BlackVue DMC200 User manual

DR750-2CH LTE
instagram.com/BlackVueofficial
©21
DMC200
User Guide
(Driver Monitoring System)
Cloud Dashcam with Driver Monitoring System
DMS

For manuals, customer support and FAQs go to www.blackvue.com
BLACKVUE
DMC200

DMC200 3
In the box (DR750X DMS Plus / DR900X DMS Plus Package)
Check the box for each of the following items before installing the BlackVue dashcam.
Front camera DMS camera
Front camera
Cigarette
Lighter power cable
(3p)
Front camera
Hardwiring power
cable (3p)
DMS connection
cable
DMS Hardwiring
power cable (2p)
microSD card microSD card reader
Quick start guide
Double-sided tape
for the Mounting
Brackets
Pry tool Cable clips (8 EA)
Need help?
Download the manual (including FAQs) and the latest firmware from www.blackvue.com
Or contact a Customer Support expert at [e-mail]
ENGLISH ENGLISH

4BLACKVUE
In the box (For DR750X DMS LTE Plus Package)
Check the box for each of the following items before installing the BlackVue dashcam.
Front camera DMS camera
Front camera
Cigarette
Lighter power cable
(2p)
DMS Hardwiring
power cable (2p)
DMS connection
cable
DMS Cigarette
Lighter power cable
(2p)
Quick start guide Pry tool
Double-sided tape
for the Mounting
Brackets
Cable clips (8 EA)
SIM eject tool microSD card reader
microSD card SIM card (optional)
Need help?
Download the manual and the latest firmware from www.blackvue.com
Or contact a Customer Support expert at [e-mail]

DMC200 5
At a glance
The following diagrams explain each part of the BlackVue DMS camera.
Indicator LED
: Light Blue in Calibration
: Light Green in Normal mode
: When DMS event detected, Light Red is turned on
IR LED (Inside)
Mounting bracket
Camera lens (Inside)
115
37
Push button
Front camera connection port
DC in
Turn on/off audio beep
ENGLISH ENGLISH

6BLACKVUE
Install and power up
Install the front camera behind the rear view mirror. Install the DMS camera on the
driver‘s dashboard or front windshield.
Remove any foreign matter and clean and dry the installation area before setup.
Front camera DMS camera
Note
yDepending on the mounting position of the product, DMS functions may not
operate normally.
Warning
yDo not install the product in a location where it can obstruct the driver's field
of vision.
yBe careful not to interfere with the product when operating the vehicle
handle.

DMC200 7
Turn off the engine. Open the cover of the microSD card slot, gently push the
card into the slot until it locks into place and close the cover.
Peel off the protective film from the double-sided tape and attach the front
camera to the windshield behind the rear-view mirror.
Adjust the angle of the lens by rotating the body of the front camera. We
recommend pointing the lens slightly downwards (≈10° below horizontal), so as
to record video with a 6:4 road to background ratio.
Note
yRecorded videos from DMS are saved to the microSD card on the front
dashcam.
yFor DR750X DMS LTE Plus users, please insert the SIM card following QSG
that's included in the box.
ENGLISH ENGLISH

8BLACKVUE
Adjust the angle of the lens by rotating body of DMS and mounting bracket and
peel off the double-sided tape.
Attach the DMS camera to the windshield or dashboard. Attach the DMS
camera to the windshield or dashboard.
GOODGOOD BEST
GOOD GOOD
BEST
Windshield Installation Dashboard Installation
Note
yFor best accuracy of DMS, install the DMS camera in the recommended area.

DMC200 9
Connect the front camera ('Rear' port) and the DMS camera(‘V’ out) using the
DMS camera connection cable.
Use the pry tool to lift the edges of the rubber window sealing and or molding
and tuck in the DMS camera connection cable.
DMS camera
connection cable
Connect the DMS camera (DC in) using DMS camera hardwiring cable (2p) to a
car fuse, For details, Skip to for DMS Hardwiring Power cable setup.
ENGLISH ENGLISH

10 BLACKVUE
Use the pry tool to lift the edges of the rubber window sealing and or molding
and tuck in the DMS camera Hardwiring power cable.
DMS camera
connection cable
Power cord cable
DMS camera
Hardwiring cable
Plug the cigarette lighter power cable into the cigarette lighter socket and
the front camera. Skip to for Hardwiring Power Cable setup (DR750X Plus,
DR900X Plus only).
Locate the fuse box to connect the hardwiring power cable.
Note
yLocation of the fuse box differ by manufacturer or model. For details, refer to
the vehicle owner's manual.
yIf you want to use cigarette lighter power cable for DMS camera, plug the
cigarette lighter power cable (2p) into cigarette socket.

DMC200 11
- 1After removing fuse panel cover, find a fuse that powers on when engine
is turned on (ex. cigarette lighter socket, audio, etc) and another fuse that
remains powered on after the engine is turned off (ex. hazard light, interior
light). Connect the ACC+ cable to a fuse that powers on after engine
start (Front camera hardwiring cable (3p)) and BATT+ cable to a fuse that
remains powered on after engine is turned off (Front camera hardwiring
cable (3p) + DMS camera hardwiring cable (2p)).
Front camera hardwiring cable (3p) DMS camera hardwiring cable (2p)
- 2Connect the GND cable to metal ground bolt (Front camera hardwiring
cable (3p) + DMS camera hardwiring cable (2p)).
Connect the power cable to the DC in terminal of the front and DMS
cameras. BlackVue will power up and start recording. Video files are stored
on the microSD card.
Note
yWhen you run the dashcam for the first time the firmware is automatically loaded
onto the microSD card. After the firmware has been loaded onto the microSD card
you can customize settings using BlackVue Viewer on a computer.
yTo record in parking mode while the engine is off, connect the Hardwiring
Power Cable (included in the box) or install a Power Magic Battery Pack (sold
separately). A Hardwiring Power cable uses the automotive battery to power
your dashcam when the engine is off. A low voltage power cut-off function and a
parking mode timer to protect the automotive battery from discharge is installed
in the device. Settings can be changed in the BlackVue App or Viewer.
ENGLISH ENGLISH

12 BLACKVUE
DMS Calibration
Why do we need calibration?
To utilize AI-based DMS features, calibration process must be preceded to enable DMS.
The calibration process is intended to improve the accuracy of driver recognition since
driver's physical condition (height and eye size), driving position vary from person to
person.
Complete installation DMS camera and Front camera
Turn on the engine, DMS booting up
Adjust the camera angle if necessary to ensure the driver's head is within the
camera. (Please check your face through "Live view" via Wi-Fi direct or BlackVue
Cloud.)
When DMS calibration starts, Blue LED blinks for 30 secs to 2 mins.
When DMS calibration is completed, Green LED turns on.
When DMS is enabled, the device can recognize Driver’s behavior (Drowsy,
Distracted, Hand Distraction, Mask)
Windshield Installation Dashboard Installation
Note
yDuring calibration process, the DMS camera is being recorded.
yEvery time DMS camera starts, calibration operates. and it can recalibrate
automatically while driving.

DMC200 13
Driver Monitoring System Features
Functions Descriptions Indicator LED Beep Alert
Power On When power is turned on, the DMS
booting up. (Blinking) X
Detected
Detects the face within the range of
15degree to top, bottom, left and
right based on the center of the lens.
X
Undetected
When driver is out of detection range
for 60 seconds, it will be detected as
No driver.
O
Drowsy
When driver’s eyes close for more
than 1second or yawning for
2seconds, it will be detected as
drowsy.
O
Distracted
When driver turns head to one side
(left or right) more than about 50
degrees for 5 seconds, or put his
head down to send a text message
using phone for 5 seconds, it will be
detected as distracted.
O
Hand
Distraction
When there is hand movement
around your face for 20 seconds it
will be detected as hand distraction.
(calling, smoking or eating may be
suspected)
O
Mask When driver take off mask, DMS alert
driver to put on mask (Blinking) O
Power Off When power is turned off, the DMS is
turned off. X X
Note
yAmong the functions, Distracted and Hand Distraction are not available if GPS
is under 5km.
yAlgorithm may change in order to improve accuracy.
ENGLISH ENGLISH

14 BLACKVUE
Product specications:
Model Name DMC200
Color/Size/Weight Black/width 115.0 mm x Height 37.88 mm
Camera STARVIS™ CMOS Sensor (Approx.2.1megapixels)
Viewing Angle Diagonal 115°, Horizontal 95°, Vertical 49°
Resolution/
FrameRate
Full HD (1920x1080) @30fps
* Frame rate may vary during Wi-Fi streaming.
Wi-Fi Built-in (802.11 b.g.n)
Speaker
(VoiceGuidance) Built-in
LED Indicators Detection LED (Green/Red/Blue)
Wavelength of
Interlor camera IR
light
940nm (4 Infrared LEDs)
Button Touch key:
Press once to turn on/off beep alerts
Input Power DC 12V –24V (DC Plug: (Ø3.5 x Ø1.35), MAX 1A/12V)

DMC200 15
Power
Consumption
• DR900X-2CH DMS Plus
Normal Mode (WiFi On/GPS On): Avg. 700mA/12V
Normal Mode (WiFi Off/GPS On): Avg. 660mA/12V
Parking Mode (WiFi On/GPS Off): Avg. 650mA/12V
Parking Mode (WiFi Off/GPS Off): Avg. 620mA/12V
• DR750X-2CH DMS Plus
Normal Mode (WiFi On/GPS On): Avg. 650mA/12V
Normal Mode (WiFi Off/GPS On): Avg. 620mA/12V
Parking Mode (WiFi On/GPS Off): Avg. 600mA/12V
Parking Mode (WiFi Off/GPS Off): Avg. 580mA/12V
• DR750X-2CH DMS LTE Plus
Normal Mode (WiFi On/GPS On): Avg. 680mA/12V
Normal Mode (WiFi Off/GPS On): Avg. 640mA/12V
Parking Mode (WiFi On/GPS Off): Avg. 600mA/12V
Parking Mode (WiFi Off/GPS Off): Avg. 560mA/12V
Operation
Temperature
• DR900X-2CH DMS Plus
-20°C–70°C
• DR750X-2CH DMS Plus
-20°C–75°C
• DR750X-2CH DMS LTE Plus
-20°C–75°C
Storage
Temperature
• DR900X-2CH DMS Plus
-20°C–75°C
• DR750X-2CH DMS Plus
-20°C–80°C
• DR750X-2CH DMS LTE Plus
-20°C–80°C
ENGLISH ENGLISH

16 BLACKVUE
High Temperature
Cut-Off
• DR900X-2CH DMS Plus
Approx. 70°C
• DR750X-2CH DMS Plus
Approx. 75°C
• DR750X-2CH DMS LTE Plus
Approx. 75°C
Certifications FCC, CE, Telec, IC, UKCA, RoHS, WEEE
Software BlackVue Viewer
* Windows 7 or higher and Mac Yosemite OS X (10.10) or higher
Application BlackVue Application (Android 5.0 or higher, iOS 9.0 or higher)
Other Features Adaptive Format Free File Management System
* STARVIS is a trademark of Sony Corporation.
For more information about using the DMC200 please download the DMC200 manual
from www.blackvue.com > Support > Downloads.

FCC/IC Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Son fonctionnement est soumis aux deux conditions suivantes:(1) Cet appareil ne doit
pas provoquer d'interferences.(2) Cet appareil doit accepter toute interference, y compris
les interferences qui peuvent provoquer un fonctionnement indesirable de l'appareil.
This equipment should be installed and operated with minimum 20 cm between the
radiator and your body.
Cet appareil doit etre installe et utilise avec un minimum de 20 cm entre le radiateur et
votre corps.
->수정할 예정입니다.
This device should be installed and operated with minimum 20 cm between
the radiator and your body.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
17 BLACKVUE

Cet appareil contient des emetteurs / recepteurs exempts de licence qui sont
conformes aux RSS exempts de licence d'Innovation, Sciences et
Developpement economique Canada.
Son fonctionnement est soumis aux deux conditions suivantes:(1) Cet
appareil ne doit pas provoquer d'interferences.(2) Cet appareil doit accepter
toute interference, y compris les interferences qui peuvent provoquer un
fonctionnement indesirable de l'appareil.
This equipment should be installed and operated with minimum 20 cm
between the radiator and your body.
Cet appareil doit etre installe et utilise avec un minimum de 20 cm
entre le radiateur et votre corps.
18 BLACKVUE
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.

Notes

Notes