Black Stone PATIO 1923 User manual

BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
SAFETY ALERT KEY
DANGER
Indicates a hazardous situation
that, if not avoided, will result in
death or serious injury.
CAUTION
Indicates a hazardous situation
that, if not avoided, could result
in minor or moderate injury.
WARNING
Indicates a hazardous situation
that, if not avoided, could result
in death or serious injury.
NOTICE
Indicates information considered
important, but not hazard-
related (e.g. messages related to
property damage).
OWNER’S MANUAL
IMPORTANT:
This instruction manual contains important
information necessary for the proper assembly and safe
use of the appliance.
Read and follow all warnings and instructions before
assembling and using the appliance.
Follow all warnings and instructions when using
the appliance.
Keep this manual for future reference.
Installer/Assembler: Leave these instructions with the consumer.
For the latest version of this manual,
scan this code or visit
BlackstoneProducts.com/support
| CONTACT CUSTOMER SUPPORT BEFORE RETURNING APPLIANCE TO RETAILER.
MODELS:    v19
36" GRIDDLE
AIRFRYER COMBO
TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
USING YOUR BLACKSTONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | IMPORTANT SAFETY INFORMATION
GAS APPLIANCE SAFETY
• The use of alcohol, prescription, or non-prescription drugs may
impair the consumer’s ability to properly assemble or safely
operate the appliance.
• Keep children and pets away from the appliance at all times.
• Have a type BC or ABC fire extinguisher readily available.
DO NOT USE FOR PURPOSES OTHER THAN INTENDED.
• DO NOT use for commercial cooking.
• DO NOT use this appliance as a heater.
WARNING
Improper installation, use, adjustment, alteration, service,
modification, or maintenance can cause injury or property
damage. Refer to this manual.
INSTALLATION MUST CONFORM wITH LOCAL CODES.
In the absence of local codes, installation must conform with
either ANSI Z223.1/NFPA 54, CSA B149.1, or CSA B149.2.
FOR OUTDOOR USE ONLY.
WARNING
•DO NOT store or use gasoline or other flammable liquids
or vapors in the vicinity of this or any other appliance.
•An LPG cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
DANGER
•NEVER operate this appliance unattended.
•If a fire should occur, keep away from the appliance and
immediately call your fire department. DO NOT attempt
to extinguish an oil or a grease fire with water.
Failure to follow these instructions could result in fire or
property damage, personal injury or death.
DANGER
If you smell gas:
•Shut o gas to the appliance.
•Extinguish any open flame.
•Open hood (if applicable).
•If odor continues, keep away from the appliance
and immediately call your gas supplier or your fire
department.
Failure to follow these instructions could result in fire or
property damage, personal injury or death.
ELECTRIC APPLIANCE SAFETY
TO PROTECT AGAINST ELECTRIC SHOCK:
• DO NOT immerse cord or plugs in water or other liquid.
• Unplug from the outlet when not in use and before cleaning. Allow
to cool before putting on or taking o parts.
• DO NOT use an outdoor cooking gas appliance for purposes other
than intended.
• DO NOT operate this appliance with a damaged cord, plug, or after
the appliance malfunctions or has been damaged in any manner.
Contact the manufacturer for repair.
• DO NOT let the cord hang over the edge of a table or touch
hot surfaces.
• Keep any electrical supply cord and the fuel supply hose away from
heated surfaces.
• When connecting, first connect plug to the appliance then into
the outlet.
USE ONLY A GROUND FAULT INTERRUPTER (GFI) PROTECTED CIRCUIT
wITH THIS APPLIANCE.
• This appliance, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes, with
NFPA 70 Canadian Electrical Code, Part I.
• DO NOT remove the grounding plug or use with an adapter
of 2 prongs.
• Use only extension cords with a 3 prong grounding plug, rated for
the power of the equipment, and approved for outdoor use with a
W-A marking.
PELLET GRILL SAFETY
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE
OF THIS PELLET FUEL-BURNING APPLIANCE. FAILURE TO FOLLOw
THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS
AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.
SAVE THESE INSTRUCTIONS.
• Burning wood gives o carbon monoxide which can cause death.
• DO NOT burn wood chips inside homes, vehicles, tents, garages or
any enclosed areas.
• Use only outdoors where it is well ventilated.
MODELS:   
IMPORTANT SAFETY INFORMATION


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALIMPORTANT SAFETY INFORMATION
When using electrical appliances, basic safety precautions should
always be followed including the following:
01. DO NOT touch hot surfaces. Use handles or knobs.
02. To protect against electrical shock DO NOT immerse cord, plugs,
or appliance in water or other liquid.
03. Close supervision is necessary when any appliance is used by
or near children.
04. Unplug from outlet when not in use and before cleaning. Allow
to cool before putting on or taking o parts.
05. DO NOT operate any appliance with a damaged cord or plug or
after the appliance malfunctions or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair, or adjustment.
06. The use of accessory attachments not recommended by the
appliance manufacturer may cause injuries.
07. DO NOT let cord hang over edge of table or counter, or touch hot
surfaces.
08. DO NOT place on or near a hot gas or electric burner, or in a
heated oven.
09. Extreme caution must be used when moving an appliance
containing hot oil or other hot liquids.
10. To disconnect, turn any control to “o’, then remove plug from
wall outlet.
11. DO NOT use appliance for other than intended use.
12. Fuel, such as charcoal briquettes, is not to be used with appli-
ance.
13. Use only on properly grounded outlet.
14. CAUTION:Risk of Electric Shock. Keep extension cord
connection dry and o the ground.
15. The appliance is not to be used by persons (including children)
with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
16. Children should be supervised to ensure that they DO NOT play
with the appliance.
17. For outdoor use only, DO NOT expose to rain.
18. Be sure that handles are assembled and fastened properly.
SAVE THESE INSTRUCTIONS
WARNING
DO NOT operate this appliance unattended.
FOR ExTENSION CORDS:
a.A short power-supply cord is provided to reduce the risk resulting
from becoming entangled in or tripping over a longer cord.
b.Longer power-supply cords or extension cords are available and
may be used if care is exercised in their use.
c.If a longer power-supply cord or extension cord is used:
01. The marked electrical rating of the cord set or extension cord
should be at least as great as the electrical rating of the appli-
ance.
02. The cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or
tripped over unintentionally.
03. The cord set or extension cord should be a grounding-type
3-wire cord.
d.Outdoor extension cords should be used with outdoor use appli-
ances and are surface marked with the suix letter “W” and with a
tag stating “Suitable for use with outdoor appliances.”
e.The connection to an Extension cord should be kept dry and o the
ground.
f. Store appliance indoors when not in use - out of the reach of
children.
g.DO NOT clean this product with a water spray or the like.
IMPORTANT SAFEGUARDS
MODELS:   


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | ASSEMBLY GUIDE MODELS:   
ASSEMBLY GUIDE
PARTS
QTY
1.1
Control knob bezels

1.2a
Electric ignitor

1.2b Electric ignitor wire
(5pcs per set) with
electrode

PARTS
QTY
1.3a
Griddle tubular
burners

1.3b
Gas rail & Valves

1.4 Regulator hose 
1.5 Air fryer control knob
bezel 
PARTS
QTY
1.6
Motor switch

1.7
Air fryer H burner

1.8 Motor assembly 
1.9 Power cord 
2.1 Griddle top 
PARTS
QTY
2.2
Hood

3 7.1
Air fryer drawer front
panels

3 7. 2 Silicone pads (4 pcs
per pack) 
ExPLODED VIEw
PARTS LIST
2.2
45
1
29
33
34
31
43
44
5
2.1
26
25
1.5
1.7
1.6
1.1
1.2a 1.2b
20
3 7.1
37
38
39
46
3 7. 2
16
30
10
8
15
23
24
30
1.3b
1.3a
9
7
11
1.8
1.4
3
13
16
22
27
19
42
41
14
21
28
24
31
17
36
6


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALASSEMBLY GUIDEMODELS:   
1 Griddle body (1 piece) 2 Griddle top & hood (1 piece) 3 Cart base
(1 piece)
4 Matchstick
holder (1 piece)
5 Hood handle
(1 piece)
6 Hood handle
standos (2 pieces)
7 Left-rear leg
(1 piece)
8 Right-rear leg
(1 piece)
9 Left-front leg
(1 piece)
10 Right-front leg
(1 piece)
11 Top cart panel
(1 piece)
12 Back cart panel
(1 piece)
13 Left cart panel
(1 piece)
14 Crossbar
assembly (1 piece)
15 Garbage bag
holder (1 piece)
16 Paper towel
holder (1 piece)
17 Middle cart
panel (1 piece)
18 Right cart panel
(1 piece)
19 Left side shelf
(1 piece)
20 Right side shelf
(1 piece)
21 Hose retainer
(1 piece)
22 LPG hook
(1 piece)
23 LPG support
(1 piece)
24 LPG support
bracket (1 piece)
25 Cutting board
(1 piece)
26 Magnetic strip
(1 piece)
27 Shelf hooks
(3 pieces)
28 Lockable caster
wheels (4 pieces)
29 Control knobs
(5 pieces)
30 Cart drawer
assembly (2 pieces)
31 Cart drawer
front panels (2 pieces)
32 Cart door
(1 piece)
33 Cart door/
drawer handles
(3 pieces)
34 Cart door/
drawer handle bezels
(6 pieces)
35 Motors
(2 pieces)
36 Motor shells and
brackets (2 pieces)
37 Air fryer drawer
assembly (3 pieces)
38 Air fryer drawer
handles (3 pieces)
39 Air fryer drawer
trivets (3 pieces)
40 Power cord
bracket (1 piece)
41 Aluminum
grease cup liner
(1 piece)
42 Grease cup
(1 piece)
43 Hood hinge
lever 1 (2 pieces)
44 Hood hinge
lever 2 (2 pieces)
45 Shelf bracket
(A) (2 pieces)
46 Shelf bracket
(B) (2 pieces)


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | ASSEMBLY GUIDE
ASSEMBLY INSTRUCTIONS
Find a large, clean area to assemble your appliance.
Remove all packing material before assembling.
CAUTION
Sharp edges. Wear gloves while assembling.
NOT INCLUDED (OPTIONAL):
Two (2) D batteries
ELECTRIC REQUIREMENTS:
120V 60Hz
CAUTION
Heavy pieces. Two people should assemble this appliance.
NOTICE
Place appliance on a heat-resistant and flame-resistant
surface while in use.
NOTICE
DO NOT leave the hood closed for more than 10 minutes while
cooking.
NOTICE
•DO NOT mix old and new batteries.
•DO NOT mix alkaline, standard (carbon-zinc) or rechargeable
(ni-cad, ni-mh, etc.) batteries.
NOTICE
DO NOT place items on stabilizing shelf during use.
TOOLS NEEDED:
#3 Phillips head screwdriver &
Adjustable wrench
TOOL NEEDED:
#3 Phillips head screwdriver
TOOL NEEDED:
Adjustable wrench
TOOL NEEDED:
5mm Allen wrench
NOT INCLUDED:
LPG cylinder
Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
LPG cylinder must include collar to
LPG cylinder must include collar to
protect LPG cylinder valve.
protect LPG cylinder valve.
NOT INCLUDED:
17" griddle base
NOT INCLUDED:
22" griddle base
NOT INCLUDED:
AA battery
NOT INCLUDED:
LPG cylinder
Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)
NOT INCLUDED:
One (1) AA battery (for ignition)
Optional four (4) AA batteries
(for the motor)
TOOLS NEEDED:
#3 Phillips head screwdriver &
Adjustable wrench
TOOL NEEDED:
#3 Phillips head screwdriver
TOOL NEEDED:
Adjustable wrench
TOOL NEEDED:
5mm Allen wrench
NOT INCLUDED:
LPG cylinder
Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
LPG cylinder must include collar toLPG cylinder must include collar to
protect LPG cylinder valve.protect LPG cylinder valve.
NOT INCLUDED:
17" griddle base
NOT INCLUDED:
22" griddle base
NOT INCLUDED:
AA battery
NOT INCLUDED:
LPG cylinder
Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)
NOT INCLUDED:
One (1) AA battery (for ignition)
Optional four (4) AA batteries
(for the motor)
ASSEMBLY INSTRUCTIONS
Find a large, clean area to assemble your appliance.
Remove all packing material before assembling.
CAUTION
Sharp edges. Wear gloves while assembling.
NOT INCLUDED (OPTIONAL):
Two (2) D batteries
ELECTRIC REQUIREMENTS:
120V 60Hz
MODELS:   
47 Hardware pack (1 piece)
a.M6x12 screws (24 pieces)
b.M5x10 screws (34 pieces)
c.Long M6 shoulder bolts (4 pieces)
d.M6x15 screws (8 pieces)
e.M5 step bolts (4 pieces)
f. M6 thumbscrews (4 pieces)
g.M6x15 screws (6 pieces)
h.Spares
i. Long M6 step bolts (8 pieces)
j. M5x15 screws (12 pieces)
k.Short M6 step bolts
NOT INCLUDED:
AA battery &
Ten (10) #2032 cell batteries
[a.]
[b.] [c.]
[d.]
[g.]
[i.]
[e.]
[h.]
[j.][k.]
[f.]


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALASSEMBLY GUIDEMODELS:   
STEP 01 Turn the cart base upside down and screw on the four (4)
lockable caster wheels. (Ensure that the wheels are locked before
attaching them.)
STEP 02 Use three (3) M6x12 screws [a.]to attach the left cart panel
to the cart base.
STEP 03 Use five (5) M6x12 screws [a.]to attach the right cart panel
and middle cart panel to the bottom tray. (Note: the magnets should
face the front.)
STEP 04 Use six (6) M5x10 screws [b.]to attach the back cart panel to
the left cart panel, middle cart panel and right cart panel.
STEP 05 Use eight (8) M5x10 screws [b.]to attach the top cart panel
to the left cart panel, middle cart panel and right cart panel.
Push to lockPush to lock
front left door
front left door
hinge pin
hinge pin
[a.]× 3
front left door
front left door
hinge pin
hinge pin
[a.]× 5 [b.]× 6
[b.]× 8


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | ASSEMBLY GUIDE MODELS:   
STEP 06 Use four (4) M6x12 screws [a.]to attach the left-front leg and
left-rear leg to the cart base. (Note: the front leg is shorter than the
rear leg.)
STEP 07 Use four (4) M6x12 screws [a.]to attach the right-front leg
and right-rear leg to the cart base. (Note: the front leg is shorter
than the rear leg.)
STEP 08 Use four (4) M5x10 screws [b.]to attach the crossbar
assembly to the left-front and left-rear legs.
STEP 09 With the help of another person, set the griddle body
upside down. With the help of another person, slide the cart legs
into the slots of the griddle body. Use six (6) M6x12 screws [a.]to
attach the legs to the griddle body. Use four (4) thumb screws [f.]to
attach the legs to the air fryer body. (DO NOT fully tighten screws at
this time.)
[
a.
]× 6
[f.]× 4
[a.]× 4
[b.]× 4
[a.]× 4


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALASSEMBLY GUIDEMODELS:   
STEP 10 With the help of another person, set the griddle on its feet
and tighten the screws.
STEP 11 Unscrew the two (2) M6x12 screws from the right side of the
griddle, then use these screws to attach the power cord bracket to
the right side of the griddle.
STEP 12 Use two (2) M5x10 screws [b.]to attach the paper towel
holder to the right-front leg.
STEP 13 Use two (2) M6x12 screws [a.]to attach one (1) cart door/
drawer handle and two (2) bezels to the cart door.
STEP 14 Attach the cart door assembly to the cart by first ❶❶
inserting the door into the lower door hinge pin, then ❷❷pressing
down and inserting the upper door hinge pin.
[b.]× 2
[a.]× 2
❶
❶
❷
❷


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | ASSEMBLY GUIDE
Make sure the front pins are
seated in the holes, then push
the griddle top back.
❶❶Place the two front pins into
the front locking holes and push
the griddle top back.
❷❷Then, set the two rear pins
into the rear holes.
❶❶Place the two front pins into
the front locking holes and push
the griddle top back.
❷❷Then, set the two rear pins
into the rear holes.
Make sure the front pins are
seated in the holes, then push
the griddle top back.
Make sure the front pins are fully
seated in the holes, then push
the griddle top forward to lock
the griddle in place.
Make sure the front pins are fully
seated in the holes, then push
the griddle top forward to lock
the griddle in place.
MODELS:   
STEP 15 Use seven (7) M5x10 screws [b.]to attach the cart drawer
front panel to the cart drawer body. Repeat this step with the
other drawer.
STEP 16 Use two (2) long step bolts [i.]to attach one (1) cart door/
drawer handle and two (2) bezels to the cart drawer front panel.
Repeat this step with the other drawer.
STEP 17 Pull out the four (4) cart sliding tracks from the middle and
right cart panels. Insert the drawer sliding tracks into the cart tracks.
STEP 18 With the help of another person, place the griddle top and
hood on the griddle body by aligning the four (4) pins to the holes of
the body.
[b.]× 14
[i.]× 4


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALASSEMBLY GUIDEMODELS:   
STEP 19 Use three (3) M6x15 screws [g.]to attach the LPG support
bracket to the left cart panel.
STEP 20 Use one (1) M6x15 screw [g.]to attach the LPG hook to the
left leg assembly. Use one (1) M6x15 screw [g.]to assemble the hose
retainer. Use one (1) M6x15 screw [g.]to attach the LPG support to
the LPG support bracket.
STEP 21 Slide the hood handle into the two (2) hood handle stand-
os. Use four (4) long M6 shoulder bolts [c.]to attach the handle to
the front of the hood.
STEP 22 Attach the four (4) side shelf brackets to the sides of the
body using eight (8) M6x15 screws [d.]. Use one left shelf bracket (A)
and one right shelf bracket (B).
[g.]× 3
[c.]× 4 [d.]× 8
A
A
A
A
B
B
B
B
[g.]× 3


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | ASSEMBLY GUIDE MODELS:   
STEP 23 Unscrew the three (3) M6x8 screws from the side shelf pegs.
Use the (3) M6x8 screws to attach the three (3) side shelf pegs to the
left side shelf.
STEP 24 Thread two (2) short M6 step bolts [k.]into the top holes on
the left side shelf. Repeat with the right side shelf.
STEP 25 Slide the left side shelf onto the side shelf brackets. The
threaded M6 step bolts will hook and hold the shelf.
Use two (2) short M6 step bolts [k.], to secure the shelf to the griddle
body by screwing them into the bottom holes of the bracket.
Repeat this step with the right side shelf.
STEP 26 Attach the drawer handle:
❷ ❷ Use four (4) M5x15 screws [j.]to attach the drawer handle to
the front panel. Be sure to install handle correctly, with the handle
facing down.
❸❸Re-attach the front panel
with the previously removed
thumb screws.
Repeat this step with the other
two (2) drawers.
❶❶Remove the two small thumb
screws from inside the drawer
to remove the front panel of
the drawer.
[k.]× 4
[k.]× 4
[j.]× 4


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALASSEMBLY GUIDEMODELS:   
STEP 27 Place the cutting board onto the right side shelf. STEP 28 Install the control knob batteries:
❶❶For each of the control
knobs, unscrew the two (2) M3x8
screws to open the base.
❷ ❷ Insert two (2) #2032 cell
batteries (not included) into the
battery socket with the positive
+terminal facing inside.
❸❸Reattach the base.
STEP 29 Install the five (5) control knobs by pushing them into place
in the OFF position.
STEP 30 ❶ ❶ Thread two (2) M5x15 step bolts [e.]into the lower holes
of the right legs.
❷❷Use two (2) M5x15 step bolts [e.]to attach the garbage bag
holder to the right legs.
+
+
-
-
❶❶
❷❷
[e.]× 4


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | ASSEMBLY GUIDE
CAUTION
NEVER leave oil exposed in the rain. This can lead to severe
burns.
Place the included hardcover on the burner when not in use
or if it begins to rain.
NOTICE
•Maximum weight on the side shelf is 10 lbs (4.5 kg).
•The side shelf may get hot while appliance is in use.
CAUTION
Grease build-up on the Flame Tamper can catch fire when
heated.
To prevent damage to the unit and/or injury, clean the top of
the Flame Tamper after each use.
NOTICE
DO NOT sit or stand on the table.
NOTICE
•Maximum weight on the tabletop is 100 lbs (45 kg).
•Maximum weight on the inner shelf is 50 lbs (22.5 kg).
•Maximum weight on the side shelf is 10 lbs (4.5 kg).
CAUTION
Handle will get hot while appliance is in use.
DO NOT touch the handle while appliance is hot.
CAUTION
Heavy pieces. Two people should assemble this appliance.
NOTICE
Place appliance on a heat-resistant and flame-resistant
surface while in use.
NOTICE
DO NOT leave the hood closed for more than 10 minutes while
cooking.
NOTICE
•DO NOT mix old and new batteries.
•DO NOT mix alkaline, standard (carbon-zinc) or rechargeable
(ni-cad, ni-mh, etc.) batteries.
NOTICE
DO NOT place items on stabilizing shelf during use.
MODELS:   
STEP 31 Turn the paper towel hanger 90º. STEP 32 Hang the rear grease cup with aluminum foil liner on the
back of the unit.
STEP 34 Proceed to USING YOUR BLACKSTONE. STEP 33 Use the left screw on the logo panel to attach the match
stick holder.


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALUSING YOUR BLACKSTONE
SETTING UP YOUR OUTDOOR SPACE
THIS APPLIANCE MUST ONLY BE USED OUTDOORS.
• DO NOT use this appliance inside buildings, garages, or any other
enclosed area.
• DO NOT install this appliance in or on a boat.
• DO NOT install this appliance in or on a recreational vehicle.
c.Within a partial enclosure that
includes an overhead cover
and three sidewalls, as long as
30% or more of the horizontal
periphery of the enclosure is
permanently open.
b.Within a partial enclosure that
includes an overhead cover
and no more than two side-
walls. The sidewalls may be
parallel, as in a breezeway, or
at right angles to each other.
a.With walls on three sides, but
with no overhead cover.
SHELTERED OUTDOOR AREAS:
All openings must be permanently open; sliding doors, garage doors,
windows or screened openings are not considered as permanent
openings.
An appliance is considered to be outdoors if installed with shelter no
more inclusive than:
MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL.
• DO NOT use this appliance on or under any apartment or condo-
minium balcony or deck.
• DO NOT obstruct the flow of combustion and ventilation air.
• DO NOT operate this appliance any closer than 36 in (1 m) from the
sides and back of the appliance to combustible construction.
A = 36 in (1 m)
A = 36 in (1 m)
• DO NOT use this appliance under overhead combustible
construction.
BEFORE COOKING
CHECK BURNERS
Prior to connection and use, ensure that there is no debris caught in,
or damage to, the head of the gas cylinder, regulator, hose, burner
and burner ports.
Spiders and insects can nest within and clog the burner/venturi tube
at the orifice.
Please reference the Troubleshooting chapter for burner cleaning
instructions.
 WARNING
A clogged burner can
lead to a fire beneath the
appliance.
Burner should be removed
and cleaned whenever
blockages are found.
DANGER
Flammable items can combust if placed near the appliance.
Keep the appliance area clear and free from combustible
materials, aerosol containers, gasoline and other flammable
vapors and liquids.
THE MINIMUM AMBIENT OPERATING TEMPERATURE IS 0°F (-18°C).
Ensure that the gas
rail fuel nozzle orifice is
correctly engaged within the
burner opening.
A
A
A
A
A
A
A
A
A
A
Both ends open
Both ends open
30%
30%
30%
30%
Venturi
Venturi
Air intake
Air intake
Blocked burner
Blocked burner
Fuel nozzle
Fuel nozzle
Burner opening
Burner opening
MODELS:   
USING YOUR BLACKSTONE


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | USING YOUR BLACKSTONE
THE LPG CYLINDER VALVE MUST HAVE:
• Type 1 valve outlet (thread on the outside).
• Safety relief valve.
• UL listed Overfill Protection Device (OPD). This OPD safety feature is
identified by a unique triangular hand wheel.
• Dust cap. LEAK TEST INSTRUCTIONS
• Leak test new and exchanged LPG cylinders BEFORE connecting
to griddle.
• DO NOT smoke during leak test.
• DO NOT use an open flame to check for gas leaks.
• Appliance must be leak tested outdoors in a well-ventilated
area, away from ignition sources such as gas fired or electrical
appliances.
• During leak test, keep appliance away from open flames or sparks.
LEAK TEST: LPG CYLINDER
STEP 01 Use a clean paintbrush
to brush a  mild soap and
water solution onto joint areas of
the LPG cylinder.
(Indicated by arrows in figure 01.)
(Indicated by arrows in figure 01.)
• Leaks are indicated by
growing bubbles.
WARNING
If growing bubbles appear
during leak test, DO NOT use
or move the LPG cylinder.
Immediately contact an LPG
supplier or fire department.
FILLING & ExCHANGE
• Use only those reputable exchange companies that inspect, preci-
sion fill, test and certify their cylinders. LPG dealer must purge new
cylinder before filling.
• Volume of propane in cylinder will vary by temperature.
WARNING
A frosty regulator indicates gas overfill.
Immediately close LPG cylinder valve and call local LPG
dealer for assistance.
• DO NOT release liquid petroleum gas (LPG) into the atmosphere.
• To remove gas from LPG cylinder, contact a certified LPG dealer or
local fire department for assistance.
• Exchange cylinder only for an OPD safety feature-equipped
cylinder.
Your retailer can help you match a replacement LPG cylinder to your appliance.
Your retailer can help you match a replacement LPG cylinder to your appliance.
LPG CYLINDER REQUIREMENTS
FOR 20 LB (9 KG CYLINDERS)
• The LPG supply cylinder to be used must be constructed and
marked in accordance with the specifications for LP gas cylin-
ders, U.S. Department of Transportation (DOT) or the Standard for
Cylinders, Spheres and Tubes for the Transportation of Dangerous
Goods, CAN/CSA-B339.
• Only LPG cylinders marked “propane” shall be used.
• The LPG cylinder supply system must be arranged for vapor
withdrawal.
•
•
Always keep new LPG cylinders in upright position during use, transit or
Always keep new LPG cylinders in upright position during use, transit or
storage.
storage.
•
•
Always keep the ventilation opening(s) of the cylinder enclosure free and
Always keep the ventilation opening(s) of the cylinder enclosure free and
clear from debris.
clear from debris.
STORING LPG CYLINDERS
WARNING
•DO NOT store a spare LPG cylinder under or near this
appliance.
•DO NOT fill an LPG cylinder beyond 80% full.
If the information above is not followed exactly, a fire causing
death or serious injury may occur.
• The LPG cylinder must be turned OFF when the appliance is
not in use.
• LPG cylinders must be stored outdoors and out of the reach
of children.
• DO NOT store an LPG cylinder inside a building, garage, or any other
enclosed area.
The seal on the type 1 valve outlet could, over time, show marked and
visible damage or deterioration that might cause a leak even with
the connection tightened.
• A visual inspection for the seal must be carried out every time a
LPG cylinder is replace or refilled.
• Any LPG cylinder showing signs of damage or deterioration as
those illustrated including visible cracks and pitting, must be
returned unused to the seller.
FITTINGS & HOSES
• Annual checking and tightening of metal fittings is recommended.
• Keep the fuel supply hose away from any heated surfaces.
• Before each use, check to see if hoses are cut or worn.
• Replace damaged hose before using appliance.
(Use only Blackstone approved valve, hose, or regulator. Failure to comply will
(Use only Blackstone approved valve, hose, or regulator. Failure to comply will
void the warranty.)
void the warranty.)
LPG cylinder valveLPG cylinder valve
Safety relief
Safety relief
valve
valve
OPD hand wheel
OPD hand wheel
Type 1 valve outlet
Type 1 valve outlet
(check seal before use)
(check seal before use)
GOOD SEALGOOD SEAL
BAD SEALBAD SEAL
Dust cap
Dust cap
figure 01
figure 01
MODELS:   


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALUSING YOUR BLACKSTONE
CONNECT THE LPG CYLINDER
ONLY USE A 20 LB (9 KG) CYLINDER
STEP 01 Turn the control
knobs to OFF.
❶
❶Ensure that the LPG cylinder
is OFF by turning the OPD hand
wheel clockwise to a full stop.
❷
❷Remove the safety cap from
the Type 1 valve outlet.
STEP 02 Hold the regulator in a
straight line with the Type 1 valve
outlet so as not to cross thread
the connection.
Center and insert the regu-
lator nipple into the Type 1
valve outlet.
Hand-tighten the coupling nut in
a clockwise direction.
(DO NOT use tools to connect.)
If connection cannot be completed,
If connection cannot be completed,
disconnect regulator and repeat this
disconnect regulator and repeat this
step.
step.
LEAK TEST: VALVES, HOSE & REGULATOR
STEP 01 Turn the control knobs to OFF.
STEP 02 Connect the regulator to the LPG cylinder.
STEP 03 Completely open the LPG tank by turning the OPD hand
wheel counterclockwise.
• If you hear a rushing sound, turn gas o immediately. There is a
major leak at the connection.
• Immediately close the LPG cylinder by turning the OPD hand wheel
clockwise and re-tighten connections. If leaks cannot be stopped
DO NOT TRY TO REPAIR.
STEP 04 Use a clean paintbrush
to brush a  mild soap and
water solutionn onto joint areas
of valves and regulator.
(Indicated by arrows in figure 02.)
(Indicated by arrows in figure 02.)
• Leaks are indicated by
growing bubbles.
• Immediately close the LPG
cylinder by turning the OPD
hand wheel clockwise and
re-tighten connections.
WARNING
If leaks cannot be stopped, DO NOT try to repair.
Regulator must be replaced with a Blackstone approved
model by a professionally licensed, authorized dealer.
The safety relief valve must face
away from the user while the
appliance is in use.
DISCONNECTING THE LPG CYLINDER
STEP 01 Ensure that the control knobs are turned to OFF.
❶
❶Ensure that the LPG cylinder
is OFF by turning the OPD hand
wheel clockwise to a full stop.
❷
❷Turn the coupling nut count-
er-clockwise by hand to remove
the regulator. (DO NOT use tools
to disconnect.)
STEP 02 Place dust cap on LPG
cylinder valve outlet whenever
cylinder is not in use.
Only install the type of dust cap on
Only install the type of dust cap on
cylinder valve outlet that is provided
cylinder valve outlet that is provided
with the cylinder valve. Other types of
with the cylinder valve. Other types of
caps or plugs may result in leakage of
caps or plugs may result in leakage of
propane.
propane.
REGULATOR SAFETY
• Use this appliance, as purchased, only with gas and regulator/
valve assembly supplied. DO NOT use quick connect fittings or
other add-ons.
• DO NOT cross thread (force at an improper angle) the connection
between your LPG cylinder and regulator.
• If you can not connect the regulator, DO NOT use the regulator.
Regulator must be replaced with a Blackstone approved model by a profession-
Regulator must be replaced with a Blackstone approved model by a profession-
ally licensed, authorized dealer.
ally licensed, authorized dealer.
❶❶
❷
❷
Coupling nutCoupling nut
Regulator nippleRegulator nipple
figure 02
figure 02
❶❶
❷
❷
STEP 03 Secure the LPG cylinder
to the appliance by hanging it on
the LPG hook so that it nestles
against the LPG support.
MODELS:   


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | USING YOUR BLACKSTONE
Turn gas ON by turning the gas
cylinder handwheel counter-
clockwise 1 to 3 turns.
2. BATTERY POwERED IGNITION
DO NOT lean over the appliance while lighting.
STEP 01 Insert one (1) AA
battery (not included) under the
ignitor button.
Screw the button into place over
the positive terminal.
STEP 02
❶
❶ Turn the control knob to OFF.
STEP 03
❷
❷Push and hold the ignitor button.
❸
❸Push and turn the control knob counter-clockwise to HIGH.
(Release the ignitor button when the burner lights.)
❹
❹Adjust the temperature to desired level.
IGNITION INSTRUCTIONS
1. CHECK VALVES
STEP 01 Turn knob to OFF position.
STEP 02 Push in knob and release. Knob should spring back.
If knobs
If knobs
DO NOT
DO NOT
spring back, replace valve assembly before using appliance.
spring back, replace valve assembly before using appliance.
STEP 03 Rotate knob to LOW then turn back to OFF. Knob should
turn smoothly.
 WARNING
If burner does not ignite with open gas supply valve, gas
will continue to flow out of burner and could accidentally/
inadvertently ignite with risk of injury.
Ensure gas is o at the supply shut o valve before checking
appliance valves.
❷
❷
❸
❸
❶
❶
❹
❹
1 to 3 turns1 to 3 turns
❶
❶
❷
❷
❸
❸
❶❶
❷❷
❸❸
HEALTHY FLAME PATTERN YELLOw OR IRREGULAR
3. ALwAYS CHECK BURNER FLAME BEFORE USE.
STEP 01 Light burners and rotate knobs from HIGH to LOW.
STEP 02 Look below the cooking surface to view burners. When knob
is at HIGH, flames should be larger than when knob is at LOW.
3. ALwAYS CHECK BURNER FLAME BEFORE USE.
STEP 01 Light burner and rotate knob from LOW to HIGH.
STEP 02 Look below the turntable to view burner. When knob is at
HIGH, flames should be larger than when knob is at LOW.
❶
❶
Flickers of yellow color.
Flickers of yellow color.
❷
❷
Dark blue color.
Dark blue color.
❸
❸
Vibrant blue.
Vibrant blue.
If there is a sudden drop or low
If there is a sudden drop or low
flame issue, please reference the
flame issue, please reference the
Troubleshooting chapter.
Troubleshooting chapter.
IF IGNITION DOES NOT OCCUR IN 5 SECONDS:
STEP 01 Turn the burner control knob OFF.
STEP 02 Wait 5 minutes.
STEP 03 Repeat the lighting procedure.
If burner does not ignite, please reference the Troubleshooting chapter.
If burner does not ignite, please reference the Troubleshooting chapter.
IF IGNITION DOES NOT OCCUR IN 5 SECONDS:
STEP 01 Turn the burner control knob OFF.
STEP 02 Wait 5 minutes.
STEP 03 Repeat the lighting procedure.
If burner does not ignite, please reference the Troubleshooting chapter.If burner does not ignite, please reference the Troubleshooting chapter.
HEALTHY FLAME PATTERN YELLOw OR IRREGULAR
❶ ❶ Flickers of yellow color.Flickers of yellow color.
❷ ❷ Dark blue color.Dark blue color.
❸ ❸ Vibrant blue.Vibrant blue.
If there is a sudden drop or lowIf there is a sudden drop or low
flame issue, please reference theflame issue, please reference the
Troubleshooting chapter.Troubleshooting chapter.
MODELS:   


BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALUSING YOUR BLACKSTONE
wHAT OIL IS BEST TO USE?
• Blackstone Seasoning and
Cast Iron Conditioner.
• Any plant-based cooking oil.
• Rendered animal fat with no
additives.
wASHING YOUR GRIDDLE TOP BEFORE FIRST USE
SEASONING YOUR GRIDDLE
STEP 01 Wipe any debris o
griddle top.
GRIDDLE SEASONING INSTRUCTIONS
STEP 02 Set your griddle to
high heat until your griddle top
changes color. (~10 min)
STEP 04 The griddle top is ready
for another layer of oil when it
stops smoking. Repeat STEP 03
3-4 times, or until the griddle
surface is black.
SEASONING TROUBLESHOOTING
THERE IS A BROwNISH RESIDUE ON THE GRIDDLE SURFACE:
VIDEO TUTORIAL
How to Season a New Blackstone Griddle
youtube.com/watch?v=VspmDVnj2pI&t=3s
STEP 03 Use tongs to hold a
paper towel or cotton cloth and
spread 2-3 tablespoons of your
seasoning oil across the entire
griddle top.
When seasoning your griddle top,
When seasoning your griddle top,
remember to use a thin and even layer
remember to use a thin and even layer
of oil—the thinner the layer of oil, the
of oil—the thinner the layer of oil, the
easier it will be to burn it o.
easier it will be to burn it o.
VIDEO TUTORIAL
Recovering your Blackstone Griddle Top
youtube.com/watch?v=thPE2IgnSiI
PREVENTING RUST
Use your griddle frequently. Every time you cook, you are adding to
the seasoning, which makes rust less likely.
NOTICE
If you live in a humid or coastal climate, your griddle may
require more frequent seasonings between uses.
If rust appears on the griddle surface, rub it o with steel wool, low
grit sandpaper or the Blackstone Pumice Stone and re-season
the surface.
THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:
After using your griddle for multiple cooks, the seasoning will even
out and improve.
POSSIBLE CAUSES SOLUTION
•Too much oil was used.
•You turned o the heat too
soon.
STEP 01 Turn your griddle on high
and let it heat for 10-15 minutes.
STEP 02
Scrape o as much
of the thickened and partially
cooked oil as you can.
STEP 03
Re-season with a very
thin layer of oil.
CAUTION
Properly dispose of the rags/towels used to spread oil on
your griddle top for seasoning purposes to prevent fires that
might occur due to spontaneous combustion.
Under the right conditions, residual oil on rags or towels can oxidize long
Under the right conditions, residual oil on rags or towels can oxidize long
after being removed from a heat source. The oxidation process itself produces
after being removed from a heat source. The oxidation process itself produces
heat which, if not dissipated, can build up and cause combustible materials
heat which, if not dissipated, can build up and cause combustible materials
(including the rags/towels themselves) to ignite.
(including the rags/towels themselves) to ignite.
NOTICE
Soap will ruin a seasoned
griddle. This is the only time
you should use soap on the
griddle cooking surface.
STEP 01 Wash the griddle
cooking surface with hot,
soapy water.
STEP 02 Rinse and dry
completely.
MODELS:   


ENGLISH
BLACKSTONEPRODUCTS.COM/SUPPORT
OWNER’S MANUAL | USING YOUR BLACKSTONE
USING YOUR AIR FRYER
LPG AIR FRYER IGNITION
STEP 03
❶
❶ Turn the fryer control
knob to OFF.
STEP 04 Turn gas ON by turning
the gas cylinder handwheel
counterclockwise 1 to 3 turns.
STEP 02 Insert one (1) AA
battery (not included) under the
ignitor button.
Screw the button into place over
the positive terminal.
STEP 05
❷
❷Push and hold the
ignitor button.
❸
❸Push and turn the fryer
control knob counter-clock-
wise to MAX.
(Release the ignitor button when
the burner lights.)
❹
❹Adjust the temperature to
desired level.
STEP 01 Plug power cord into wall outlet.
STEP 06 Push the rocker switch
to power ON, the blower fan will
start immediately.
To verify that the air fryer burner has lit, look into the burner chamber
from the side of the unit.
❷
❷
MATCH LIGHTING INSTRUCTIONS
If you can not ignite the air fryer with the control knob:
STEP 01 Turn control knob to OFF position.
STEP 04 Push in and turn the control knob to start gas flowing.
Ensure burner lights and stays lit.
STEP 02 Pinch a match into
the match lighter stick. Light
the match.
STEP 03 Guide the flame into
the burner hole until it touches
the burner.
1 to 3 turns1 to 3 turns
❸
❸
❶
❶
❹
❹
CLEANING YOUR AIR FRYER
• DO NOT clean with alcohol or any other flammable substance.
• DO NOT clean the air fryer unit with a water spray or the like.
CLEANING YOUR AIR FRYER BASKET
Your air fryer basket is dishwasher safe, but the handle
assembly is not.
(Basket design may vary depending on appliance.)
(Basket design may vary depending on appliance.)
STEP 01 Loosen the upper thumb screws in the air fryer drawer.
STEP 02 Lift and remove the handle assembly. (DO NOT remove the
thumb screws.)
STEP 03 Remove the trivet from the air fryer basket.
STEP 04 Keep the handle assembly with your appliance.
Reassemble the drawer after the basket is clean and dry.
AIR FRYER SAFETY
• Remove items below the air fryer before operating.
• Blow out drawers before cooking to keep passageways clean.
• Wrap the power cord around the power cord bracket when the air
fryer is not in use.
wHILE IN USE
• DO NOT restrict the flow of the combustion air or the hot
exhaust gasses.
• DO NOT place fryer drawers on griddle surface.
• DO NOT place fryer drawers on or near a hot gas or electric burner,
or in a heated oven.
FOOD
• DO NOT cook food in the fryer without the drawer in place.
• DO NOT add liquids (water or sauces) to hot food in the drawer as it
may flash to steam and cause burns.
COOKING SPRAY
Cooking spray will degrade the non-stick coating. We recommend
using regular cooking oil in a spray bottle.
BLACKBERRY SCONES
Air fryerAir fryer
JALEPEÑO POPPERS
Air fryerAir fryer
THYME CHICKEN wINGS
Air fryerAir fryer
MODELS:   
