFIGURE Commands of CLI ..............................................................................................................................................
ACCESS-LIST........................................................................................................................................................................27
3-1 NO .............................................................................................................................................................................28
3-2 QOS .............................................................................................................................................................................43
3-3 SPANNING-TREE ...........................................................................................................................................................45
4 COPY Commands of CLI..................................................................................................................................................... 47
5 DELETE Commands of CLI ..................................................................................................................................................48
6 DIR Commands of CLI ........................................................................................................................................................49
7 DISABLE Commands of CLI ................................................................................................................................................50
8 FIRMWARE of CLI............................................................................................................................................................... 51
9 PING of CLI.........................................................................................................................................................................52
10 RELOAD of CLI...................................................................................................................................................................54
11 SHOW of CLI......................................................................................................................................................................55
12 TERMINAL of CLI ...............................................................................................................................................................76
13 Traceroute..........................................................................................................................................................................77
14 CLI COMMAND REFERENCE ..............................................................................................................................................78

Publication date:Dec., 2015
Revision A1
ii
ABOUT THIS GUIDE
PURPOSE This guide gives specific information on how to operate
and use the management functions of the switch.
AUDIENCE The guide is intended for use by network administrators who
are responsible for operating and maintaining network
equipment; consequently, it assumes a basic working
knowledge of general switch functions, the Internet Protocol
(IP), and Simple Network Management Protocol (SNMP).
CONVENTIONSThe following conventions are used throughout this
guide to show information:
NOTE:Emphasizes important information or calls your attention to
related features or instructions.
CAUTION: Alerts you to a potential hazard that could cause loss of
data, or damage the system or equipment.
WARNING: Alerts you to a potential hazard that could cause personal
injury.
Revision History
Release
Date
Revision
0.83.3*
2015/12/18
A1
*

Publication date: , 2015
Revision A1
4
1 CLI Management
1-1 Login
The command-line interface (CLI) is a text-based interface. Users can access the CLI through either a direct serial
connection to the device or a Telnet session. The default username and password to login into the Managed Switch are
listed below:
Username: admin
Password: <none>
Note: <none> means empty string
After you login successfully, the prompt will be shown as “<sys_name>#“ . See the following two figures. You will log in as
an administrator and have the privilege for setting the Managed Switch. If you log in a user (not the administrator), the
prompt will be shown as “<sys_name>>”. You can only set the system when you are logged in as administrator. Each
CLI command has its privilege.
1-2 Commands of CLI
The CLI is divided into several modes. If a user has enough privileges to run a particular command, the user has to
run the command in the correct mode. To see the commands of the mode, input “?” after the system prompt, then all
commands will be listed in the screen.
Commands that reside in the corresponding modes can run only in that mode. If a user wants to run a particular command,
the user has to change to the appropriate mode. The command modes are organized as a tree, and users start in enable
mode.
1-3 Global Commands of CLI
Username: admin
Password:
LGB5510A#

Publication date: , 2015
Revision A1
5
LGB5510A#
! Comments
clear Reset functions
configure Enter configuration mode
copy Copy from source to destination
delete Delete one file in flash file system
dir Directory of all files in flash file system
disable Turn off privileged commands
exit Exit from the CLI
firmware firmware
more Display file
ping Send ICMP echo messages
reload Reload system
show Show running system information
terminal Set terminal line parameters
traceroute Trace the route to HOST
LGB5510A#

Publication date: , 2015
Revision A1
6
exit
Exit from EXEC mode.
Syntax:
exit
Parameter:
None.
Example:
end
Go back to EXEC mode.
Syntax:
end
Example:
LGB5510A(config)# exit
LGB5510A#
LGB5510A (config)# end
LGB5510A#

Publication date: , 2015
Revision A1
7
2 CLEAR of CLI
Table : CLEAR Commands
Command Function
access-list Access list
logging Syslog
mac MAC Address Table
statistics Clear statistics for a given interface
access-list
Access list.
Syntax:
Clear access-list ace statistics
Parameter:
ace Access list entry
statistics Traffic statistics
Example:
logging
Syslog.
Syntax
clear logging [ info ] [ warning ] [ error ] [ switch <switch_list> ]
Parameter
error Error
info Information
warning Warning
EXAMPLE
LGB5510A mac
LGB5510A# clear access-list ace statistics
LGB5510A#

Publication date: , 2015
Revision A1
8
MAC Address Table.
Syntax
Clear mac address-table
Parameter
address-table Flush MAC Address table.
EXAMPLE
statistics
Clear statistics for a given interface
Syntax
clear statistics interface <port_type> <port_type_list>
clear statistics <port_type> <port_type_list>
Parameter
<port_type_list> 1/1–10 for 10 Gigabit Ethernet
EXAMPLE
LGB5510A# clear mac address-table
LGB5510A#
LGB5510A# clear statistics interface 10GigabitEthernet 1/1-5
LGB5510A#

Publication date: , 2015
Revision A1
9
3 CONFIGURE Commands of CLI
Table : CONFIGURE Commands
Command Function
terminal Configure from the terminal
access-list Access list
aggregation Aggregation mode
clock Configure time-of-day clock
do Run exec commands in config mode
end Go back to EXEC mode
exit Exit from Configuration mode
interface Select an interface to configure
ip Internet Protocol
ipmc IPv4/IPv6 multicast configuration
lacp LACP settings
lldp LLDP configurations.
logging Syslog
loop-protect Loop protection configuration
mac MAC table entries/configuration
monitor Set monitor configuration.
no Negate a command or set its defaults
ntp Configure NTP
qos Quality of Service
spanning-tree Spanning Tree protocol

Publication date: , 2015
Revision A1
10
system Set the SNMP server's configurations
vlan VLAN commands
terminal
Configure from the terminal.
Syntax
configure Terminal
EXAMPLE
aggregation
Aggregation mode.
SYNTAX
aggregation mode {dst-ip | dst-mac | src-dst-ip | src-dst-mac | src-ip | src-mac}
Parameter
mode Traffic distribution mode
dst-ip Destination IP address affects the distribution
dst-mac Destination MAC affects the distribution
src-dst-ip Source and Destination IP affect the distribution
src-dst-mac Source and Destination MAC affect the distribution
src-ip Source IP address affects the distribution
src-mac Source MAC affects the distribution
EXAMPLE
LGB5510A# configure terminal
LGB5510A(config)#

Publication date: , 2015
Revision A1
11
clock
Configure time-of-day clock.
SYNTAX
clock set <icliDate> <icliTime>
clock summer-time mode_type <month> <week> <weekday> <hour> <month> <week number> <week to end>
<hour to end> <offset minutes>
clock timezone <word_var> <hour_var> [ <minute_var> ]
Parameter
set set clock
summer-time Configure summer (daylight savings) time
timezone Configure time zone
<date> yyyy/mm/dd
<time> hh:mm:ss
<2000-2097> Year to start
hh:mm Time to start (hh:mm)
<1-12> Month to end
<1-31> Date to end
<2000-2097> Year to end
hh:mm Time to end (hh:mm)
<1-1440> Offset to add in minutes
<1-5> Week number to start
<1-7> Weekday to start
<1-12> Month to start
LGB5510A(config)# aggregation mode dst-ip
LGB5510A(config)#

Publication date: , 2015
Revision A1
12
EXAMPLE
do
To run exec commands in config mode.
SYNTAX
do < LINE >{[< LINE >]}
Parameter
<LINE>Exec Command
EXAMPLE
interface
Select an interface to configure.
SYNTAX
interface ( <port_type> [ <plist> ] )
interface vlan <vlist>
LGB5510A(config)# clock set 2015/12/14 01:11:11
LGB5510A(config)# do show clock
System Time : 2015-12-14 01:11:30
LGB5510A(config)# clock summer-time enable 1 1 1 1 1 1 1 1 1
LGB5510A(config)#
LGB5510A(config)# do show vlan
VLAN Name Ports
--------------------------------------------------------------------------------
--------------------
1 default GigabitEthernet 1/1, GigabitEthernet 1/2,
GigabitEthernet 1/3,
GigabitEthernet 1/4, GigabitEthernet 1/5
LGB5510A(config)#

Publication date: , 2015
Revision A1
13
Parameter
vlan VLAN interface configurations
<vlan_list> List of VLAN interface numbers, 1-4095
<port_type_list> 1/1-10 for 10 Gigabit Ethernet
EXAMPLE
ip
Internet Protocol.
SYNTAX
ip arp inspection
ip arp inspection entry interface <port_type> <in_port_type_id> <vlan_var> <mac_var> <ipv4_var>
ip arp inspection translate [ interface <port_type> <in_port_type_id> <vlan_var> <mac_var> <ipv4_var> ]
ip arp inspection vlan <in_vlan_list>
ip arp inspection vlan <in_vlan_list> logging { deny | permit | all }
ip dhcp excluded-address <low_ip> [ <high_ip> ]
ip dhcp pool <pool_name>
ip dhcp relay
ip dhcp relay information option
ip dhcp relay information policy { drop | keep | replace }
ip dhcp server
ip dhcp snooping
LGB5510A(config)# interface vlan 1
LGB5510A(config-if-vlan)# ip address 192.168.1.22 255.255.255.0
LGB5510A(config-if-vlan)# exit
LGB5510A(config)# interface 10GigabitEthernet 1/1-10
LGB5510A(config-if)# flowcontrol on
LGB5510A(config-if)#

Publication date: , 2015
Revision A1
14
ip igmp host-proxy [ leave-proxy ]
ip igmp snooping
ip igmp snooping vlan <v_vlan_list>
ip igmp ssm-range <v_ipv4_mcast> <ipv4_prefix_length>
ip igmp unknown-flooding
ip name-server { <v_ipv4_addr> | dhcp [ interface vlan <v_vlan_id> ] }
ip route <v_ipv4_addr> <v_ipv4_netmask> <v_ipv4_gw>
ip source binding interface <port_type> <in_port_type_id> <vlan_var> <ipv4_var> <mac_var>
ip verify source
ip verify source translate
Parameter
arp Address Resolution Protocol
dhcp Dynamic Host Configuration Protocol
igmp Internet Group Management Protocol
name-server Domain Name System
route Add IP route
source Source command
ssh Secure Shell
verify Verify command
inspection ARP inspection
entry ARP inspection entry
interface ARP inspection entry interface config
<port_type_id> Port ID in the format of switch-no/port-no
<vlan_id> Select a VLAN id to configure
<mac_ucast> Select a MAC address to configure
<ipv4_ucast> Select an IP Address to configure

Publication date: , 2015
Revision A1
15
deny Log denied entries
permit Log permitted entries
all Log all entries
translate Arp inspection translate all entries
vlan Arp inspection vlan setting
<vlan_list> Arp inspection vlan list
relay DHCP relay agent information
information DHCP information option <Option 82>
option DHCP option
information DHCP information option(Option 82)
policy Policy for handling the receiving DHCP packet already include the information option
drop Drop the package when receive a DHCP message that already contains relay information
keep Keep the original relay information when receive a DHCP message that already contains it
server Enable DHCP server
snooping DHCP snooping
proxy DNS proxy service
secure-redirect Secure HTTP web rediction
secure-server Secure HTTP web server
snooping Snooping IGMP
<word16> Profile name in 16 char's
vlan IGMP VLAN
ssm-range IPv4 address range of Source Specific Multicast
<ipv4_mcast> Valid IPv4 multicast address
<4-32> Prefix length ranges from 4 to 32
unknown-flooding Flooding unregistered IPv4 multicast traffic
<ipv4_ucast> A valid IPv4 unicast address

Publication date: , 2015
Revision A1
16
dhcp Dynamic Host Configuration Protocol
interface Select an interface to configure
vlan VLAN Interface
<vlan_id> VLAN identifier(s): VID
<ipv4_addr> Network
<ipv4_netmask> Netmask
<ipv4_addr> Gateway
binding IP source binding
interface IP source binding entry interface config
* All switches or All ports
10 Gigabitethernet 10 Gigabit Ethernet Port
<port_type_id> Port ID in the format of switch-no/port-no, ex 1/1-10 for 10 Gigabit Ethernet
<vlan_id> Select a VLAN id to configure
<ipv4_ucast> Select an IP Address to configure
<ipv4_netmask> Select a subnet mask to configure
<mac_ucast> Select a MAC address to configure
source verify source
limit limit command
<0-2> the number of limit
translate IP verify source translate all entries
loggin ARP inspection vlan loging mode config
EXAMPLE

Publication date: , 2015
Revision A1
17
ipmc
IPv4/IPv6 multicast configuration.
SYNTAX
ipmc profile
ipmc profile <profile_name>
ipmc range <entry_name> { <v_ipv4_mcast> [ <v_ipv4_mcast_1> ] | <v_ipv6_mcast> [ <v_ipv6_mcast_1> ] }
Parameter
profile IPMC profile configuration
range A range of IPv4/IPv6 multicast addresses for the profile
< word16> Range entry name in 16 char's
<ipv4_mcast> Valid IPv4 multicast address
<ipv6_mcast> Valid IPv6 multicast address
EXAMPLE
lacp
LACP settings.
LGB5510A(config)# ip arp inspection
LGB5510A(config)# ip dhcp relay
LGB5510A(config)# ip helper-address 192.168.1.1
LGB5510A(config)# ip igmp snooping vlan 3
LGB5510A(config)# ip name-server 192.168.1.6
LGB5510A(config)# ip route 192.168.1.1 255.255.255.0 192.168.1.100
LGB5510A(config)# ip routing
LGB5510A(config)# ip verify source translate
IP Source Guard:
Translate 0 dynamic entries into static entries.
LGB5510A(config)# ipmc profile test
LGB5510A(config-ipmc-profile)#

Publication date: , 2015
Revision A1
18
SYNTAX
lacp system-priority <1-65535>
Parameter
system-priority System priority
<1-65535> Priority value, lower means higher priority
EXAMPLE
lldp
LACP configurations.
SYNTAX
lldp holdtime <2-10>
lldp med datum { wgs84 | nad83_navd88 | nad83_mllw }
lldp med fast <1-10>
lldp med location-tlv altitude { meters | floors } <word11>
lldp med location-tlv civic-addr { country | state | county | city | district | block | street | leading-street-direction |
trailing-street-suffix | street-suffix | house-no | house-no-suffix | landmark | additional-info | name | zip-code |
building | apartment | floor | room-number | place-type | postal-community-name | p-o-box | additional-code }
<string250>
lldp med location-tlv elin-addr <dword25>
lldp med location-tlv latitude { north | south } <word8>
lldp med location-tlv longitude { west | east } <word9>
lldp med media-vlan policy-list <range_list>
lldp med media-vlan-policy <0-31> { voice | voice-signaling | guest-voice-signaling | guest-voice |
softphone-voice | video-conferencing | streaming-video | video-signaling } { tagged <vlan_id> | untagged }
[ l2-priority <0-7> ] [ dscp <0-63> ]
lldp reinit <1-10>
LGB5510A(config)# lacp system-priority 333
LGB5510A(config)#

Publication date: , 2015
Revision A1
19
lldp timer <5-32768>
lldp transmission-delay <1-8192>
Parameter
holdtime Sets LLDP hold time (The neighbor switch will
discarded the LLDP information after "hold time"
multiplied with "timer" seconds ).
med Media Endpoint Discovery.
reinit LLDP tx reinitialization delay in seconds.
timer Sets LLDP TX interval (The time between each LLDP
frame transmitted in seconds).
transmission-delay Sets LLDP transmision-delay. LLDP transmission delay
(the amount of time that the transmission of LLDP
frames will delayed after LLDP configuration has
changed) in seconds.)
<2-10> 2-10 seconds.
<1-10> 1-10 seconds.
<5-32768> 5-32768 seconds.
<1-8192> 1-8192 seconds.
datum Datum (geodetic system) type.
fast Number of times to repeat LLDP frame transmission at
fast start.
location-tlv LLDP-MED Location Type Length Value parameter.
media-vlan-policy Use the media-vlan-policy to create a policy, which
can be assigned to an interface.
nad83_mllw Mean lower low water datum 1983
nad83_navd88 North American vertical datum 1983

Publication date: , 2015
Revision A1
20
wgs84 World Geodetic System 1984
altitude Altitude parameter
meter Altitude value
floors Altitude value
civic-addr Civic address information and postal information
country The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or
US.
state National subdivisions (state, canton, region, province, prefecture).
county County, parish, gun (Japan), district.
city City, township, shi (Japan) - Example: Copenhagen.
district City division, borough, city district, ward, chou (Japan).
block Neighbourhood, block.
street Street - Example: Poppelvej.
leading-street-direction Leading street direction - Example: N.
trailing-street-suffix Trailing street suffix - Example: SW.
street-suffix Street suffix - Example: Ave, Platz.
house-no House number - Example: 21.
house-no-suffix House number suffix - Example: A, 1/2.
landmark Landmark or vanity address - Example: Columbia University.
additional-info Additional location info - Example: South Wing.
name Name (residence and office occupant) - Example: Flemming Jahn.
zip-code Postal/zip code - Example: 2791.
building Building (structure) - Example: Low Library.
apartment Unit (Apartment, suite) - Example: Apt 42.
floor Floor - Example: 4.
room-number Room number - Example: 450F.