Blaupunkt KP-S3 User manual

Wireless Remote Keypad (KP-S3)
P
Pa ar rt ts s D De es sc cr ri ip pt ti io on n
1. Active LED (Green)
2. Transmission LED (Red)
3. Fault LED (Orange)
4. Away Arm Key
5. Home Arm Key
6. Key
7. Disarm Key
8. Mounting Hole Cover
9. Panic Alarm
Press both 1 and 3 key to trigger Panic alarm
10. Fire Alarm
Press both 4 and 6 key to trigger Fire alarm
11. Emergency Alarm
Press both 7 and 9 key to trigger Emergency alarm
12. Mounting Holes
13. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening or removal from mounted surface.
14. Battery Insulator
P
Pa ac ck ka ag ge e C Co on nt te en nt t
1 x Remote Keypad
2 x wall plugs and screws
1 x CR2450 3V lithium battery (pre-installed)
For learning the Remote Keypad:
1. Pull out the battery insulator to activate battery.
2. Put the Control Panel into learning mode.
3. Press both # and keys to transmit learn code
4. Refer to Control Manual to complete the learning process.
The Remote Keypad has 2 mounting holes which are covered
from the front for wall mounting.
1. Lift the mounting hole cover to reveal the 2 mounting holes.
2. Use the two mounting holes to mark position on the wall at
chest height.
3. Drill holes into the wall in marked location.
4. Fix the keypad onto the wall with the screw and plugs
provided.
5. Replace the mounting hole covers.
S
St ta an nd db by y M Mo od de e
The Remote Keypad features a power saving feature. When no
key is pressed for 5 seconds, the Remote Keypad will turn off
automatically to conserve power. When any key is pressed, the
Remote Keypad will wake up and turn on Active LED to indicate it
is now under normal operation
K
Ke ey yp pa ad d S Se et tt ti in ng g
The Remote Keypad features a Test (programming) mode for you
to customize its setting. Before you start using the Remote
Keypad, you should first finish configuration setting.
The Remote Keypad also feature a Keypad PIN code which is
used to access the Test mode, To enter Test Mode, Enter
“0000”(Default Keypad PIN code) + “＊”key, the Active LED will
begin to flash to indicate Keypad is now under Test Mode.
Under Test Mode, the following functions include:
Key
Function
“＊” + “1”
Transmit learn code (same as pressing
both #and keys under normal mode)
“＊” + “2”
Enable dual key Panic Alarm function
“＊” + “3”
Enable dual key Fire Alarm function
“＊” + “4”
Enable dual key MedicalAlarm function
“＊” + “5”
Disable all dual key functions (Default)
L
Le ea ar rn ni in ng g
O
Op pe er ra at ti io on n
I
In ns st ta al ll la at ti io on n
Remove
Remove
Mounting Hole
Mounting Hole

“＊” + “6”
Change Keypad PIN Code:
1. Enter old code + “” Key
2. Enter new 4-digit code + “#” key
“＊” + “8”
Enable Arming without Use PIN code
function
“＊” + “9”
Enable Arm with User PIN code function
(Default)
“Disarm” twice
To leave Test Mode
A
Ar rm m/ /H Ho om me e/ /D Di is sa ar rm m
If Remote Keypad is set to “Arm with Use PIN code”(“＊” + “9”
under Test Mode)
Away Arm
Enter a Control Panel User PIN Code +
“Arm”Key
Home Arm
Enter a Control Panel User PIN Code +
“Home”Key
Disarm
Enter a Control Panel User PIN Code +
“Disarm”Key
If Remote Keypad is set to “Arm without Use PIN code”(“＊” + “8”
under Test Mode)
Away Arm
Press “Arm”Key
Home Arm
Press “Home”Key
Disarm
Enter a Control Panel User PIN Code +
“Disarm”Key
D
Du ua al l K Ke ey y A Al la ar rm m F Fu un nc ct ti io on n
Dual Key Alarm function will activate alarm when both keys are
pressed at the same time. To use the functions, please enable
them under Test Mode. (Default are disabled)
“1”+ “3”
Panic Alarm
“4”+ “6”
Fire Alarm
“7”+ “9”
EmergencyAlarm
L
LE ED D I In nd di ic ca at to or rs s

 A Ac ct ti iv ve e L LE ED D
The Active LED light up whenever any key is pressed.
Off
Keypad in Standby Mode
Green LED On
Keypad in Normal Operation
Green LED Flash
Keypad in Test Mode

 T Tr ra an ns sm mi is ss si io on n L LE ED D
The Transmission LED lights up whenever the Keypad transmits
a radio signal

 F Fa au ul lt t L LE ED D
The Fault LED light up when the Keypad is activated under fault
condition
Orange LED On
Keypad tamper switch is triggered
Orange LED Flash
Keypad is under low battery
B
Ba at tt te er ry y
The Remote Keypad uses one 3V CR2450 lithium battery as its
power source. It also features low battery detection function to
notify the Control Panel when battery voltage is low.
When the Remote Keypad is on low battery, follow the procedure
below to change the battery.
1. Open the back cover.
2. Remove the old battery carefully with a minus screw driver by
inserting the screw into gap in battery compartment, the lift the
battery as picture below.
Do not remove the battery by hand to avoid risk of damaging
the battery compartment.
3. Press any key several times to fully discharge.
4. Insert the new battery observing correct polarity.
5. Replace the back cover.
F
Fa ac ct to or ry y R Re es se et t
If you forget your Keypad PIN code, or the Remote Keypad has
any problem, you can reset the Remote Keypad to factory
default.
1. Open the back cover.
2. Open the back cover and remove the battery.
3. Press and hold “3”key and insert battery.
4. The Remote Keypad will sound 3 short beeps.
5. Release “3”key, the reset process is now complete
E
En nv vi ir ro on nm me en nt ta al l C Co on nd di it ti io on n
-10°C to 40°C, relative humidity 85% non-condensing.
R
Ra ad di io o
868 MHz
S
Sp pe ec ci if fi ic ca at ti io on n