Canon CREATIVE PARK Temple of the Emerald, Thai User manual

Temple of the Emerald, Thai : Assembly Instructions
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Five A4 sheets (No. 1 to No. 5)
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
* This model was designed for Papercraft and may differ from the original in some respects.
Before starting assembly :
Writing the number of each section on its back side before
cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after
cutting out the sections.) After gluing,cut off or cut out.
Indicates where sections should be
glued together.
[Key points on making the ornamental
parts around the roof edges]
1) Fold along the center line (to give angling) and glue the rear side
2) Cut along the cutting lines (or red lines).
* Do not glue the valley fold parts, but open up to the outside to glue.
[Key points at making the pillar parts]
1) It is easier to fold 2 or 3 pillars in a row on a part sheet.
2) Firmly fold the octagonal folding lines and glue together.
3) After gluing, cut out the pasting
margins at the top and bottom.
Glue on the rear side.
Glue on the
rear side.
Clipping
Clipping

Temple of the Emerald, Thai : Assembly Instructions
Assemble the main body and the first level of the roof.
Lower part
Lower part
Lower
part
Upper part
Upper part
Adhere the tip of
the roof with the glue
on the rear side
Adhere the
tip of the roof
with the glue
on the rear side
Cross section(how to fold)
Image before
gluing
Lower part of
the roof
The same for
the part 17
Give different levels with the sides of the roofs and glue.

Temple of the Emerald, Thai : Assembly Instructions
Assemble the center rooftop and the second level roof.
Big small
(2 pieces)
Glue to the front and rear sides.
Glue on the
rear side
Front of the second level
(same in the rear)
Side of the second level (right)
Side of the second level (left) is
the part

Temple of the Emerald, Thai : Assembly Instructions
Side of the third and fourth
level (the same for right and left)
The uppermost stage
Assemble the third, fourth level roof and the uppermost stage.
Front of the third and fourth level
(same in the rear)
Assemble the “floor” and glue the “fences” on four sides.
Next, assemble the basement, glue the main body on the floor,
and then glue on the basement.
The same for the other side
The same for
the other side
Insert the pillar
Insert the pillar
Fence
FenceFence
Assemble a basement
Reinforce on
the rear side of
the basement.
Roof
Main-body
Floor
Basement
Glue the lower part
of the main body on
the basement.

Temple of the Emerald, Thai : Assembly Instructions
See the key points on making on p.1 in the
assembly manual and assemble octagonal
pillars (5 types). For the 4 “pillars 50” on the
center part of the sides of the “floor”, insert
them (to the rear of the “pasting margin” of
the floor) and glue. Check the tilting and how
they stand, and glue the pillars (top and bottom)
to the specified locations in the following order.
4 pillars 8 pillars 4 pillars 8 pillars 20 pillars
Inserting type No decoration
Top
Exterior
building
Exterior
building
Exterior
building
Fold the pillar ornament (43) into 3
sides and glue to the specified locations
on the upper part of the pillars.
Glue the ornaments (43) to the side of
the pillars facing outside of the building.
Location to glue the roof ornament parts
(the same for the other side)
Insert into the holes
on the “floor”.
Make the parts (37, 38 and
39) after holding the part (35),
and gluing on to the roof.
Fold along
the center line
Glue the
rear sides
Roof
Finished
Nameplate