BlackVue DR750X-2CH User manual

DR750X-2CH
©2020
DR750X-2CH
instagram.com/BlackVueofficial
ABN Tower 4F, 331, Pangyo-ro, Bundang-gu, Seongnam-si,
Gyeonggi-do, Republic of Korea, 13499
Headquarter
FCC ID: YCK-DR750X-2CH / HVIN : DR750X-2CH
ENGLISH/NEDERLANDS
DR590X-1CH
DR590W-2CH

BLACKVUE
DR590X-1CH
For manuals, customer support and FAQs go to www.blackvue.com
Voor handleidingen, Customer Support en Veelgestelde Vragen, ga naar
www.blackvue.com

Important safety information
For user safety and to avoid property damage, read through this manual and follow
these safety instructions to use the product correctly.
yDo not disassemble, repair, or modify the product yourself.
Doing so may cause re, electric shock, or malfunction. For internal inspection and
repair, contact the service center.
yDo not adjust the product while driving.
Doing so may cause an accident. Stop or park your car in a safe place before
installing and setting up the product.
yDo not operate the product with wet hands.
Doing so may cause electric shock.
yIf any foreign matter gets inside the product, detach the power cord immediately.
Contact the service center for repair.
yDo not cover the product with any material.
Doing so may cause external deformation of the product or re. Use the product
and peripherals in a well-ventilated location.
yIf the product is used outside the optimal temperature range (-20°C – 70°C / -40°F – 158°F),
performance can decline or malfunctions may occur.
yWhen entering or exiting a tunnel, when directly facing into bright sunlight, or when
recording at night without lighting the quality of recorded video may deteriorate.
yIf the product is damaged or the power supply is cut due to an accident, video may
not be recorded.
yDo not remove the microSD card while the microSD card is saving or reading data.
yThe data can be damaged or malfunctions may occur.
3

FCC Compliance Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protections against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception
which can be determined by turning the equipment o and on, the user is encouraged
to ty to correct the interference by one or more of the following measures.
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
yConsult the dealer or an experienced radio, TV technician for help.
yOnly shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly
approved by the grantee or manufacture could void the user’s authority to operate
such equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation of this device.
FCC ID: YCK-DR590X-2CH
4

CAUTION
Any changed or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
CE WARNING
yChanges and modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
yIt is desirable that it be installed and operated with at least 20cm or more between
the radiator and a person’s body (excluding extremities: hand, wrists, feet, and
ankles).
5
Disposal of your BlackVue dashcam
1. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities. Contact local authorities to learn about disposal and
recycling options available in your area.
2. The correct disposal of your BlackVue dashcam will help prevent
potential negative consequences for the environment and human
health.
3. For more detailed information about disposal of your BlackVue
dashcam, please contact your city oce, waste disposal service or
the shop where you purchased the product.

ICC Compliance
This Class [B] digital apparatus complies with Canadian ICES-003.
This radio transmitter has been approved by Industry Canada to operate with the
antenna types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
- IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicable aux appreils
radio exempts de license.
L’exploitation est autoriséee aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l ’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si
le brouillage est susceptible d’encompromettre le fonctionnement.
IC: 23402-DR590X2CH
6

Declaration of Conformity
Product information
For the following
Product: radio equipment/ dashcam
Type: DR590X-1CH
Declaration and applicable standards
Hereby, TJM Supplies B.V. declares that the type of radio equipment DR590X-1CH
conforms to:
Directive EMC 2014/53/EU and the RoHS directive (2011/65/EU) on the restriction of
the use of certain hazardous substances in electronic equipment by applying EN 50581:
2012 and IEC 62321-3-1: 2013.
The full text of the EU declaration of conformity can be found at the following internet
address:
https://blackvue-nederland.nl/declaration-of-conformity/
Importer
Company: TJM Supplies B.V.
Address: Zompstraat 8
8102 HX Raalte
The Netherlands
Email: [email protected]
Phone number: [phone]
Business license number: 72016981
VAT number: NL858946439B01
7

Verklaring van overeenstemming
Productgegevens
Voor het volgende
Product: radioapparatuur/ dashcam
Model(len): DR590X-1CH
Verklaring en toepasselijke normen
Hierbij verklaart TJM Supplies B.V., dat het type radioapparatuur DR590X-1CH conform is
met:
Richtlijn EMC 2014/53/EU en de RoHS richtlijn (2011/65/EU) betreffende beperking
van het gebruik van bepaalde gevaarlijke stoffen in elektronische apparatuur door
toepassing van EN 50581:2012 en IEC 62321-3-1:2013.
De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het
volgende internetadres:
https://blackvue-nederland.nl/declaration-of-conformity/
Importeur
Bedrijfsnaam: TJM Supplies B.V.
Adres: Zompstraat 8
8102 HX Raalte
Nederland
Email: [email protected]
Telefoon: [phone]
KVK nummer: 72016981
BTW nummer: NL858946439B01
8

9
In the box
Check the box for each of the following items before installing the BlackVue dashcam.
Front camera Cigarette lighter
power cable
Quick start guide Cable clips (3 EA)
microSD Card microSD card adapter
Double-sided tape
for the Mounting
Brackets
Hardwiring
power cable
(Optional)
External GPS - USB
Type
(Optional)
Need help?
Download the manual (including FAQs) and the latest rmware from
www.blackvue.com
Or contact a Customer Support expert at [e-mail]
ENGLISH

10
At a glance
The following diagrams explain each part of the BlackVue dashcam.
Front camera
34 mm
Camera lens
Mounting bracket Front security LED
: Lights on during (i) normal mode, (ii) an event is
being recorded (impact detected), (iii) manual
recording has started, or (iv) motion is detected
in parking mode.
: Blinks slowly during parking mode motion
detection standby.
Lock button
42.6 mm
111.8 mm
GPS LED
GPS is on.
Recording LED
: Lights orange in normal mode.
: Lights red when (i) an event is being recorded (impact detected),
or (ii) manual recording has started.
: Lights green in parking mode when motion is detected.
Speaker
LTE/Wi-Fi LED
Lights yellow when Cloud is connected
Lights white when Wi-Fi is connected
Blinks quickly when LTE/Wi-Fi is turning o.

11
Connectivity details label:
- Default Wi-Fi SSID
- Default Wi-Fi password
- Cloud code
- QR code
Serial number label
DC in (Power connector)
GPS connection port or
External connectivity module port
Cover
microSD card slot
Wi-Fi Button
- Press once to turn on/o Wi-Fi.
ENGLISH

12
STEP 1 Install and power up
Install the front camera behind the rear view mirror. Remove any foreign matter and
clean and dry the windshield before installation.
Warning
yDo not install the product in a location where it can obstruct the driver's eld
of vision.
Turn o the engine. Open the cover of the microSD card slot, gently push the card
into the slot until it locks into place and close the cover.
Peel o the protective lm from the double-sided tape and attach the front
camera to the windshield behind the rear-view mirror.

13
Adjust the angle of the lens by rotating the body of the front camera.
We recommend pointing the lens slightly downwards (≈10° below horizontal), so
as to record video with a 6:4 road to background ratio.
GPS receiver or connectivity module (Optional):
Plug in the GPS receiver or connectivity module and attach it in a corner of the
windshield. Use the pry tool to tuck in the cable.
Plug the cigarette lighter power cable into the cigarette lighter socket and the
front camera. Skip to for Hardwiring Power Cable setup.
Use the pry tool to lift the edges of the windshield trim/molding and tuck in the
power cord.
Power cord
ENGLISH

14
Turn on the engine. The BlackVue dashcam will power up and start recording.
Video les are stored on the microSD card.
Turn o the engine. The dashcam will automatically stop recording and power
down. To record in parking mode while the engine is o please connect the
Hardwiring Power Cable (Optional) or install a Power Magic Battery Pack (sold
separately). A Hardwiring Power Cable (Optional) uses the automotive battery to
power your dashcam when the engine is o. A low voltage power cut-o function
and a parking mode timer to protect the automotive battery from discharge is
installed in the device. Settings can be changed in the BlackVue App or Viewer.
Locate the fuse box to connect the hardwiring power cable.
Note
yLocation of the fuse box dier by manufacturer or model. For details, refer to
the vehicle owner's manual.
-After removing fuse panel cover, nd a fuse that powers on when engine is
turned on(ex.cigarette lighter socket, audio, etc) and another fuse that
remains powered on after the engine is turned o (ex.hazard light, interior
light). Connect the ACC+ cable to a fuse that powers on after engine start,
and BATT+ cable to a fuse that remains powered on after engine is turned o.
Note
yTo use battery saver feature, connect the BATT+ cable to the hazard light
fuse. Functions of fuse dier by manufacturer or model. For details refer to
the vehicle owner's manual.

15
-Connect the GND cable to metal ground bolt.
Connect the power cable to the DC in terminal of the front camera. BlackVue
will power up and start recording. Video les are stored on the microSD card.
Note
yWhen you run the dashcam for the rst time the rmware is automatically
loaded onto the microSD card. After the rmware has been loaded onto the
microSD card you can customize settings using BlackVueViewer on a computer.
ENGLISH

16
STEP 2 Playback
Playing video les on your smartphone (Android/iOS)
Search for the BlackVue app in the Google Play Store or Apple App Store and
install it on your smartphone.
“Pair” your smartphone with the BlackVue dashcam via direct Wi-Fi:
(i) Press the Wi-Fi button once to turn on Wi-Fi.
(ii) Go to your smartphone’s Settings then select Wi-Fi, and make sure Wi-Fi is
turned on.
(iii) Choose your BlackVue dashcam from the network list. The dashcam’s default
SSID begins with its model number (e.g. BlackVue590X-******).
(iv) Enter the password and tap join.
* To nd the default Wi-Fi password, unplug the cables and remove the front
camera from its mount. The default Wi-Fi SSID, password and cloud code
are printed on the dashcam's connectivity details label.

17
(v) Open the BlackVue app and select WI-FI.
Select the video le you want to play from the video list.
Note
yDirect Wi-Fi lets you connect your smartphone to your dashcam via Wi-Fi
within a range of 10m.
yAll images shown are for illustration purpose only. Actual App may dier from
images shown.
ENGLISH

18
Playing video les on your computer (Windows/macOS)
Remove the microSD card from the dashcam.
Open side cover To remove
Use the included microSD card adapter to connect the card to a computer.
Download BlackVue Viewer program from www.blackvue.com > Support >
Downloads and install it on your computer.
Run BlackVue Viewer. To play, select a video and click on the play button or double
click the selected video.

19
Windows/macOS Viewer
Note
yAll images shown are for illustration purpose only. Actual program may dier
from images shown.
ENGLISH

20
STEP 3 Changing dashcam's time zone, Wi-Fi password and
other settings.
The dashcam's time zone is initially set to (GMT-11). To display the correct time please
select your time zone.
Using your smartphone (Android/iOS)
“Pair” your smartphone with the BlackVue dashcam via direct Wi-Fi (for details see
STEP 2 ‘Playing video les on your smartphone’).
Open the BlackVue app and select WI-FI.
Tap the button to access the Firmware settings menu.
(i) Select Firmware settings > Basic > Time.
(ii) If you run the dashcam with the GPS receiver or CM100GLTE-M connected,
select your time zone to auto-sync with GPS time. If you do not connect the
GPS receiver or CM100GLTE-M you can set the time and date manually after
enabling Manual time setting.