Black Box ServSwitch User manual

ACX0000 ACX0832
ACX0808 ACX1616
ACX0816 ACX1632
ServSwitchTM DKM
Manual
http://www.blackbox.com

ServSwitch™ DKM
1
Welcome to the ServSwitch™ Family!
Thank you for purchasing a ServSwitch™ DKM! We appreciate your business, and we think
you’ll appreciate the many ways that your ServSwitch™ DKM will save you money, time,
and effort.
The ServSwitch™ DKM offers four fundamental uses:
 As a Crosspoint Switch with a maximum of 32 input ports and 16 output ports.
Optionally, in reverse mode, the device supports a maximum of 16 input ports and
32 output ports. Thus, you can, for example, switch and distribute the signals from
multiple signal sources on up to 32 displays (allowing explicitly simultaneous
presentations on several displays). Alternatively, signals coming from up to 32
signal sources can be switched in turn to a single display. The changeover can be
triggered remotely using the remote control (included), the serial interface (RS232)
and/or by the built-in web interface.
 As a KVM Switch with a maximum of 32 CPU ports and 16 Console ports. The
ports can be configured as Single-Head ports (a “Single-Head” extender system
supports 1x monitor, 1x keyboard, 1x mouse), Dual-Head ports (a Dual-Head
extender system supports 2x monitor, 1x keyboard, 1x mouse) or even Quad-Head
ports (a Quad -Head extender system supports 4x monitor, 1x keyboard, 1x mouse).
The changeover can be triggered remotely using the remote control (included), the
serial interface (RS232) and/or by the built-in web interface.
 In KVM Switch Mode CPU Ports and CON Ports can be configured as USB2.0
Ports. This can be done for single Ports as well as for combinations of one Single-
Head (Triple-Head-)Port and one USB2.0 Port. In the latter case the respective
consoles will always be switched together with its assigned USB2.0 Port.
 As a special case of the KVM Switch, you can choose the “Control Room” Mode
with 2, 4 or 8 monitors. In “Control Room” Mode, up to 8 CPU’s are permanently
displayed on up to 8 monitors. With a hotkey, you can switch to any of these
monitors for operation.
 In “Teacher/Student” Mode, the teacher can attend up to 31 students.
The ServSwitch™ DKM has the advantage that it can be positioned (CATx version) up to
140m away from both your signal source and display device. This becomes possible by using
the proven ServSwitch™- Extender technology for the transmission of DVI- Monitor and
USB-Keyboard and Mouse signals over CATx cable.
The operation of a ServSwitch™ DKM always requires up to 32 Local Units and up to 16
Remote Units from the ServSwitch™-Extenders range.

ServSwitch™ DKM
2
Wherever long distances cause problems for remotely locating and switching a monitor
(keyboard/mouse) signal, e.g. airports, industrial plants, call centres or in distributed
computer centres, the ServSwitch™ DKM is the best solution to distribute and switch
monitor (keyboard/mouse) signals. Its flexibility allows it to tackle almost every task.
There are 8 pre-configured ServSwitch™ DKMes for CATx as well as an empty chassis for
individual configuration. In addition, there are 4 Media Extenders (DVI + optional audio) and
8 KVM- Extenders (DVI+USB keyboard mouse + optional audio) available. The
transmission of the signals requires connecting CATx cable.
For fibre applications, all switch elements and extenders are also available in multimode or
singlemode versions, requiring the respective cabling.
This manual will tell you all about your new ServSwitch™ DKM, including how to install,
operate and troubleshoot it. For an introduction to the device, see Chapter 2.
The product codes covered in this manual are:
ServSwitch™ DKM Devices for CATx
ACX0808: ServSwitch™ DKM for 8 User and 8 CPUs
ACX0816: ServSwitch™ DKM for 8 User and 16 CPUs
ACX0824: ServSwitch™ DKM for 8 User and 24 CPUs ***
ACX0832: ServSwitch™ DKM for 8 User and 32 CPUs
ACX1608: ServSwitch™ DKM for 16 User and 8 CPUs***
ACX1616: ServSwitch™ DKM for 16 User and 16 CPUs
ACX1624: ServSwitch™ DKM for 16 User and 24 CPUs***
ACX1632: ServSwitch™ DKM for 16 User and 32 CPUs
ACX0000: ServSwitch™ DKM for individual configuration
ServSwitch™ DKM Devices for Multimode/Singlemode and ***marked versions… to
be individually configured, deriving from ACX0000 or others

ServSwitch™ DKM
3
CATx Local and Remote Units
ACS4100A-T: ServSwitch™-Media Local Unit
ACS4122A-T: ServSwitch™-Media Local Unit, +Audio
ACS4001A-T: ServSwitch™- KVM Local Unit, Single-Head
ACS4201A-T: ServSwitch™- KVM Local Unit, Dual-Head
ACS4022A-T: ServSwitch™- KVM Local Unit, +Audio, Single-Head
ACS4222A-T: ServSwitch™- KVM Local Unit, +Audio, Dual-Head
ACS4004A-T: ServSwitch™-KVM Local Unit, Single-Head, 4x USB-HID
ACS4204A-T: ServSwitch™-KVM Local Unit, Dual-Head, 4x USB-HID
ACS4002A-T: ServSwitch™- KVM Local Unit, +USB2.0, Single Head
ACS4011A-T: ServSwitch™- KVM Local Unit, +VGA, Single-Head
ACS4100A-R: ServSwitch™-Media Remote Unit
ACS4122A-R: ServSwitch™-Media Remote Unit, +Audio
ACS4001A-R: ServSwitch™- KVM Remote Unit, Single-Head
ACS4201A-R: ServSwitch™- KVM Remote Unit, Dual-Head
ACS4022A-R: ServSwitch™- KVM Remote Unit, +Audio, Single-Head
ACS4222A-R: ServSwitch™- KVM Remote Unit, +Audio, Dual-Head
ACS4004A-R: ServSwitch™-KVM Remote Unit, Single-Head, 4x USB-HID
ACS4204A-R: ServSwitch™-KVM Remote Unit, Dual-Head, 4x USB-HID
ACS4002A-R: ServSwitch™- KVM Remote Unit, +USB2.0, Single Head

ServSwitch™ DKM
4
Multimode Local and Remote Units
ACS4100A-T-MM: ServSwitch™-Media Local Unit
ACS4122A-T-MM: ServSwitch™-Media Local Unit, +Audio
ACS4001A-T-MM: ServSwitch™- KVM Local Unit, Single-Head
ACS4201A-T-MM: ServSwitch™- KVM Local Unit, Dual-Head
ACS4022A-T-MM: ServSwitch™- KVM Local Unit, +Audio, Single-Head
ACS4222A-T-MM: ServSwitch™- KVM Local Unit, +Audio, Dual-Head
ACS4004A-T-MM: ServSwitch™-KVM Local Unit, Single-Head, 4x USB-HID
ACS4204A-T-MM: ServSwitch™-KVM Local Unit, Dual-Head, 4x USB-HID
ACS4002A-T-MM: ServSwitch™- KVM Local Unit, +USB2.0, Single Head
ACS4011A-T-MM: ServSwitch™- KVM Local Unit, +VGA, Single-Head
ACS4100A-R-MM: ServSwitch™-Media Remote Unit
ACS4122A-R-MM: ServSwitch™-Media Remote Unit, +Audio
ACS4001A-R-MM: ServSwitch™- KVM Remote Unit, Single-Head
ACS4201A-R-MM: ServSwitch™- KVM Remote Unit, Dual-Head
ACS4022A-R-MM: ServSwitch™- KVM Remote Unit, +Audio, Single-Head
ACS4222A-R-MM: ServSwitch™- KVM Remote Unit, +Audio, Dual-Head
ACS4004A-R-MM: ServSwitch™-KVM Remote Unit, Single-Head, 4x USB-
HID
ACS4204A-R-MM: ServSwitch™-KVM Remote Unit, Dual-Head, 4x USB-
HID
ACS4002A-R-MM: ServSwitch™- KVM Remote Unit, +USB2.0, Single Head

ServSwitch™ DKM
5
Singlemode Local and Remote Units
ACS4100A-T-SM: ServSwitch™-Media Local Unit
ACS4122A-T-SM: ServSwitch™-Media Local Unit, +Audio
ACS4001A-T-SM: ServSwitch™- KVM Local Unit, Single-Head
ACS4201A-T-SM: ServSwitch™- KVM Local Unit, Dual-Head
ACS4022A-T-SM: ServSwitch™- KVM Local Unit, +Audio, Single-Head
ACS4222A-T-SM: ServSwitch™- KVM Local Unit, +Audio, Dual-Head
ACS4004A-T-SM: ServSwitch™-KVM Local Unit, Single-Head, 4x USB-HID
ACS4204A-T-SM: ServSwitch™-KVM Local Unit, Dual-Head, 4x USB-HID
ACS4002A-T-SM: ServSwitch™- KVM Local Unit, +USB2.0, Single Head
ACS4011A-T-SM: ServSwitch™- KVM Local Unit, +VGA, Single-Head
ACS4100A-R-SM: ServSwitch™-Media Remote Unit
ACS4122A-R-SM: ServSwitch™-Media Remote Unit, +Audio
ACS4001A-R-SM: ServSwitch™- KVM Remote Unit, Single-Head
ACS4201A-R-SM: ServSwitch™- KVM Remote Unit, Dual-Head
ACS4022A-R-SM: ServSwitch™- KVM Remote Unit, +Audio, Single-Head
ACS4222A-R-SM: ServSwitch™- KVM Remote Unit, +Audio, Dual-Head
ACS4004A-R-SM: ServSwitch™-KVM Remote Unit, Single-Head, 4x USB-
HID
ACS4204A-R-SM: ServSwitch™-KVM Remote Unit, Dual-Head, 4x USB-HID
ACS4002A-R-SM: ServSwitch™- KVM Remote Unit, +USB2.0, Single Head

ServSwitch™ DKM
6
Copyrights and Trademarks
©2009. All rights reserved. This information may not be reproduced in any manner without
the prior written consent of the manufacturer.
Information in this document is subject to change without notice and the manufacturer shall
not be liable for any direct, indirect, special, incidental or consequential damages in
connection with the use of this material.
All trademark and trade names mentioned in this document are acknowledged to be the
property of their respective owners.
Disclaimer
While every precaution has been taken in the preparation of this manual, the manufacturer
assumes no responsibility for errors or omissions. Neither does the manufacturer assume any
liability for damages resulting from the use of the information contained herein. The
manufacturer reserves the right to change the specifications, functions, or circuitry of the
product without notice.
The manufacturer cannot accept liability for damage due to misuse of the product or due to
any other circumstances outside the manufacturer’s control (whether environmental or
installation related). The manufacturer shall not be responsible for any loss, damage, or injury
arising directly, indirectly, or consequently from the use of this product.
Cautions and Notes
The following symbols are used in this guide:
CAUTION: This indicates an important operating instruction
that should be followed to avoid any potential damage to
hardware or property, loss of data, or personal injury.
NOTE. This indicates important information to help you make the best use of
this product.

EMPTY PAGE
7

ServSwitch™ DKM
8
EC DECLARATION OF CONFORMITY
The products listed below in the form as delivered are in conformity with the provisions
of the following European Directives:
2004/108/EG Council Directive on the approximation of the laws of the Member States
relating to electromagnetic compatibility
CE-marking 2009
Product list:
List on page 2 - 5
Conformity to the Directives is assured through the application of the following
standards:
EN 55022: 09/2006 Class A
IEC 61000-4-2: 02/2001
IEC 61000-4-3: 05/2006
IEC 61000-4-4: 12/2004
IEC 61000-4-5: 11/2006
This declaration certifies the conformity to the specified directives but contains no
assurance of properties. The safety documentation noted in this manual shall be
considered in detail. The length of the attached CPU- or Console Cables must not exceed
3m. The use of suggested interconnect cables is mandatory.









WARNING: This equipment has been found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

SAFETY PRECAUTIONS AND
INSTALLATION GUIDLINES
9
Safety Precautions and Installation Guidelines
To ensure reliable and safe long-term operation, please note the following installation
guidelines:
 Do not use CATx- devices to link between buildings – please use fibre devices.
 Only use in dry, indoor environments.
 If the building has 3-phase AC power, try to ensure that equipment connected to the
Local and Remote Units is on the same phase.
 Try not to route a CATx- link cable alongside power cables.
 The Remote Unit, Local Unit and any power supplies can get warm. Do not locate them
in an enclosed space without any airflow.
 Do not place a power supply directly on top of a unit.
 Do not obscure a unit’s ventilation holes.
To safeguard against personal injury and avoid possible
damage to equipment or property, please observe the
following:
 Only use power supplies originally supplied with the
product or manufacturer-approved replacements. Do not
attempt to dismantle or repair any power supply. Do not
use a power supply if it appears to be defective or has a
damaged case.
 Connect all power supplies to grounded outlets. In each
case, ensure that the ground connection is maintained
from the outlet socket through to the power supply’s AC
power input.
 Do not attempt to modify or repair this product, or make
a connection from the CATx- link interface (RJ45) to any
other products, especially telecommunications or
network equipment.

ServSwitch™ DKM
10
Contents
1Quick Setup 14
2Overview 15
2.1 Introduction 15
2.2 Glossary 17
2.3 Example of a ServSwitch™ DKM System 18
2.4 Features 19
2.5 Product Range 21
2.6 Compatibility 25
2.7 How to Use This Guide 26
2.7.1 Connection & Compatibility 26
2.7.2 DDC Information 26
2.7.3 Selecting the moment of switching to the next frame 26
2.7.4 Selection of Color reduction for transfer acceleration 27
3Installation 28
3.1 Package Contents 28
3.2 Interconnection Cable Requirements 30
3.3 System Setup 32
3.4 Installation Instructions 33
4Device Views 34
4.1 ServSwitch™ DKM 34
5Diagnostic 36
5.1 ServSwitch™ DKM – I/O Boards 36
6ServSwitch™ DKM Configuration 38
6.1 Configuration via Console 38
6.1.1 On-Screen Display (OSD) 38
6.1.2 Open „Configuration“ Menu 43
6.1.3 Load Configurations 45
6.1.4 System Configurations 46
6.1.5 Touch Screen Settings 51
6.1.6 Configuration of User Attributes 52
6.1.7 User Matrix Configuration 53
6.1.8 Configuration of CON Ports 55
6.1.9 CON Matrix Configuration 57
6.1.10 Configuration of CPU Ports 59
6.1.11 Configuration of Network Parameters 60
6.1.12 Programming of Macros 61
6.1.13 Saving Configurations inside the Switch 63
6.1.14 Saving Configurations into File 64

CONTENTS
11
6.1.15 Restart your Switch 65
6.2 Configuration via Browser and Web Interface 66
6.3 Configuration via Serial Interface 67
6.4 Configuration via IR Remote Control and LCD-Display 68
6.4.1 IR Remote Control 68
6.4.2 Home Mask 69
6.4.3 Menu Mask 69
6.4.4 Configuration Mask 70
6.4.5 Configuration of Network Parameters 71
6.4.6 Configuration of System Parameters 72
6.4.7 Restart your Switch 74
6.4.8 Reset your Switch 74
6.5 Configuration via FTP 75
6.5.1 FTP Access to Configuration Files 75
6.5.2 External Saving of Configuration Files 76
6.5.3 Loading External Configuration Files 76
7Status Information 77
7.1 Status Display via Console and OSD 78
7.1.1 Open the „Status“ Menu 78
7.1.2 Status Display of CON Ports 79
7.1.3 Status Display of CPU Ports 81
7.1.4 Display of Network Status 83
7.1.5 Display of Firmware Status 85
7.2 Status Display via Browser / Web Interface 87
7.3 Status Display via Serial- Interface 88
7.4 Status Display via LCD-Display 89
7.4.1 Home Mask 89
7.4.2 Menu Mask 89
7.4.3 Status Mask 90
7.4.4 Display of CPU-/CON-Ports Status 90
7.4.5 Display of Network Status 91
7.4.6 Display of Flash Status 93
7.4.7 Display of Tasks Status 95
8Control of ServSwitch™ DKM 96
8.1 Instant Switching 97
8.1.1 Keyboard Hot Keys 97
8.1.2 Changing the default Instant Switching Hotkey 97
8.1.3 Macro Keyboard 98
8.1.4 Macros via Function keys of a standard keyboard 98
8.2 Switching in OSD / KVM Mode 99
8.2.1 Switching in „KVM-List“ Mask: 99
8.2.2 Switching in „KVM-Switch“ Mask: 101
8.2.3 Switching in „Follow Me“ Mask: 103
8.3 Switching in OSD / Crosspoint Mode 104
8.3.1 Open the „CP-Switch“ Menu 105
8.3.2 Switching in „Crosspoint Switch / CON Ports“ Mask 106
8.3.3 Switching in „Crosspoint Switch / CPU Ports“ Mask“ 108
8.4 Switching via Browser / Web Interface 110

ServSwitch™ DKM
12
8.5 Switching via Serial Interface 111
8.6 Switching via LCD-Display 112
9Operating Modes 113
9.1 Single-Head KVM-Switch 114
9.2 Dual-Head KVM-Switch 115
9.3 Quad-Head KVM-Switch 116
9.4 Single-Head KVM/USB2.0 Mode 117
9.5 Triple-Head KVM/USB2.0 Mode 118
9.6 Teacher/Student System 15 119
9.7 Teacher/Student System 30 120
9.8 Crosspoint Switch 121
10Troubleshooting 122
10.1 Monitor 122
10.2 USB HID 123
Appendix A: Example Applications 125
Appendix B: Rack Mount Options 129
Appendix C: Serial Interface 133
Appendix D: Network Interface 138
Appendix E: Calling Technical Support 139
Appendix F: List of supported USB devices 140
Appendix G: Specifications 141
Appendix H: Connectors 143
Appendix I: ServSwitch™ Media/KVM Extender 144
I.1. ServSwitch™- Media Extender 144
I.2. ServSwitch™- KVM Extender 146
I.3. Diagnostics of ServSwitch™- Media/ KVM 157
I.4. Service Setup Extenders 158
I.5. Setup at the Local Unit 159
I.6. Setup at the Remote Unit 161

CONTENTS
13
I.7. Devices with serial/audio option 162
I.8. Specifications ServSwitch™-Media/KVM Units 164
I.9. Connectors ServSwitch™-Media/KVM Units 167

ServSwitch™ DKM
14
1 Quick Setup
This section briefly describes how to install your ServSwitch™ DKM system. Unless you are
an experienced user, we recommend that you follow the full procedures described in the rest
of this manual.
Installation of the system
Connect ServSwitch™ DKM to Local unit(s) with CATx/Fibre cable(s).
Connect ServSwitch™ DKM to Remote unit(s) with CATx/Fibre cable(s).
Connect the devices to the power supplies.
Power up the system.
Done
YES
NO
Link LED
illuminated?
NO
YES
Check p.s.u.’s and connection to
power outlet
Power LED
illuminated?
Check the CATx- cable, and
CATx- connectors

OVERVIEW
15
2 Overview
2.1 Introduction
The ServSwitch™ DKM can be set up to support four different applications:
 Crosspoint Switch: Maximum configuration (without cascading) of 32 input ports
and 16 output ports. Optionally, in reverse mode, the device supports a maximum
of 16 input ports and 32 output ports.
Set-Up: Local units are installed at up to 32 DVI signal sources. The Crosspoint
Switch may now be installed up to 10 km away from the sources.
The received signals (DVI + optional serial/Audio) can now be switched to the
respective output ports. One input signal may be distributed simultaneously to
several output ports.
From these output ports, the displays (again, up to 10 km away) are controlled via
remote units to be installed at each display. The changeover can be triggered
remotely using the serial interface (RS232) and/or by the built-in web interface.
 KVM Switch: As a KVM Switch the device supports several operation modes:
16 User ports on 32 CPU ports for Single-Head access, 8 User ports on 16 CPU
ports for Dual-Head access or even 4 User ports on 8 CPU ports for Quad-Head
access.
Single-Head/ Dual-Head/ Quad-Head CPUs/ and User ports may also be operated
in mixed mode. In this case, the maximum number of User ports depends on the
detailed configuration.
A maximum of 32 CPUs (up to 10 km away) can be connected to the KVM Switch
via Local units to be installed at each CPU.
The received signals (DVI, Keyboard, Mouse + optional serial/Audio) can now be
switched to the respective output ports. From these output ports, up to 16 consoles
(again, up to 10 km away) are controlled via remote units to be installed at each
console.
The changeover can be triggered remotely by a hotkey sequence (only in KVM
mode), using the serial interface (RS232) or by the built-in web interface.
A comfortable OSD (On Screen Display) allows the selection of the CPUs, user
administration and offers further administrative functions.
A special function called “Partner Viewing” allows copying one (or more) display
signal(s) to one or more additional displays. This mode is especially useful e.g. if
one display signal shall be shown on both the user display and a beamer or if the
monitor information shall be shared with an administrator. The “Follow Me”
function ensures that the monitor information is updated whenever the original
display signal source is changed.

ServSwitch™ DKM
16
 “Control Room” Mode: As a special case of the KVM Switch, you can choose
the “Control Room” Mode. In this mode, several displays are assigned to a work
place. A comfortable OSD (On Screen Display) allows at any time to choose from a
list of available CPUs the CPU to be displayed on a specific monitor.
With a hotkey sequence, you can switch keyboard and mouse to any of these
monitors for operation without need to know the associated CPU. Now you can
operate this CPU.
Also in this mode, one (or more) display signal(s) can be copied to one or more
additional displays (“Partner Viewing”).
 “Teacher/Student” System: Two configurations are available:
a) Attend up to 15 Students – Each student work place is connected by CATx-
Duplex cable. Each CPU can be displayed at any work place – both student and
teacher work place – even simultaneously. The teacher can observe every student
work place.
b) Attend up to 31 Students – Each student work place is connected by CATx-
Simplex cable. Each CPU can be displayed at a specific monitor, e.g. beamer or
large display – both student and teacher work place. The teacher can observe every
student work place.
A ServSwitch™ DKM system comprises a ServSwitch™ DKM and one or more
Local/Remote Units. The ServSwitch™ DKM and the Local/ Remote Units are attached by
CATx or Fibre interconnection cables.
The operation of a ServSwitch™ DKM requires always the use of Local Units and Remote
Units of a ServSwitch™-Extender.

OVERVIEW
17
2.2 Glossary
The following terms are used in this guide:
CATx Any Category 5, 5e, 6 or higher cable, solid wires type AWG24.
If Patch Cables are used, all distances count twice.
Fibre Singlemode or Multimode fibre cable.
Singlemode 9µ Singlemode fibre cable.
Multimode 62,5µ Multimode- or 50µ Multimode fibre cable.
KVM Keyboard, Video and Mouse.
Console Keyboard, Mouse and Monitor
Dual Access A system allowing connection of Local and Remote User Consoles.
Single-Head An extender system that supports one Monitor + Keyboard/ Mouse
Dual-Head An extender system that supports two Monitors + Keyboard/ Mouse
Quad-Head An extender system that supports four Monitors + Keyboard/ Mouse
DVI Digital Video standard, installed by Digital Display Working Group
(www.ddwg.org) R, G, B, CLOCK in a data stream with up to
3x1,6 Gbit/sec. Signals are TMDS Level.
PSU The desktop power supply connected to the ServSwitch™ DKM or to
the Local/ Remote Unit.
HID Human Interface Devices are units, which are used for human access
to the CPU: keyboard and mouse, touch-screen, light pen, fingerprint
sensor, graphic tablets etc.

ServSwitch™ DKM
18
2.3 Example of a ServSwitch™ DKM System
Application example for a ServSwitch™ DKM System
(Single-Head KVM Switch)

OVERVIEW
19
2.4 Features
The ServSwitch™ DKM offers the following features:
 Support for DVI-D Graphic cards (all devices)
 Support for USB-Keyboard and USB-Mouse (KVM-Extender)
ServSwitch™- KVM standard devices with USB-HID connectors support
the extension of keyboard and mouse ONLY; use with other HID devices
(Human Interface Device) such as touch screens, graphics tablets, barcode
readers or similar may be successful – but there is no guarantee for this!
The ServSwitch™- KVM standard device is NOT suitable for use with
other USB- devices such as scanners, web- cams, data sticks etc.
ServSwitch™- KVM standard devices support only two devices
simultaneously – keyboard and mouse or keyboard and touch-screen, etc.
but not e.g. keyboard, mouse and touch-screen simultaneously. You can
extend by a USB hub but this does not raise the number of supported
devices.
 Maximum length of interconnection cable from a Local Unit to a ServSwitch™- Minor
Switch, between two ServSwitch™- Minor Switches or from a ServSwitch™- Minor
Switch to a Remote Unit).
 140m (400ft) with CATx- cable
 200 m mit Multimode 62.5μm
 400 m mit Multimode 50μm
 10.000 m mit Singlemode 9μm
 Maximum Resolution (DVI): 1920x1200@60Hz
 Supports:16/24 Bit auto-switching or 24 Bit (= full) color depth (selectable)
 Status indicator LEDs for Power and Link on each device.
 Compact footprint chassis.
 Rack mount options available.
 International power supplies included.
 Options:
 USB 2.0 Support
 Bidirectional Audio Interface
 Serial Interface
 Single-Head Devices support a transparent serial interface with up to 19.2
KBaud and Hardware handshake. This serial interface can be used to control a
single device requiring full Hardware handshake or up to three devices without
Handshake (XON/XOFF)