Blaupunkt ACD 9430 User manual

ACD 9430 3 D92 162 036
76 42 757 013
ACD 9430
Operating Instructions

2 863 4 51
10
97
3
ACD 9430 3 D92 162 036
76 42 757 013
2 Radio 3 CD
1
j
i
9
b c
9
da
g
f
e
h
QuickOut a
b
QuickOut

ACD 9430
12
Front Panel Description
1ON/OFF
Switch on the set by turning knob 1.
2AUD button (sound control/broader
interior sound impression)
BAS – Adjustment of the low frequen-
cies via buttons </> 7.
TRE – Adjustment of the high frequen-
cies via buttons </> 7.
BAL – Adjustment of the left/right volu-
me via buttons </> 7.
FAD – Adjustment of the front/rear vo-
lume via buttons </> 7.
3FM•T button (Frequency Modulation)
FM button
This button is used for shifting between
the different individual FM storage le-
vels and T (Travelstore).
4ARI button
Use this button to activate the ARI func-
tion.
5MIX•lo•m button
CD:
Use this button to play the CD titles in
an arbitrary order.
Radio:
Button to shift between the normal and
high-sensitivity manual station seek
mode, and mono switch.
6• SRC button (Source)
To shift between the individual audio
sources, e.g. CD ♦Radio ♦CD.
By pressing the • SRC button 6for
more than than 3 seconds, the CD is
ejected.
7<>rocker switch
Radio:
Automatic station selection
CD:
Skipping to next/previous title
Pressing the rocker switch < > longer
than 1 sec. activates fast forward (cue)
or fast reverse (review).
8CD slot
Insert the CD with the label side sho-
wing to the top.
9Display
:Preset buttons
Storing a station:
Keep button depressed during radio
operation until the station becomes
audible again.
Recalling a station:
Press button briefly.

13
ACD 9430
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Contents
Front Panel Description............... 12
Important information.................. 13
What you need to know! ....................... 13
Traffic safety ......................................... 13
QuickOut ............................................... 13
Installation/connection .......................... 14
Anti-theft coding .......................... 14
Wrong code number entered ................ 14
Switching the code system on .............. 14
Restart following interruption of power
supply.................................................... 15
Switching the code system off .............. 15
Amplifier Section.......................... 15
ON/OFF ................................................ 15
Bass and Treble Control ....................... 15
Balance and Fader Control ................... 16
Radio Section ............................... 16
Selecting a Station ................................ 16
Tuning in a Station Automatically.......... 16
Manual Tuning ...................................... 16
Adjusting the Station Seek Sensitivity... 16
Mono/Stereo Operation......................... 16
Memorizing a Station ............................ 17
Automatically Storing the Strongest
Stations ................................................. 17
Activating a Stored Station.................... 17
Traffic Messages (ARI) ......................... 17
Switching Traffic Messages On and Off 17
Acoustic Alarm ...................................... 17
ARI during CD Operation ...................... 17
Automatic Start of the Station Seek
Operation .............................................. 18
CD Section .................................... 18
Inserting the Disc .................................. 18
Ejecting the Disc ................................... 18
Title Selection/Cueing and Reviewing .. 18
Mix Function.......................................... 18
Changing the Audio Source with SRC .. 18
Programming with DSC ............... 19
Appendix....................................... 19
Technical Data ...................................... 19
What To Do If Your Car Stereo Needs
Service? ................................................ 19
Important information
What you need to know!
Beforestarting to use your new car radio you
shouldcarefullyreadthroughtheinformation
on “Traffic safety” and “Anti-theft coding”.
Traffic safety
Traffic safety has always priority. Use your
car radio in such a manner that you are
always able to cope with and react to the
prevailing traffic situation at any given time.
Remember, even at 50 km/h you are still
moving at a speed of 14 m per seconds.
It is also very important that you are able to
hear, and react to, acoustic warning signals
around you, for example from the police or
the firebrigade.
Therefore, adjust the volume reasonably.
QuickOut
Using the QuickOut handle you can easily
pullyourradiooutoftheinstallationcompart-
ment to take it along. The preset stations
remain stored for a longer time.
To take out the radio.
•press knob (a), take the handle (b) and
pull the unit out.

ACD 9430
14
To listen to the radio or cassette again,
•insert the set into the compartment until
it stops and move the handle back to
the front panel.
If the coding system is off, your set will be
ready for operation.
If the coding system is on, proceed as des-
cribed under “Restart following interruption
of power supply”.
Installation/connection
The code system can only be switched on
and off, if the radio is connected to perma-
nent power.
If you like to install your new car radio by
yourself or add other audio components to
the existing ones, then please read carefully
the enclosed instructions on installation and
connection.
Do not connect the loudspeaker outputs to
ground!
Only use the accessory and replacement
parts approved by Blaupunkt.
Anti-theft coding
The car radio comes standard with the code
system deactivated.
If the anti-theft coding system is on while the
power supply to the unit is interrupted (e.g.
theft,disconnectingthecarbattery),thesetis
electronically blocked. Then it may only be
used again after the appropriate code num-
ber has been entered (see car radio pass-
port).
Wrong code number entered
Itshouldnotbe possible forthievestoascer-
tain the code number by trial-and-error. This
is why the set will be blocked for a certain
period of time, if an incorrect code number is
entered. In this case, “- - -” will appear in the
display.
This waiting time is 10 seconds after the first
three attempts, and 1 hour following subse-
quent attempts.
After 19 unsuccessful attempts, “OFF” will
appear in the display and the set can no
longer be restarted.
Note:
Keep you car radio passport with the code
number in a safe place in order to avoid
“unauthorized access” to your car radio.
If the power supply to the radio is interrupted
while the code system is switched on, you
need to know the right code number.
The radio will operate again as soon as you
have entered the right code number.
If you lose your radio passport and have
forgotten your code number, you will not be
able to restart the set after the power supply
hasbeeninterrupted.Inthiscase, your radio
can only be reset in our central customer
service workshop or in one of our service
agencies abroad.
Switching the code system on
Precondition:
The radio must be connected to permanent
power.
In order to switch the code system on:
•Turn the radio off.
• Hold down the preset buttons 1and 4
simultaneously.
•Turn the radio on.
“Cod” briefly appears before the radio
begins to operate.
•Release preset buttons 1and 4.
The code system is on.
“Cod” will be briefly displayed each time the
radio is turned on.

15
ACD 9430
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Restart following interruption of
power supply
(Code system switched on)
•Switch on the set.
“Cod” will appear in the display.
•Briefly press preset button 1, “000” will
appear in the display.
•Enter the code number given in the
Blaupunkt car radio passport:
Preset button 1 only allows to choose
“0” or “1”. The first “0” will not be dis-
played.
Example: the code number is 0521.
-Press preset button 1until “000” ap-
pears in the display.
-Press preset button 2five times,
“500” appears in the display.
-Press preset button 3twice, “520”
appears in the display.
-Press preset button 4once, “521”
appears in the display.
•To confirm the code number:
Press the upper part of the rocker
switch .
Your car radio is now ready for operation.
If three dashes appear again in the display,
you have entered a wrong code number.
Now it is essential to enter the correct code
after the waiting period has elapsed (Cod in
the display).
If the radio is turned off before the waiting
period has elapsed, then the waiting period
restarts as soon as the radio is turned on
again.
Switching the code system off
•Turn off the radio.
•Simultaneously press preset buttons 1
and 4and hold them down.
•Turn the set on.
“Cod” will appear in the display.
•Enter the code number given in the
Blaupunkt car radio passport and con-
firm: See example “Restart following
interruption …”.
The code system is now deactivated.
Amplifier Section
ON/OFF
To switch on the set:
•Turn button 1clockwise.
To switch off the set:
•Turn button 1counterclockwise.
Bass and Treble Control
Bass Control
To adjust the low frequencies:
•Press the AUD button 2.
Display 9gives you bas plus a num-
ber between -7 and +7.
•Press rocker switch </> 7on the right
to boost the bass frequencies or on the
left for bass reduction. The number on
the display 9changes between -7 and
+7.
Treble Control
To adjust the high frequencies:
•Press the AUD button 2until tre and a
number between -7 and +7 appears on
the display.
•Press rocker switch </> 7on the right
to boost the high frequencies or on the
left for treble reduction. The number on
display 9changes between -7 and +7.

ACD 9430
16
Balance and Fader Control
Balance control
To balance the sound level left/right:
•Press the AUD button 2until bal is
shown on the display.
Press rocker switch </> 7on the left
or right to adjust the sound impression
according to your personal preferences.
Display 9gives you a number bet-
ween -9 and +9.
Fader control
To balance the front/rear sound level:
• Press the AUD button 2until fad is
shown on the display.
Press rocker switch </> 7on the left
or right to adjust the sound impression
according to your personal preferences.
Display 9gives you a number bet-
ween -9 and +9.
Note:
Ifthe rocker switch < > is kept depressed (on
the left or right), the set quickly advances to
the final values (+7/+9 or -7/-9) or to the “0”
position.
Radio Section
Selecting a Station
With your car radio you can select stations
from the FM (ultra-short wave) and FM-Tra-
velstore level.
To select FM,
•press the FM•T button 3briefly. “FM”
lights up on display 9a.
To select FM-Travelstore,
•press the FM•T button 3briefly until
“FM•T” is shown on display 9b.
For more information on this function
see chapter “Automatically Storing the
Strongest Stations”.
Tuning in a Station Automatical-
ly
Tuning in the following station
•Press the </> rocker switch 7on the
right. The car stereo automatically
starts searching for the next station.
Tuning in the previous station
•Press the </> rocker switch 7on the
left. The car stereo automatically starts
searching for the previous station.
If the </> rocker switch 7is kept de-
pressed on the right or the left, the sta-
tion seek operation continues to be
carried out quickly in the corresponding
direction.
Manual Tuning
To manually tune in a station,
•press the lo•m button 5until “m” lights
up on display 9f.
Youcannowmanuallysearchforthedesired
stations via the </> buttons 7.
Adjusting the Station Seek
Sensitivity
With this set you can modify the automatic
station seek sensitivity in all wavebands.
If you want to search for strong stations only
(reduced sensitivity):
•Press the lo button 5until “lo” lights
up on display 9e.
Ifyoualsowanttosearchforweakerstations
(increased sensitivity):
•Press the lo button 5once again; the
“lo” indication on display 9e goes out.
Mono/Stereo Operation
If the lo•m button 5is pressed longer than
2secs. but less than 8 secs., the set swit-
chesoverto mono andthestereo symbol (h)
goes off.
If the lo•m button 5is pressed longer than

17
ACD 9430
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
2secs. but less than 8 secs., the set swit-
chesovertostereoandthestereo-symbol(h)
lights up in the display.
Whenthecarradioisswitchedonitisalways
in stereo mode.
Memorizing a Station
YoucanmemorizetwoFMstationswitheach
of the preset buttons :. Display 9a, b
either indicates the FM storage level (“FM”)
or the Travelstore level (“T”).
To memorize a station:
Tuneinthedesiredbroadcaster(seechapter
Tuning in a Station Automatically/Manual
Tuning) first. Now press one of the preset
buttons :until the radio resumes play (ap-
prox. 2 seconds). The station is now stored.
Note:
IfyoutunetoanFMstationalreadystoredon
the storing levels FM or Travelstore, the
coresponding storing level and the preset
button will flash in the display.
Automatically Storing the Stron-
gest Stations
(Travelstore)
WithTravelstore,youhavetheopportunityto
automatically store the 5 strongest FM stati-
ons of your respective area and have them
sortedaccordingtotheirsignalstrength.The
strongest station is then stored on preset
button 1, the second strongest on preset
button 2, etc. This feature is of special use
while travelling.
•Press the FM•T button 3for at least
two seconds.
The set searches for the strongest FM
stations and memorizes them on the
“T” storage level (Travelstore). Once
the process is finished, the car radio
automatically tunes in to the strongest
station.
If required, it is also possible to manually
storeastationontheTravelstorelevel.Ifless
than 5 stations can be received, the free
buttons are briefly represented by dashes.
Activating a Stored Station
If required, the memorized stations can be
activated at a keystroke.
•For this, choose the FM or T storage
level and briefly
•press the respective preset button :.
Traffic Messages (ARI)
Many FM stations broadcast local traffic
messages at regular intervals. These sta-
tions can easily be detected with the ARI
system. A traffic station is identified by the
“SK” indication on display 9g (“SK” stands
for the German equivalent for “station identi-
fication”).
Switching Traffic Messages On and Off
The ARI function is switched on by pressing
theARIbutton4.Display9cwillthengive
you the “ARI” indication. When listening to a
station without the ARI identification, an au-
diblealarmtonewillbeproducedafterappro-
ximately 3 seconds.
Acoustic Alarm
Whenleavingthecoverageareaofthetuned
instation, your car radio automatically sends
outanacoustic alarm afterapproximately 30
seconds. This alarm tone is also produced
when pressing a preset button with a non-
ARI station allocated to it.
ARI during CD Operation
Thisset offers you the opportunity to listen to
a compact disk and at the same time be
prepared for incoming traffic messages.
Whensuchamessagecomesin,theCDtitle
will be muted until the message is over.
To select this ARI preference during CD
reproduction,
•shift to the radio mode using the SRC
button 6.

ACD 9430
18
•Now press the ARI button 4. The ARI
indication lights up on display 9c.
•Then tune in to one of the traffic stati-
ons of your area.
Switch over to CD operation by either
• inserting a disk, or - if a CD is already
inserted by
•pressing the SRC button 6.
CD reproduction will be interrupted as soon
as a traffic message is “put through”.
Whenleavingthecoverageareaofthetuned
in traffic station, your car stereo will automa-
tically start searching for a new one.
If no ARI station is found after having scan-
ned the frequency band several times, the
system sends out an alarm tone.
In this case switch off the ARI function by
•pressing button 4. The alarm tone
stops.
Automatic Start of the Station Seek
Operation (CD play)
Your set will also automatically start seeking
for a new traffic station when leaving the
coverageareaofthetunedintrafficprogram-
me while listening to a disk. An alarm tone is
sent out during the search operation.
CD Section
Inserting the Disk
With this set you can play the normal stan-
dard CDs without having to use an adapter:
•Switch the set on.
•Insert the CD (label side up) without
applying force.
Thediskisautomaticallypulledintotheunit
to reach the playing position. Once it has
been fed in, reproduction starts.
Ejecting the Disk
• To eject the disk, keep the • SRC
button 6depressed at least 2 sec.
NeverblockorsupporttheCDmechanismin
any way, since this would damage the set.
Title Selection/Cueing and Re-
viewing
After the CD has been inserted into the set,
„Cd“ lights up on display 9. The display
indication9ichangesto“T1”(Track1)after
approx. 5 seconds. You can skip or repeat
titles by using the </> buttons 7.
Cue (Fast forward):
• Keep depressed the right side of the
rocker switch </> 7for more than than
2 second.
Review (Fast backward):
• Keep depressed the left side of the
rocker switch </> 7for more than
than 1 second.
Mix Function
Press the Mix button 5to listen to the titles
in an arbitrary order.
WhenMix ison, the “Mix” indication lights up
on display 9j.
Changing the Audio Source with
SRC
You can shift between the connected audio
sources in the order CD ♦Radio ♦CD. To
switch over to another audio source during
CD operation,
•press the SRC button 6.
The set changes to radio operation.

19
ACD 9430
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Programming with DSC
The car radio’s DSC function (Direct Soft-
ware Control) allows you to adjust the seek
tuning sensitivity for FM and the volume of
ARI traffic messages.
Adjusting the seek tuning sensitivity:
•Press the lo•m 5button longer than
8secs. The display gives you “lo” and a
number between 1 and 3.
•Adjust the sensitivity using the rocker
switch < > 7.
1
=
^
high sensitivity
3
=
^
normal sensitivity
To store the adjustment,
•press th lo•m button once again.
For setting the volume of ARI traffic messa-
ges,
•press the ARI button 4longer than
8secs. The display indicates “L” and a
number between 1 and 9.
•Use the rocker switch < > 7to adjust
the volume of traffic messages
1
=
^
low volume
9
=
^
high volume
To store the adjustment,
•press the ARI button once again.
Appendix
Technical Data
Amplifier:
Output power: 4 x 8 watts acc. to DIN
45324/3.1
FM:
Frequency
response: 50 - 16 000 Hz (-3dB)
CD:
Frequency
response: 20 - 20 000 Hz (-3 dB)
Preamp-Out: Output impedance
150 Ω
What to Do If Your Car Stereo
Needs Service?
Whenever your car radio fails to operate
properly and therefore requiring repair by an
authorized service centre, please do not for-
get to take the car radio passport along with
you.
Modifications reserved!