H-KING TL2000 User manual

H-KING TL2000 Sports
Plane with Floats or Wheels

TL 2000
INSTRUCTION MANUAL
INTRODUCTION.
The H-King TL2000 EPO RC Plane (PnF) is a fun plane
to fly and has both wheels and floats in the kit so you can
fly off land or water. The wingspan is 1160mm so it can
easily fit in your car for transport to your favorite flying
areas. The TL2000 is built from tough EPO foam so it will
take all the knocks and bangs in its stride.
The TL2000 is a single-engine, two-seat ultralight which
was designed in the Czech Republic. It first flew in 1997
and is a low wing monoplane with a large bubble canopy
for excellent visibility.
The H-King TL2000 comes complete with motor, ESC
and servos pre-fitted to make assembly easy and very
quick. The horizontal stabilizer is glued on but the wings
and the float option are held in place with thumb screws.
The wheel undercarriage is held on with screws and the
nosewheel and water rudder are held in place with grub
screws. All you need to supply is a battery, transmitter
and receiver.
The powerful 2838-1500KV brushless motor combined
with a 3-blade prop has lots of power to do exciting
aerobatics like loops and rolls. It also has fitted a 40 amp
brushless ESC with 3 amp BEC and 4 x 9g servos

SAFETY INSTRUCTIONS
1
1. Please read this manual carefully and follow the instructions
before you use this product.
2. This airplane is not a toy, due to it's advanced flying qualities it
is only suitable for pilots with intermediate or higher experience. If
you are a novice then please only operate with the assistance of
an experienced pilot.
3. Not recommended for children under 14 years old.
4. Please set up this plane according to the instructions and
make sure you keep your hands and other parts of your body out
of the way of the rotating propeller at all times. Failure to do so
will result in damage to yourself and to the airplane.
5. Do not fly in thunderstorms, strong winds or wet weather.
6. Never fly R/C planes where there are overhead power lines,
automobiles, airports, railway lines or near a highway.
7. Never fly R/C planes where there are crowds of people or over
organised games. This airplane requires a very flat landing and
take-off area or lake that is clear of tree's and other obstacles.
Remember safety is the responsibility of the pilot.
8. Do not attempt to catch the plane when you are flying it.
9. The operator will bear the full responsibility of flying and the
proper operation and usage of this model. We at Hobbyking will
not be responsible for any liability or loss due to improper use of
this model.
H-KING

2
TL 2000
Specifications:
Wingspan: 1160mm
Length: 888mm
Motor: 2838-1500KV brushless outrunner
ESC: 40A with 3A BEC brushless
Servos: 4 x 9g digital
Propeller: 8x4.5 3 blade
Weight with Floats: 1020g
Weight with Main Gear and Nosewheel: 940g
Material: EPO
Features:
• Lightweight EPO foam fully molded with scale detail
• Detail cockpit including an instrument panel and factory
applied decals
• Quick build time
• Efficient 3-blade propeller
• High power to weight ratio
• Water floats and rudder (included)
• Main U/C and nosewheel (included)
• Assembly hardware pack (included)
Requires:
1 x 4ch Transmitter or greater
1 x 4ch Receiver or greater
1 x 1300mAh 3S lipoly battery

3
KIT CONTENTS
H-KING

4
TL2000
Step 1: Apply a medium or slow setting CA glue to the slot in the
rear of the fuselage for the horizontal stabilizer.
Step 2: Slide the horizontal stabilizer into place ensuring it remains
square and true to the fuselage while the glue sets. Once the glue
has set run a small bead of glue around the joint to make sure of a
strong assembly.

5
Step 3: If doing the float plane version then follow these steps. If
fitting wheels go to Step 6. Centralize the rudder servo and fit the
water rudder.
Step 4: With the rudder servo central tighten the grub
screw in the water rudder steering collet.
H-KING

6
Step 4: Attach the floats with the 4 supplied thumb screws
Step 5: Finished float assembly.
TL2000

7
TL 2000
Step 6: Put the M3 x 25mm screw through the hole in the bottom
of the aluminum U/C and lock into place using a plain M3 nut.
Repeat for the other side.
Step 6: Slide the wheel over the M3 x 25mm screw and secure the
wheel with a M3 locknut. Repeat this process for the other side.

8
H-KING
Step 7: Remove the battery hatch cover then remove the 2 M3 screws in
the plywood undercarriage mount.
Step 8: Using the M3 screws fit the aluminum undercarriage to the
plywood mount. Note: Straight edge of undercarriage faces
forward.