Blackbird 43395 User manual

4K 6x2 HDMI® Matrix with Audio
P/N 43395
User's Manual

2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra
attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
•This device is intended for indoor use only.
•Do not expose this device to water or moisture of any kind.
Do not place drinks or other containers with moisture on or
near the device. If moisture does get in or on the device,
immediately remove it from its power source and allow it to
fully dry before reapplying power.
•Do not touch the device, the power cord, or any other
connected cables with wet hands.
•Do not expose this device to excessive vibration, extreme
force, shock, or fluctuations in temperature or humidity.
•Do not expose this device to excessively high temperatures.
Do not place it in, on, or near a heat source, such as a
fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
•Clean using a soft, dry cloth only. Do not use chemical
cleaners, solvents, or detergents. For stubborn deposits,
moisten the cloth with warm water.
•This device has no user serviceable parts. Do not attempt to
open, service, or modify this device.

3
INTRODUCTION
This 4K 6x2 HDMI® Matrix allows you to independently distribute any
of six HDMI inputs to two HDMI outputs. It supports video resolutions
up to 4K@30Hz, including 1080p@60Hz and 3D video . The audio
associated with either output can be extracted and sent to an
external amplifier or powered speakers using the analog 3.5mm,
digital coaxial, or digital optical (Toslink®) audio outputs. Output A
supports the Audio Return Channel (ARC) HDMI feature, which allows
audio originating from the connected television to be distributed to
the audio outputs. It supports a Picture-in-Picture (PiP) mode when
the output resolution is 4K@30Hz and includes an IR remote control.

4
FEATURES
•Independently distributes up to six HDMI® inputs to two
HDMI outputs
•Supports video resolutions up to 4K@30Hz, including
1080p@60Hz and 3D video
•9.0 Gbps video bandwidth
•Supports up to 36-bit Deep Color
•Supports HDCP™ 1.4
•Includes analog 3.5mm stereo, digital coaxial, and digital
optical (Toslink®) audio outputs
•Output A supports the Audio Return Channel (ARC) HDMI
feature
•Supports the Consumer Electronics Control (CEC) HDMI
feature
•Supports 2.0, 5.1, and 7.1 channel audio, including Dolby
TrueHD™ and DTS-HD Master Audio™
•Supports a Picture-in-Picture (PiP) mode when the output
resolution is 4K@30Hz
•Includes an IR remote control

5
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to
ensuring that your ordering, purchasing, and delivery experience is
second to none. If you have any problem with your order, please give
us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our
website www.monoprice.com or via email at
[e-mail]. Check the website for support times and
links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have
all the items listed below. If anything is missing or damaged, please
contact Monoprice Customer Service for a replacement.
1x 6x2 HDMI® Matrix
1x IR Remote Control
1x AC Power Adapter
1x User's Manual

6
PRODUCT OVERVIEW
Remote Control
1. Power Button: Press the Power
Button to turn the matrix on or
to put it into standby mode.
2. Audio Button: Press the Audio
Button to cycle through the
available audio output modes.
The cycle order is 2.0, 5.1, and 7.1.
3. ARC Button: Press the ARC
Button to turn the Audio Return
Channel (ARC) feature on or off.
Only Output A supports ARC and
the connected television must support ARC.
4. PiP Section: Press the PiP Button to turn the Picture-in-Picture
(PiP) mode on or off. PiP is supported only when the output
resolution is 4K@30Hz. Press the Select Button to cycle
through the inputs for the PiP window. Once the desired
input for the PiP window is displayed, press the Enter Button
to confirm the selection.
5. OUT A Section: Press one of the numbered buttons to directly
select one of the six inputs to distribute to Output A.
6. OUT B Section: Press one of the numbered buttons to directly
select one of the six inputs to distribute to Output B.

7
7. Audio Section: Press the OUT A Button to extract the audio
from Output A to the audio outputs. Press the OUT B Button
to extract the audio from Output B to the audio outputs.
Press the A↔B Button to swap the Output from which audio
is extracted.
Matrix
8. INPUT 5/INPUT 6: Two HDMI® ports for connecting HDMI
video source devices.
9. INPUT INDICATORS: Two rows of six LEDs each, labeled Aand
B. One of the LEDs on each row illuminates to indicate the
selected input for each output.
10. AUDIO INDICATORS: Four LEDs indicate whether ARC is on or
off, and the selected audio mode (2.0, 5.1, 7.1). When the ARC
LED is on, the audio from the television connected to output
A is being sent to the STEREO, COAXIAL, and TOSLINK®

8
outputs. The 2.0,5.1, or 7.1 LED illuminates to indicate the
selected audio mode.
11. IR: IR "eye" for receiving signals from the included IR remote
control.
12. OUTPUT A: Press the button to cycle through the available
inputs for Output A.
13. OUTPUT B: Press the button to cycle through the available
inputs for Output B.
14. ARC: Press the button to turn ARC on or off. When ARC is on,
the ARC LED in the AUDIO INDICATORS section illuminates.
15. AUDIO: Press the button to cycle through the three audio
modes (2.0, 5.1, 7.1). The corresponding LED in the AUDIO
INDICATORS section illuminates to indicate the selected audio
mode.
16. RESET: Press the button to reset the matrix to its factory
default settings.
17. POWER: The LED illuminates when the matrix is powered on.
18. DC/5V: DC barrel connector for connecting the included AC
power adapter.
19. HDMI 1/HDMI 2/HDMI 3/HDMI 4: Four HDMI® ports for
connecting HDMI video source devices.
20. OUTPUT B: HDMI port for connection an HDMI display.

9
21. OUTPUT A: HDMI port for connecting an HDMI display.
OUTPUT A supports the ARC feature.
22. STEREO: 3.5mm 2-channel analog audio output jack for
connecting an external amplifier or powered speakers. When
the audio mode is set to 5.1 or 7.1, there will be no sound on
this output.
23. COAXIAL: Digital coaxial audio output for connecting an
external amplifier. If the amplifier does not support the
selected audio format (e.g., Dolby TrueHD™, DTS-HD Master
Audio™, etc.), there will be no sound on this output.
24. TOSLINK: Digital optical audio output for connecting an
external amplifier. If the amplifier does not support the
selected audio format (e.g., Dolby TrueHD™, DTS-HD Master
Audio™, etc.), there will be no sound on this output.

10
SAMPLE CONNECTION DIAGRAM
CONNECTION
Perform the following steps to connect the matrix to your system.
1. Ensure that all devices to be connected are powered off and
disconnected from their power sources.

11
2. Using a High Speed HDMI® Cable (available separately), plug
one end into an HDMI input on one of your displays, then
plug the other end into the OUTPUT A port on the matrix. If
you want to use the ARC feature, you must connect to an
input that supports ARC.
3. Using a High Speed HDMI® Cable (available separately), plug
one end into an HDMI input on your second display, then plug
the other end into the OUTPUT B port on the matrix.
4. (Optional) Using a digital optical (Toslink®) cable (available
separately), plug one end into the digital optical input on your
amplifier, then plug the other end into the TOSLINK port on
the matrix.
5. (Optional) Using a digital coaxial cable (available separately),
plug one end into the digital coaxial input on your amplifier,
then plug the other end into the COAXIAL port on the matrix.
6. (Optional) Using a 3.5mm audio cable (available separately),
plug one end into your amplifier or powered speakers, then
plug the other end into the STEREO jack on the matrix.
7. Using a High Speed HDMI Cable (available separately), plug
one end into one of the HDMI inputs on the matrix, then plug
the other end into the HDMI output on one of your video
source devices. Repeat for up to five additional video source
devices.

12
8. Plug one end of the included AC power adapter into the
DC/5V connector on the matrix, then plug the other end into
a nearby AC power outlet.
9. Pull the film out of the remote control to allow its battery to
connect to the battery terminal.
10. Aim the remote control at the IR "eye" on the matrix, then
press the Power Button on the remote to turn the matrix on.
11. Plug in and power on all connected equipment. Use the
controls on the remote control to switch to each input for
each output to verify that the system is connected properly.
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to
assist you with any questions you may have about installation, setup,
troubleshooting, or product recommendations. If you ever need
assistance with your new product, please come online to talk to one
of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website
www.monoprice.com or through email by sending a message to
[e-mail]. Check the website for support times and links.
To download the latest drivers, firmware, manuals, etc., go to
www.monoprice.com and type the P/N into the search bar. If
available, support files are linked at the bottom of the product page.

13
SPECIFICATIONS
P/N
43395
Video Inputs
6x HDMI®
Video Outputs
1x HDMI with ARC, 1x HDMI
Audio Outputs
1x .3.5mm stereo analog,
1x digital coaxial,
1x digital optical (Toslink®)
Maximum Video Resolution
4K@30Hz, including 1080p and
3D video
Video Bandwidth
9.0Gbps/900MHz total
3.0GHz/300MHz per channel
Input Power
5 VDC
AC Power Adapter Input Power
100 ~ 240 VAC, 50/60 Hz
Maximum Power Consumption
5 watts
Operating Temperature
+32 ~ +158°F (0 ~ +70°C)
Operating Humidity
10 ~ 85% RH, noncondensing
Storage Temperature
+14 ~ +176°F (-10 ~ +80°C)
Storage Humidity
5 ~ 90% RH, noncondensing
Dimensions
9.3" x 2.6" x 1.1"
(210 x 66 x 27 mm)
Weight
12.9 oz. (366g)

14
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Modifying the equipment without Monoprice's authorization may
result in the equipment no longer complying with FCC requirements
for Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be
required to correct any interference to radio or television
communications at your own expense.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off

15
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.

16
Monoprice™, Blackbird™, the Blackbird logo, and all Monoprice logos
are trademarks of Monoprice Inc.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
HDCP™ is a trademark of Digital Content Protection LLC.
TOSLINK® is a registered trademark of Toshiba Corporation.
Dolby®, Dolby® TrueHD™, Dolby Audio™, and the double-D symbol are
trademarks of Dolby Laboratories.
DTS®, the Symbol, and DTS and the Symbol together are registered
trademarks of DTS, Inc. DTS-HD™ and DTS-HD Master Audio™ are
trademarks of DTS, Inc.