Enable dual key Fire Alarm function
Enable dual key MedicalAlarm function
Disable all dual key functions
Change Keypad PIN Code:
1. Enter old code + “Status” Key
2. Enter new 4-digit code + “#” key
Enable Arming without Use PIN code
function
Enable Arm with User PIN code function
(Default)
Enable Arming with KP PIN code
function
R
RF
FI
ID
D
T
TA
AG
G
M
Ma
an
na
ag
ge
em
me
en
nt
t
The Keypad can function with the RFID tags included in the
package. By assigning User PIN Code to a Tag, you can use the
Tag to Arm/Home/Disarm the Control Panel with a simple swipe.
Up to 6 tags can be stored in the Keypad and assigned to User
PIN Codes for panel control:
Add New Tag:
1. Enter Keypad Test Mode.
2. Enter “＊”+“1”for Tag Management. Red Status LED will light up.
3. Enter a 4-digit “Control Panel User PIN Code”+ “#”key.
Status Blue LED
flashes with 4 beeps
Error: Wrong PIN Code length
Status Red LED
flashes with 4 beep
Error: Keypad already stored 6 Tags
4. Put the TAG close to the Keypad when Status Red LED is
flashing.
Status RED LED On
with 2 beeps
Status Red LED On
with 1 bee
Same PIN Code already assigned to
this Tag
Status Red LED On
with 4 beeps
Error: Tag already assigned to another
User PIN Code
5. After finish adding new Tag, press “Disarm”key to exit Tag
Management.
Remove Existing Tag:
1. Enter Keypad Test Mode.
2. Enter “＊”+“1”for Tag Management. Red Status LED will light
up.
3. Enter the User PIN Code of the Tag you want to remove, then
press the Status key.
4. The Keypad will emit a long beep, the Tag info is removed.
A
Ar
rm
m/
/H
Ho
om
me
e/
/D
Di
is
sa
ar
rm
m
If Remote Keypad is set to “Arm with Use PIN code”(“＊” + “9”
under Test Mode)
1. Enter a Control Panel User PIN Code +
“Arm”Key.
2. Press “Arm”Key + put Tag on Keypad.
1. Enter a Control Panel User PIN Code +
“Home”Key.
2. Press “Home”Key + put Tag on Keypad.
1. Enter a Control Panel User PIN Code +
“Disarm”Key.
2. Press “Disarm”Key + put Tag on Keypad.
If Remote Keypad is set to “Arm without Use PIN code”(“＊” + “8”
under Test Mode)
Enter a Control Panel User PIN Code +
If Remote Keypad is set to “Arm with Keypad PIN code”(“＊” +
“0”under Test Mode)
Enter Keypad PIN Code + “Arm”Key
Enter Keypad PIN Code + “Home”Key
Enter Keypad PIN Code + “Disarm”Key
C
Ch
he
ec
ck
ki
in
ng
g
C
Co
on
nt
tr
ro
ol
l
P
Pa
an
ne
el
l
S
St
ta
at
tu
us
s
Press the Status key to inquire Control Panel status, the Status
LED will light up according to Control Panel mode
D
Du
ua
al
l
K
Ke
ey
y
A
Al
la
ar
rm
m
F
Fu
un
nc
ct
ti
io
on
n
Dual Key Alarm function will activate alarm when both keys are
pressed at the same time. To use the functions, please enable
them under Test Mode. (Default are disabled)
L
LE
ED
D
I
In
nd
di
ic
ca
at
to
or
rs
s
A
Ac
ct
ti
iv
ve
e
L
LE
ED
D
The Active LED light up whenever any key is pressed.
Keypad in Normal Operation
Keypad in Normal Operation and under
Low Battery
Keypad in Test Mode and under Low
Battery
The Status LED light up during operation or when the “Status”key
is pressed to inquire Control Panel status
No reply from Control Panel
Incorrect PIN code
Request for Home arm when under Away
arm mode
Request for Force Arm
The Fault LED light up whenever faults are detected in the alarm
system.
The Remote Keypad uses one 3V lithium battery as its power
source. It also features low battery detection function to notify the
Control Panel when battery voltage is low.
When the Remote Keypad is on low battery, follow the procedure
below to change the batteries.
1. Open the back cover
2. Remove the old batteries
3. Press any key several times to fully discharge.
4. Insert the new batteries observing correct polarity.
5. Replace the back cover.
F
Fa
ac
ct
to
or
ry
y
R
Re
es
se
et
t
If you forget your Keypad PIN code, or the Remote Keypad has
any problem, you can reset the Remote Keypad to factory
default.
1. Open the back cover and remove the battery
2. Press and hold “3”key and insert battery
