Black Box SWI037A User manual

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax [phone]
© Copyright 1998. Black Box Corporation. All rights reserved.

CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax [phone]
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
JUNE 1998
SWI037A
SWI037AE
SWI038A
SWI038AE
POW-R-SWITCH 8C
POWER
8
7
6
5
4
3
2
1RESET
DTE/DCE
SELECT
OUTLETS
SW 2
SW 1
1
OUTPUTS
234
POWER
SW1 SW2 DTE/DCE
SELECT
RESET
POW-R-SWITCH 4C
Pow-R-Switches 4C and 8C

1
TRADEMARKS
TRADEMARKS USED IN THIS MANUAL
AT is a registered trademark of IBM Corporation.
All applied-for and registered trademarks are the property of their respective owners.

2
POW-R-SWITCHES 4C AND 8C
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A
computing device in accordance with the specifications in Subpart J of
Part 15 of FCC rules, which are designed to provide reasonable protection
against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to
cause interference, in which case the user at his own expense will be required
to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.

3
NOM STATEMENT
NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como
sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por los
orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de
calor como radiadores, registros de calor, estufas u otros aparatos
(incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo
del tipo descrito en el instructivo de operación, o como se indique en
el aparato.

4
POW-R-SWITCHES 4C AND 8C
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos
de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo
no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos
no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro
del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra
un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.

5
TABLE OF CONTENTS
Contents
Chapter Page
1. Specifications .................................................................................................6
2. Introduction...................................................................................................8
3. Installation......................................................................................................9
3.1 Mode Switch ........................................................................................9
3.2 Cabling to the Switch ..........................................................................9
3.3 Cable Length .......................................................................................9
3.4 Power Connection...............................................................................9
3.5 Setting the DIP Switch ......................................................................10
3.6 Power Control ...................................................................................11

6
POW-R-SWITCHES 4C AND 8C
Compliance — All models: FCC Class A, DOC Class/MDC classe A;
SWI037AE, SWI038AE: CE (models having IEC power
connectors)
Interface — All voltages over the range of RS-232
Protocol — Asynchronous
Data Format — 8 bits or 7 bits even/odd parity; 600, 1200, 2400, 9600,
19,200, 38,400, 57,600, and 115,200 bps (DIP-switch
selectable)
Flow Control — Transparent to signals through I/O ports
Maximum
Distance — From DB9 connectors to attached devices: 50 feet
(15.2 m); From RJ-11 connector: 4000 feet (1219 m)
unit to unit
User Controls — DCE/DTE slide switch;
DIP switch for data format and rate;
DIP switch for arming code selection;
Reset switch
Indicators — (5) or (9) front-mounted LEDs:
(1) Power, (4) or (8) Output Status
Connectors — All models: (2) DB9 female data connectors
(pass-through) and (2) RJ-11 (expansion);
SWI037A, SWI038A: (4) or (8) NEMA 5-15R
power outlets;
SWI037AE, SWI038AE: (4) or (8) IEC320 power outlets
1. Specifications

7
CHAPTER 1: Specifications
Leads/Signals
Supported — All of the leads on the DB9 connectors
Temperature
Tolerance — 32 to 104˚F (0 to 40˚C)
Humidity
Tolerance — 10 to 90%, noncondensing
Power — Control circuits input through wallmount 5-VDC
supply (included);
Output: Up to 8 amps per output and up to 8 amps
aggregate total
Size — SWI037A, SWI037AE: 2.8"H x 8"W x 6.3"D
(7.1 x 20.3 x 16 cm);
SWI038A, SWI038AE: 1.8"H x 19"W x 8"D
(4.6 x 48.3 x 20.3 cm)
Weight — SWI037A, SWI037AE: 3 lb. (1.4 kg);
SWI038A, SWI038AE: 6.5 lb. (3 kg)

8
POW-R-SWITCHES 4C AND 8C
The code-operated Pow-R-Switches are AC power switches having multiple
outputs and RS-232 control inputs. They detect a pre-selected code sequence
embedded in the data stream and switch the outputs ON or OFF. These
Switches provide pass-through connectors for easy insertion into a data line.
Code-controlled Switches can be daisychained with RJ-11 four conductor
cables (these cables must have straight-through pinning). Individual models
are programmed with unique codes via an 8-position DIP switch, permitting
the individual control of up to 2056 individual outlets (256 arming codes x 8
outlets per unit, 8-port model). 4- and 8-port models can be mixed.
Table 2-1. Available Models
Code Name Type of AC Connector
SWI037A Pow-R-Switch 4C (2) DB9 female, (2) RJ-11,
(4) NEMA 5-15R power outlets
SWI037AE Pow-R-Switch 4C (IEC) (2) DB9 female, (2) RJ-11,
(4) IEC320 power outlets
SWI038A Pow-R-Switch 8C (2) DB9 female, (2) RJ-11,
(8) NEMA 5-15R power outlets
SWI038AE Pow-R-Switch 8C (IEC) (2) DB9 female, (2) RJ-11,
(8) IEC320 power outlets
2. Introduction

9
CHAPTER 3: Installation
IMPORTANT!
Before attaching any cables or power plugs, make sure that the power
is OFF on all equipment, including the Pow-R-Switch.
A serial self-test is included to help you when installing the unit.
3.1 Mode Switch
The DB9 data ports are configured DCE and DTE. This switch reverses the
connections for Tx, Rx, CTS, and DTR. This slide switch is recessed behind
the front panel and is operated through a hole in the panel.
3.2 Cabling to the Switch
Cable(s) with DB9 male connectors are required. The cable(s) must be wired
straight through and pinned for an AT®style 9-pin serial port.
3.3 Cable Length
RS-232 data cables are typically limited to distances of 50 feet (15.2 m) or less
at 19.2 Kbps. Extended distance cables are available to increase this distance.
Actual installed length will depend on the interface, cable type, and data rate.
3.4 Power Connection
Plug the adapter into the Pow-R-Switch. Plug the AC end into a stable source
of 115-volt, 60-Hz power (or 230-volt, 50-Hz power for SWI037AE and
SWI038AE). Add AC connections to the output ports. Connect the power
input cable to the main AC supply.
3. Installation

10
POW-R-SWITCHES 4C AND 8C
3.5 Setting the DIP Switch
Once again, before attaching any cables or power plugs, make sure power to
all equipment is OFF. Select the proper data rate, word structure, and arming
character. Connect the RS-232 connector(s) and plug in the 5-volt DC power
supply. Attach the power cords.
The data rate and word structure can be set by using the chart below. These
selections are made on SW1.
Table 3-1. Possible Settings of the Communications DIP Switch
FUNCTION DIP-SWITCH POSITION*
12345678
Data Rate (bps)
115,200 OFF OFF OFF
57,600 ON OFF OFF
38,400 OFF ON OFF
19,200 ON ON OFF
9600 OFF OFF ON
2400 ON OFF ON
1200 OFF ON ON
600 ON ON ON
Word Structure
8 data bits, no parity OFF OFF
8 data bits, no parity ON OFF
7 data bits, odd parity OFF ON
7 data bits, even parity ON ON
Self-Test
Normal Mode OFF
Run Self-Test ON
*A switch position is ON when it is down (closer to the number that identifies it).
To test your installation, you can use the serial self-test. To enable the self-test,
put switch 6 in the ON position and reset the Pow-R-Switch. To end the self-
test, turn switch 6 OFF.

11
CHAPTER 3: Installation
The self-test message is sent to the output (DCE) port. Note that the self-test
message will not be sent to the DCE port. You can reverse the DTE/DCE
selections of the two DB9 connectors by changing the Mode switch (see
Section 3.1).
3.6 Power Control
Select the arming code by using the DIP switch SW2 mounted at the front
of the unit. Turn power ON by sending the arming character followed by
the port number and a “1” to the Pow-R-Switch. Turn power OFF by sending
the arming character followed by the port number and a “0.” You can query
the present status of a port (ON or OFF) by sending the arming character
followed by the port number and a “#”; the Pow-R-Switch will respond by
returning the arming character, the port number, and a “1” if the port is
ON or a “0” if the port is OFF.
Arming codes and the data rate and format can be changed without removing
power from the unit. Press the Reset switch on the front of the unit after
making these changes.

12
POW-R-SWITCHES 4C AND 8C
Table 3-2. Possible Settings of the Arming-Code DIP Switch
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
00 NUL OFF OFF OFF OFF OFF OFF OFF OFF
01 SOH ON OFF OFF OFF OFF OFF OFF OFF
02 STX OFF ON OFF OFF OFF OFF OFF OFF
03 ETX ON ON OFF OFF OFF OFF OFF OFF
04 EOT OFF OFF ON OFF OFF OFF OFF OFF
05 ENQ ON OFF ON OFF OFF OFF OFF OFF
06 ACK OFF ON ON OFF OFF OFF OFF OFF
07 BEL ON ON ON OFF OFF OFF OFF OFF
08 BS OFF OFF OFF ON OFF OFF OFF OFF
09 HT ON OFF OFF ON OFF OFF OFF OFF
0A LF OFF ON OFF ON OFF OFF OFF OFF
0B VT ON ON OFF ON OFF OFF OFF OFF
0C FF OFF OFF ON ON OFF OFF OFF OFF
0D CR ON OFF ON ON OFF OFF OFF OFF
0E SO OFF ON ON ON OFF OFF OFF OFF
0F Sl ON ON ON ON OFF OFF OFF OFF
10 DLE OFF OFF OFF OFF ON OFF OFF OFF
11 DC1 ON OFF OFF OFF ON OFF OFF OFF
12 DC2 OFF ON OFF OFF ON OFF OFF OFF
13 DC3 ON ON OFF OFF ON OFF OFF OFF
14 DC4 OFF OFF ON OFF ON OFF OFF OFF
15 NAK ON OFF ON OFF ON OFF OFF OFF
16 SYN OFF ON ON OFF ON OFF OFF OFF
17 ETB ON ON ON OFF ON OFF OFF OFF
18 CAN OFF OFF OFF ON ON OFF OFF OFF
19 EM ON OFF OFF ON ON OFF OFF OFF
1A SUB OFF ON OFF ON ON OFF OFF OFF
1B ESC ON ON OFF ON ON OFF OFF OFF
1C FS OFF OFF ON ON ON OFF OFF OFF
1D GS ON OFF ON ON ON OFF OFF OFF
1E RS OFF ON ON ON ON OFF OFF OFF
1F US ON ON ON ON ON OFF OFF OFF
20 SP OFF OFF OFF OFF OFF ON OFF OFF
21 ! ON OFF OFF OFF OFF ON OFF OFF
22 " OFF ON OFF OFF OFF ON OFF OFF
23 # ON ON OFF OFF OFF ON OFF OFF
24 $ OFF OFF ON OFF OFF ON OFF OFF
*A switch position is ON when it is down (closer to the number that identifies it).

13
CHAPTER 3: Installation
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
25 % ON OFF ON OFF OFF ON OFF OFF
26 & OFF ON ON OFF OFF ON OFF OFF
27 ' ON ON ON OFF OFF ON OFF OFF
28 ( OFF OFF OFF ON OFF ON OFF OFF
29 ) ON OFF OFF ON OFF ON OFF OFF
2A * OFF ON OFF ON OFF ON OFF OFF
2B + ON ON OFF ON OFF ON OFF OFF
2C , OFF OFF ON ON OFF ON OFF OFF
2D - ON OFF ON ON OFF ON OFF OFF
2E . OFF ON ON ON OFF ON OFF OFF
2F / ON ON ON ON OFF ON OFF OFF
30 0 OFF OFF OFF OFF ON ON OFF OFF
31 1 ON OFF OFF OFF ON ON OFF OFF
32 2 OFF ON OFF OFF ON ON OFF OFF
33 3 ON ON OFF OFF ON ON OFF OFF
34 4 OFF OFF ON OFF ON ON OFF OFF
35 5 ON OFF ON OFF ON ON OFF OFF
36 6 OFF ON ON OFF ON ON OFF OFF
37 7 ON ON ON OFF ON ON OFF OFF
38 8 OFF OFF OFF ON ON ON OFF OFF
39 9 ON OFF OFF ON ON ON OFF OFF
3A : OFF ON OFF ON ON ON OFF OFF
3B ; ON ON OFF ON ON ON OFF OFF
3C < OFF OFF ON ON ON ON OFF OFF
3D = ON OFF ON ON ON ON OFF OFF
3E > OFF ON ON ON ON ON OFF OFF
3F? ONONONONONONOFFOFF
40 @ OFF OFF OFF OFF OFF OFF ON OFF
41 A ON OFF OFF OFF OFF OFF ON OFF
42 B OFF ON OFF OFF OFF OFF ON OFF
43 C ON ON OFF OFF OFF OFF ON OFF
44 D OFF OFF ON OFF OFF OFF ON OFF
45 E ON OFF ON OFF OFF OFF ON OFF
46 F OFF ON ON OFF OFF OFF ON OFF
47 G ON ON ON OFF OFF OFF ON OFF
48 H OFF OFF OFF ON OFF OFF ON OFF
49 I ON OFF OFF ON OFF OFF ON OFF
4A J OFF ON OFF ON OFF OFF ON OFF
4B K ON ON OFF ON OFF OFF ON OFF
*A switch position is ON when it is down (closer to the number that identifies it).

14
POW-R-SWITCHES 4C AND 8C
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
4C L OFF OFF ON ON OFF OFF ON OFF
4D M ON OFF ON ON OFF OFF ON OFF
4E N OFF ON ON ON OFF OFF ON OFF
4F O ON ON ON ON OFF OFF ON OFF
50 P OFF OFF OFF OFF ON OFF ON OFF
51 Q ON OFF OFF OFF ON OFF ON OFF
52 R OFF ON OFF OFF ON OFF ON OFF
53 S ON ON OFF OFF ON OFF ON OFF
54 T OFF OFF ON OFF ON OFF ON OFF
55 U ON OFF ON OFF ON OFF ON OFF
56 V OFF ON ON OFF ON OFF ON OFF
57 W ON ON ON OFF ON OFF ON OFF
58 X OFF OFF OFF ON ON OFF ON OFF
59 Y ON OFF OFF ON ON OFF ON OFF
5A Z OFF ON OFF ON ON OFF ON OFF
5B [ ON ON OFF ON ON OFF ON OFF
5C \ OFF OFF ON ON ON OFF ON OFF
5D ] ON OFF ON ON ON OFF ON OFF
5E ^ OFF ON ON ON ON OFF ON OFF
5F _ ON ON ON ON ON OFF ON OFF
60 ` OFF OFF OFF OFF OFF ON ON OFF
61 a ON OFF OFF OFF OFF ON ON OFF
62 b OFF ON OFF OFF OFF ON ON OFF
63 c ON ON OFF OFF OFF ON ON OFF
64 d OFF OFF ON OFF OFF ON ON OFF
65 e ON OFF ON OFF OFF ON ON OFF
66 f OFF ON ON OFF OFF ON ON OFF
67 gON ON ON OFF OFF ON ON OFF
68 h OFF OFF OFF ON OFF ON ON OFF
69 i ON OFF OFF ON OFF ON ON OFF
6A j OFF ON OFF ON OFF ON ON OFF
6B k ON ON OFF ON OFF ON ON OFF
6C I OFF OFF ON ON OFF ON ON OFF
6D m ON OFF ON ON OFF ON ON OFF
6E n OFF ON ON ON OFF ON ON OFF
6F o ON ON ON ON OFF ON ON OFF
70 p OFF OFF OFF OFF ON ON ON OFF
71 q ON OFF OFF OFF ON ON ON OFF
72 r OFF ON OFF OFF ON ON ON OFF
*A switch position is ON when it is down (closer to the number that identifies it).

15
CHAPTER 3: Installation
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
73 s ON ON OFF OFF ON ON ON OFF
74 t OFF OFF ON OFF ON ON ON OFF
75 u ON OFF ON OFF ON ON ON OFF
76 v OFF ON ON OFF ON ON ON OFF
77 w ON ON ON OFF ON ON ON OFF
78 x OFF OFF OFF ON ON ON ON OFF
79 y ON OFF OFF ON ON ON ON OFF
7A z OFF ON OFF ON ON ON ON OFF
7B { ON ON OFF ON ON ON ON OFF
7C I OFF OFF ON ON ON ON ON OFF
7D } ON OFF ON ON ON ON ON OFF
7E ~ OFF ON ON ON ON ON ON OFF
7F DEL ON ON ON ON ON ON ON OFF
80 OFF OFF OFF OFF OFF OFF OFF ON
81 ON OFF OFF OFF OFF OFF OFF ON
82 OFF ON OFF OFF OFF OFF OFF ON
83 ON ON OFF OFF OFF OFF OFF ON
84 OFF OFF ON OFF OFF OFF OFF ON
85 ON OFF ON OFF OFF OFF OFF ON
86 OFF ON ON OFF OFF OFF OFF ON
87 ON ON ON OFF OFF OFF OFF ON
88 OFF OFF OFF ON OFF OFF OFF ON
89 ON OFF OFF ON OFF OFF OFF ON
8A OFF ON OFF ON OFF OFF OFF ON
8B ON ON OFF ON OFF OFF OFF ON
8C OFF OFF ON ON OFF OFF OFF ON
8D ON OFF ON ON OFF OFF OFF ON
8E OFF ON ON ON OFF OFF OFF ON
8F ON ON ON ON OFF OFF OFF ON
90 OFF OFF OFF OFF ON OFF OFF ON
91 ON OFF OFF OFF ON OFF OFF ON
92 OFF ON OFF OFF ON OFF OFF ON
93 ON ON OFF OFF ON OFF OFF ON
94 OFF OFF ON OFF ON OFF OFF ON
95 ON OFF ON OFF ON OFF OFF ON
96 OFF ON ON OFF ON OFF OFF ON
97 ON ON ON OFF ON OFF OFF ON
98 OFF OFF OFF ON ON OFF OFF ON
99 ON OFF OFF ON ON OFF OFF ON
*A switch position is ON when it is down (closer to the number that identifies it).

16
POW-R-SWITCHES 4C AND 8C
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
9A OFF ON OFF ON ON OFF OFF ON
9B ON ON OFF ON ON OFF OFF ON
9C OFF OFF ON ON ON OFF OFF ON
9D ON OFF ON ON ON OFF OFF ON
9E OFF ON ON ON ON OFF OFF ON
9F ON ON ON ON ON OFF OFF ON
A0 OFF OFF OFF OFF OFF ON OFF ON
A1 ON OFF OFF OFF OFF ON OFF ON
A2 OFF ON OFF OFF OFF ON OFF ON
A3 ON ON OFF OFF OFF ON OFF ON
A4 OFF OFF ON OFF OFF ON OFF ON
A5 ON OFF ON OFF OFF ON OFF ON
A6 OFF ON ON OFF OFF ON OFF ON
A7 ON ON ON OFF OFF ON OFF ON
A8 OFF OFF OFF ON OFF ON OFF ON
A9 ON OFF OFF ON OFF ON OFF ON
AA OFF ON OFF ON OFF ON OFF ON
AB ON ON OFF ON OFF ON OFF ON
AC OFF OFF ON ON OFF ON OFF ON
AD ON OFF ON ON OFF ON OFF ON
AE OFF ON ON ON OFF ON OFF ON
AF ON ON ON ON OFF ON OFF ON
B0 OFF OFF OFF OFF ON ON OFF ON
B1 ON OFF OFF OFF ON ON OFF ON
B2 OFF ON OFF OFF ON ON OFF ON
B3 ON ON OFF OFF ON ON OFF ON
B4 OFF OFF ON OFF ON ON OFF ON
B5 ON OFF ON OFF ON ON OFF ON
B6 OFF ON ON OFF ON ON OFF ON
B7 ON ON ON OFF ON ON OFF ON
B8 OFF OFF OFF ON ON ON OFF ON
B9 ON OFF OFF ON ON ON OFF ON
BA OFF ON OFF ON ON ON OFF ON
BB ON ON OFF ON ON ON OFF ON
BC OFF OFF ON ON ON ON OFF ON
BD ON OFF ON ON ON ON OFF ON
BE OFF ON ON ON ON ON OFF ON
BF ON ON ON ON ON ON OFF ON
C0 OFF OFF OFF OFF OFF OFF ON ON
*A switch position is ON when it is down (closer to the number that identifies it).

17
CHAPTER 3: Installation
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
C1 ON OFF OFF OFF OFF OFF ON ON
C2 OFF ON OFF OFF OFF OFF ON ON
C3 ON ON OFF OFF OFF OFF ON ON
C4 OFF OFF ON OFF OFF OFF ON ON
C5 ON OFF ON OFF OFF OFF ON ON
C6 OFF ON ON OFF OFF OFF ON ON
C7 ON ON ON OFF OFF OFF ON ON
C8 OFF OFF OFF ON OFF OFF ON ON
C9 ON OFF OFF ON OFF OFF ON ON
CA OFF ON OFF ON OFF OFF ON ON
CB ON ON OFF ON OFF OFF ON ON
CC OFF OFF ON ON OFF OFF ON ON
CD ON OFF ON ON OFF OFF ON ON
CE OFF ON ON ON OFF OFF ON ON
CF ON ON ON ON OFF OFF ON ON
D0 OFF OFF OFF OFF ON OFF ON ON
D1 ON OFF OFF OFF ON OFF ON ON
D2 OFF ON OFF OFF ON OFF ON ON
D3 ON ON OFF OFF ON OFF ON ON
D4 OFF OFF ON OFF ON OFF ON ON
D5 ON OFF ON OFF ON OFF ON ON
D6 OFF ON ON OFF ON OFF ON ON
D7 ON ON ON OFF ON OFF ON ON
D8 OFF OFF OFF ON ON OFF ON ON
D9 ON OFF OFF ON ON OFF ON ON
DA OFF ON OFF ON ON OFF ON ON
DB ON ON OFF ON ON OFF ON ON
DC OFF OFF ON ON ON OFF ON ON
DD ON OFF ON ON ON OFF ON ON
DE OFF ON ON ON ON OFF ON ON
DF ON ON ON ON ON OFF ON ON
E0 OFF OFF OFF OFF OFF ON ON ON
E1 ON OFF OFF OFF OFF ON ON ON
E2 OFF ON OFF OFF OFF ON ON ON
E3 ON ON OFF OFF OFF ON ON ON
E4 OFF OFF ON OFF OFF ON ON ON
E5 ON OFF ON OFF OFF ON ON ON
E6 OFF ON ON OFF OFF ON ON ON
E7 ON ON ON OFF OFF ON ON ON
*A switch position is ON when it is down (closer to the number that identifies it).

18
POW-R-SWITCHES 4C AND 8C
ARMING CODE DIP-SWITCH POSITIONS*
HEX ASCII 12345678
E8 OFF OFF OFF ON OFF ON ON ON
E9 ON OFF OFF ON OFF ON ON ON
EA OFF ON OFF ON OFF ON ON ON
EB ON ON OFF ON OFF ON ON ON
EC OFF OFF ON ON OFF ON ON ON
ED ON OFF ON ON OFF ON ON ON
EE OFF ON ON ON OFF ON ON ON
EF ON ON ON ON OFF ON ON ON
F0 OFF OFF OFF OFF ON ON ON ON
F1 ON OFF OFF OFF ON ON ON ON
F2 OFF ON OFF OFF ON ON ON ON
F3 ON ON OFF OFF ON ON ON ON
F4 OFF OFF ON OFF ON ON ON ON
F5 ON OFF ON OFF ON ON ON ON
F6 OFF ON ON OFF ON ON ON ON
F7 ON ON ON OFF ON ON ON ON
F8 OFF OFF OFF ON ON ON ON ON
F9 ON OFF OFF ON ON ON ON ON
FA OFF ON OFF ON ON ON ON ON
FB ON ON OFF ON ON ON ON ON
FC OFF OFF ON ON ON ON ON ON
FD ON OFF ON ON ON ON ON ON
FE OFF ON ON ON ON ON ON ON
FF ON ON ON ON ON ON ON ON
*A switch position is ON when it is down (closer to the number that identifies it).