Blaze King TORINO II 1606 User manual

OM-1606 E V1.03 April 2, 2014
TORINO II 1606
FREESTANDING DIRECT VENTED GAS ROOM HEATER
for use with natural gas or LPG
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com
OPERATION & INSTALLATION
MANUAL
WARNING:If the information in these
instructions are not followed exactly, a fire
or explosion may result causing property
damage, personal injury or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
This appliance may be installed in
an aftermarket, permanently located,
manufactured (mobile) home, where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.

OM-1606 E V1.03 April 2, 2014
Page 2 TORINO II Freestanding 1606
Table of Contents
INTRODUCTION _____________________________________________________________ 3
CERTIFICATION LABEL________________________________________________________ 4
GENERAL INFORMATION ______________________________________________________ 5
APPLIANCE DIMENSIONS______________________________________________________ 7
INSTALLATION CLEARANCES __________________________________________________ 8
ASSEMBLY INSTRUCTIONS_____________________________________________________ 9
INSTALLATION INSTRUCTIONS_________________________________________________ 11
RIGID VENTING PARTS LIST____________________________________________________ 20
INTERMITTENT PILOT & VALVE ________________________________________________ 23
WIRING DIAGRAM ___________________________________________________________ 25
LIGHTING INSTRUCTIONS _____________________________________________________ 26
THERMOSTAT REMOTE CONTROL ______________________________________________ 27
MAINTENANCE ______________________________________________________________ 32
SERVICING __________________________________________________________________ 34
FUEL CONVERSION ___________________________________________________________ 35
BURNER TRAY REMOVAL AND INSTALLATION ____________________________________ 37
VALVE REMOVAL AND INSTALLATION___________________________________________ 38
FAN REMOVAL AND INSTALLATION _____________________________________________ 39
ALLOWABLE TERMINATION LOCATIONS _________________________________________ 40
TROUBLESHOOTING__________________________________________________________ 41
REPLACEMENT PARTS ________________________________________________________ 43
WARRANTY _________________________________________________________________ 45
NOTES______________________________________________________________________ 49
Manufactured By
Valley Comfort Systems Inc.
1290 Commercial Way
Penticton, BC V2A 3H5
CANADA
Phone: [phone]
Fax: [phone]
Blaze King Industries
146 A Street
Walla Walla, WA 99362
U.S.A.
Phone: [phone]
Fax: [phone]

OM-1606 E V1.03 April 2, 2014
Page 3
TORINO II Freestanding 1606
INTRODUCTION
To Our Valued Customers
Dear Customer:
ank you for purchasing a Torino II Gas Heater.
e Torino II is one of the most advanced direct vented gas heaters on the market. It is designed
using the latest technology and manufactured to the highest quality.
is owner's manual explains the steps required to safely assemble, install, operate, and maintain
your new heater. Please carefully read these requirements for safe installation and proper
operation before installing and using your heater.
Obtain permits from the Building Inspector or Fire Department, if local laws require. Check local
building and re codes before installing your heater. When you have completed the installation,
have it checked by your local inspector. Disregarding inspection and code requirements may
jeopardize your homeowner's insurance. Since some insurance carriers require notication of a
stove installation, contact your insurance agent. We want your Blaze King to give you a lifetime
of trouble-free operation.
While we have made every eort to make these instructions as complete as possible, some
installation or operating conditions may not be covered. If you have any questions that are not
answered here, contact your Blaze King dealer, Local Building Inspector, Fire Department, or our
customer service department at Blaze King. In the USA please call (509)-522-2730 or in Canada
please call (250)-493-7444.
e Management and Employees of
Blaze King Industries, Inc

OM-1606 E V1.03 April 2, 2014
Page 4 TORINO II Freestanding 1606
MANUFACTURE DATE
JAN FEB MAR APR MAY JUN 
JUL AUG SEP OCT NOV DEC 
2012 2013 2014 2015 2016 2017 
ANSI Z21.88-2009/CSA2.33-2009, “Vented Gas Fireplace Heaters”, CAN/CGA 2.17-M91 “Gas-Fireplaces For UseAt HighAltitudes.”
Test é à ANSI Z21.88-2009/CSA2.33-2009 “Foyer au gaz avec éventet”, CAN/CGA2.17-M91 “Appareils de chauffage au gaz utilisés en hautes altitudes”
Model: Torino II top vent appliance
Modèle: Torino II appareil à évent en haut
Orifice (DMS) 0-1370 m NATURALGAS 36 LP GAS 52
Input rating / Puissance d’entrée (BTU/hr / Kw) 0-1370m 0-4500 ftAlt.
Minimum Input / Entrée Minimum (BTU/hr / Kw)
Manifold Pressure High Setting (In w.c. / kPa)
Manifold Pressure Lo Setting (In w.c. / kPa)
Minimum Inlet Pressure / Pression d’entrée Minimum (In w.c. / kPa)
30,500 / 8.94
20,600 / 6.04
3.5 / 0.87
1.6 / 0.40
7.0 / 1.74
30,500 / 8.94
17,200 / 5.04
11.0 / 2.74
2.9 / .72
11.0 / 2.74
This appliance must be installed in accordance with local codes if any: if not follow ANSI Z223.1 and CAN 1-B149 GasAppliance Installation CodeANSI Z223.1 / NFPA
54 or Natural Gas and Propane Installation Codes CSAB149.1. Cet appareil doit être installé selon les codes locaux, s’il y en a: sinon suivez l’actuel ANSI Z223.1 et
CAN 1-B149Appareil au Gaz CodeANSI Z223.1 / NFPA54 ou Gas Naturel et Propane CSAB149.1.
VENTED GAS FIREPLACE HEATER—NOT FOR USE WITH SOLID FUEL
FOYERAU GAZAVEN ÉVENT—NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE
FOR USE WITH GLASS DOORS CERTIFIED WITH THEAPPLIANCE ONLY. / UTILISER SEULEMENTAVEC DES PORTES VITRÉES CERTIFIÉES POUR CET
APPAREIL.
ALSO FOR USE IN OEM / MOBILE (MANUFACTURED) HOMES AFTER HOME IS ON SITE. Convertible for use with natural gas or propane as follows: For natural gas
when equipped with orifice # 36, for propane when equipped with orifice # 52.
MAY BE INSTALLED IN ABEDROOM OR SITTING ROOM WHEN INSTALLED WITH ALISTED THERMOSTAT CONTROLIN CANADA.
AUSSI POUR L’USAGE DANS LES MAISONS (MANUFACTURÉES) MOBILESAPRÈS QUE LAMAISON SE TROUVE SUR LE CHANTIER. Convertible pour l’usage
avec le gaz naturel ou le propane comme suit: Pour le gaz naturel une fois équipé de l’orifice # 36, pour le propane une fois équipé de l’orifice # 52.
PEUT ÊTRE INSTALLÉ DANS UNE CHAMBRE À COUCHER OU UN SALON UNE FOIS INSTALLÉAVEC UN THERMOSTAT ÉNUMÉRÉAU CANADA.
MINIMUM CLEARANCES TO COMBUSTIBLES / ESPACES MINIMUM REQUIS ENTRE L’APPAREIL ET DES MATÉRIAUX COMBUSTIBLES.
Unit to Sidewall / Unité au mur l’atéral 254 mm (10 in) Unit to Back wall / Unité au mur arriére 152 mm (6 in)
Floor / Plancher Unprotected (in Canada) / Sans protection (Canada)
Floor / Plancher Unprotected (in U.S.A.) / Sans protection (U.S.A.)
Vent pipe / Event (vertical) 25 mm (1 in)
Electrical Rating: 115 Volts, 0.7 Amp, 60 Hz
DANGER: Risk of electrical shock. Disconnect power before servicing unit. Do not route power cord beneath heater.
DANGER: Risque d’électrocution. Débrancher le courant avant de réparer l’unité. Ne pas mettre la corde d’alimentation en dessous de l’appareil de chauffage.
This appliance must be installed in accordance with the Standard CAN/CSAZ240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and
Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/NCSBCSA225.1/NFPA501A, Manufactured Home
Installations Standard. / Cet appareil doit être installe selon les codes CAN/CSAZ240 MH, maisons (manufacturées) mobiles, au Canada, sinon applicable, utilisez ANSI/
NCSBCSA225.1/NFPA501A, Manufactured Home Installations Standard.
Listed Vented Gas Fireplace Heater / Foyer chauffé au gaz avec évent
Torino II Free Standing W/N #16960
This stove is factory equipped for 0-1370 m (0-4500 ft)
Ce foyer est manufacturée et équipé pour 0-1370 m (0-4500 pied)
Certified for U.S. and Canada
Certifiépour le Canada et les Etas - Unis
Serial No. -
MINIMUM ALCOVE CLEARANCES
A Side Wall to unit side 10” (254 mm)
B Back Wall to unit side 6” (152 mm)
C Corner to Side Wall 4 3/8” (111 m)
MinimumAlcove Height 48” (1219 mm)
Manufactured in U.S.A. by: Blaze King Industries
146A Street, Walla Walla, WA
U.S.A. 99362
Manufactured in Canada by: Valley Comfort Systems Inc.
1290 Commercial Way, Penticton, B.C.
Canada V2A3H5
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local
codes. See owners manual for details. This appliance is not convertible for use with other gases unless a certified kit is used. This vented gas fireplace is not for use with air filters.
Cet appareil sert seulement avec le type de gaz indiqué sur la plaque de contrôle et peut être installé dans un marché des accessoires, maison (mobile) de manière permanente placée et
manufacturée où non interdit par des codes locaux. Voir le manuel d’installation pour des détails. Cet appareil n’est pas convertible pour l’usage avec d’autres gaz à moins qu’un kit certifié soit
employé. Ce foyer au gaz à évent ne peut être utilisé avec des filtres à air.

#0375ef1012.indd
CERTIFICATION LABEL

OM-1606 E V1.03 April 2, 2014
Page 5
TORINO II Freestanding 1606
GENERAL INFORMATION
APPLIANCE CERTIFICATION
is appliance is tested and certied to the following US and Canadian gas appliance standards:
• ANSI Z21.88b-2007 / CSA 2.33b-2007 Vented Gas Fireplace Heaters,
• CAN/CGA-2.17-M91 Gas-Fired Appliance for Use at High Altitudes
• CSA P.4.1-02 Testing Method for Measuring Annual Fireplace Eciency
Please contact Valley Comfort or Blaze King, if you have any questions regarding the certication of this
appliance.
• e installation must conform with the local codes or, in the absence of local codes, with the current
National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code, CSA-B149.1, in Canada.
• A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable,
the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped
Recreational Vehicles and Mobile Housing, CSA Z240.4.
• e appliance and its appliance main gas valve must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).
• is gas appliance must not be connected to a chimney ue serving a separate solid-fuel burning appliance.
• e appliance, when installed, must be electrically grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical Code, ANSI/NFPA 70, in the US, or the Canadian
Electrical Code, CSA C22.1, in Canada.
• Do not use this appliance if any part has been under water. Immediately call a qualied service technician to
inspect the appliance and to replace any part of the control system and any gas control which has been under
water.
• Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation aer servicing.

OM-1606 E V1.03 April 2, 2014
Page 6 TORINO II Freestanding 1606
GENERAL INFORMATION cont.
INSTALLATION CODES
is appliance must be installed by a qualied gas appliance installer. is appliance is certied for installation
in a bedroom or a bedsitting room. is appliance is only for use with the type of gas indicated on the rating
plate and may be installed in an aermarket, permanently located, manufactured (mobile) home where not
prohibited by local codes. is appliance is not convertible for use with other gases, unless a certied kit is
used. Only for direct discharge without duct connection. is appliance must be direct vented using listed and
approved Simpson Dura-Vent, Selkirk, Security or American Metal Products vent components.
SPECIFICATIONS
MODEL Torino II Natural Gas (NG) Propane (LPG)
Manifold Pressure 3.5 in. w.c. (0.87kPa) 11.0 in. w.c. (2.74 kPa)
Min. Supply Pressure for
Purpose of Input Adjustment 7 in. w.c. (1.74 kPa) 11.0 in. w.c. (2.74 kPa)
Orifice Size DMS # 36 DMS # 52
Nominal Input Rating 30,500 BTU/hr 30,500 BTU/hr
Minimum Input Rating 20,600 BTU/hr 17,200 BTU/hr
Altitude 0 - 4,500 ft. (0 - 1372 m) 0 - 4,500 ft. (0 - 1372 m)
Primary Air Opening 50% (Minimum) open
Electrical Rating 120 V.A.C. System 120 V.A.C. System
HIGH ALTITUDE INSTALLATION
When installing this appliance beyond 4500 . (1372 m) above sea level, the appliance must be properly de-rated
and installed according to local codes, in the absence of local codes, with the current National Fuel Gas Code,
ANSI Z223.1/ NFPA 54, in the US or Installation Code, CSA-B149.1, in Canada.
CAUTION
• Due to high temperatures, the appliance should be located out of traffic and
away from furniture and draperies.
• Children and adults should be alerted to the hazards of high surface temperature
and stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room
as the appliance.
• Clothing or other flammable material should not be placed on or near the
appliance.
• Installation and repair should be done by a qualified service person. The
Appliance should be inspected before use and at least annually by a
professional service person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etcetera. It is imperative that
control compartments, burners and circulating air passageways of the appliance
be kept clean.

OM-1606 E V1.03 April 2, 2014
Page 7
TORINO II Freestanding 1606
APPLIANCE DIMENSIONS

OM-1606 E V1.03 April 2, 2014
Page 8 TORINO II Freestanding 1606
INSTALLATION CLEARANCES
CLEARANCES TO COMBUSTIBLES
MODEL - Torino II
A Alcove Width min. 46-3/8” (1178 mm)
B Alcove Height min. 48” (1219 mm)
C Top of Unit to Alcove Ceiling min. 12-1/2” (318 mm)
D Side of Unit to Sidewall min. 10” (254 mm))
E Alcove Depth max. 37” (940mm)
F Back of Unit to Back Wall min. 6” (152mm)
G Corner of Unit to Side Wall min. 4-3/8” (111 mm)
Vent 1” (25 mm) to outside surface
Note: Check local codes for oor requirements.
is replace is suitable for installation on a combustible surface.
Fig.2

OM-1606 E V1.03 April 2, 2014
Page 9
TORINO II Freestanding 1606
ASSEMBLY INSTRUCTIONS
GLASS DOOR REMOVAL
Removing the Glass Door:
1. Open the right side panel.
2. Unhook the door latch.
3. Swing the door open.
4. Using a screw driver, remove the top glass retainer, making sure to hold the glass from falling out.
5. Li out and remove door glass with the gasket attached.
6. If the glass door is damaged, it must be replaced with another glass door certied with this appliance only
7. Replacement glass doors are available through your Blaze King dealer see “REPLACEMENT PARTS” on
page 43
Replacing the Glass Door:
1. Check the condition of the glass and the gasket before installing door.
2. Replace the window glass and gasket and re-install the top glass retainer.
3. Swing the door shut and re-attached the door latch.
If the glass has been damaged contact your dealer and replace the glass and gasket with a new glass and gasket
provided by your dealer.
WARNING:
• Do not use any substitute materials for glass components.
• Do not abuse glass door such as striking or slamming shut.
• Do not operate this appliance with cracked or broken glass.
• Clean glass with a so, non-abrasive cloth and water or a suitable, mild, non-abrasive cleaner.
• Do not use abrasive cleaners.
• Do not clean or remove glass when the appliance is hot.
WARNING:
Do not operate appliance with the glass front removed,
cracked or broken. Replacement of the glass should
be done by a licensed or qualified service person.

OM-1606 E V1.03 April 2, 2014
Page 10 TORINO II Freestanding 1606
ASSEMBLY INSTRUCTIONS cont.
PLACEMENT OF LOGS
WARNING :
Do not place the logs in any other conguration than the one shown.
Fire, explosion or excessive carbon monoxide (CO) may result,
causing property damage, personal injury or loss of life.
Step 1: Place rear log on log on pins
near the rear center of the burner.
Step 3: Install pins in holes “arrows”
and place nal log on pins as shown.
Step 2: Install pins in holes “arrows” and
place next log on pins and log support.

OM-1606 E V1.03 April 2, 2014
Page 11
TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS
PRECAUTIONS
• is appliance must be installed by a qualied gas installer and the installation conform to the
installation codes.
• is appliance needs fresh air for safe operation and must be installed so there are provisions for
adequate ventilation air. Provide adequate clearance around air openings of the appliance. Never obstruct
front openings.
• Provide adequate clearances for proper operation and servicing of the appliance.
• is appliance must be properly connected to a venting system.
• is appliance must NOT be connected to a chimney ue serving a solid-fuel appliance.
LOCATING GAS FIREPLACE
e venting system of this appliance must be installed in a location that is free of plumbing, electrical wiring
and heating or air conditioning ducts. Select a location that is accessible for venting. See “ALLOWABLE
TERMINATION LOCATIONS” on page 40, in this manual.
Mobile Home Installation:
Two holes are provided in the pedestal base of the unit to allow for anchoring down the appliance. To access the
mounts simply remove the pedestal back panel, or li o the pedestal valve access panel at the front of the unit.
e pedestal back unscrews with 4 screws, the pedestal front lis o 2 hooks and 2 magnets. Li up and pull
towards you.
VENT TERMINATION LOCATION
1. Establish a suitable vent termination location, see “ALLOWABLE TERMINATION LOCATIONS” on
page 40
2. In heavy snowfall areas make sure vent termination is located where it can not be blocked by snowfall or
snow from snow removal equipment.
3. Locate vent termination away from plants, bushes or any other object on or near the vent termination
that will interfere or obstruct the air ow around it.
4. DO NOT recess vent termination into walls, sidings or planters.
5. Vent terminations located below 7  (2130 mm) from grade level or anywhere that it is a burn hazard to
the public, such as patios and balconies, must be protected with an approved termination cage.

OM-1606 E V1.03 April 2, 2014
Page 12 TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
GAS CONNECTIONS
Have your gas supplier or a qualied gas tter run a gas supply line into the gas replace. e line must be
properly sized and tted according to the installation codes. Upstream of the supply connection, the tter shall
provide a manual shut-o valve.
CAUTION:
The appliance and its individual shutoff valve must be disconnected from the gas
supply piping system during any pressure-testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa). The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure-
testing of the gas supply piping system at test pressures equal to or less than 1/2
psig (3.5 kPa). Failure to do so will damage the appliance’s gas valve. Such damage
is not cover by the manufacturer’s warranty.
BE SURE TO TIGHTEN THE PRESSURE TAP SET SCREW AFTER CHECKING THE PRESSURE.
Before connecting the appliance to the gas supply line, double check that the appliance you have purchased is
designed for the gas type you are using. e gas type markings are located on the certication label and also on
the appliance’s gas valve.
Adequate clearance for proper installation and checking of the
gas connections must be provided. All gas connections must be
checked for gas leaks.
Pedestal Access
e pedestal / gas controls can be accessed for set up or servicing
and adjusting. e pedestal rear cover can be removed with 4
screws, while the front lis o 2 hooks and magnets. Use care
when removing these parts that you do not accidentally scratch
the paint on the pedestal base. When the covers are removed,
you should have easy access for connections and testing
purposes. Re-install these components aer servicing, again,
being careful not to damage the painted services of the stove.
• Check for proper gas supply pressure by loosening the set screw on supply pressure tap on the gas valve
with a small at tip screw driver and placing a test gauge on the tap.
• Check for proper gas supply pressure by loosening the set screw on supply pressure tap on the gas valve
with a small at tip screw driver and placing a test gauge on the tap.
• e minimum permissible gas supply pressure is 5.0 in. w.c. (1.24 kPa) for natural gas and 12.0 in. w.c.
(3.0 kPa) for propane. Maximum gas supply pressure should never exceed 14.0 in. w.c. (3.48 kPa) or 1/2
psi. for both natural gas and propane.

OM-1606 E V1.03 April 2, 2014
Page 13
TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
WARNING:
A minimum clearance of 1” to combustibles must be maintained on
vertical pipe runs and 2” for horizontal pipe runs (sides and bottom 1”)
e rigid vent systems use twist lock connections. e adaptor attached to the unit connects to the approved
venting system. While you are assembling the pipe bear in mind the best visual appearance. Seams should be
aligned and hidden as much as possible. Make sure you twist the mating section all the way to make a solid
connection.
As this system is a sealed system, a high temperature sealing compound
must be used to seal the metal to metal joint:
Apply a bead of high temperature sealant (non-silicone) to both the 4”
exhaust and 6-5/8” intake section of the male pipe. e female section of
the pipe/tting has four indentations evenly spaced around the pipe. ese
indentations are designed to slide over the male section of the pipe and
locate into the four entry slots of the male section of pipe. Twist the female
section clockwise a quarter turn to fully lock the sections together.
Horizontal Wall Vent Terminations
e position of the horizontal vent termination must be positioned to meet all local building codes, see
“ALLOWABLE TERMINATION LOCATIONS” on page 40. Attach the correct length of vertical section pipe
and an elbow tting to the stove. Mark the center line of the pipe facing the wall (allowing for a 1/4” rise per
foot of horizontal run). Example 10  of horizontal would require a rise of 2.5”.
NOTE: Allowing the vent pipe to slope down towards the vent termination could cause
poor combustion and/or high temperatures that may present a fire hazard.
Mark a 10” x 10” square around the center mark (inside dimensions). Cut and frame the exterior wall to accept
the wall penetration heat shield. Install the penetration shield using wood screws. If the wall being penetrated is
constructed of non-combustible material a 7” hole sucient for the vent pipe, is acceptable.
CAUTION: When installing the termination on to vinyl siding, a vinyl siding kit must be used.
This prevents the termination from being recessed into the siding.
When the termination is to be attached to vinyl siding apply a bead of non-hardening mastic around the outside
edge to form a seal between the stando and the termination cap. Attach the termination cap to the exterior wall
inserting four wood screws through the holes in the corner of the vent termination. Complete the installation by
applying a bead of mastic around the outer edge of the vinyl stando.
With the termination cap installed you can now connect the completed vent assembly by sliding the unit back
towards the wall and carefully inserting the pipe into the terminal. Before the nal connection is made slide on
the decorative wall thimble. Secure the termination cap by securing the termination straps to the pipe as close
to the exterior wall as possible using sheet metal screws. Ensure that the straps are hidden by the wall thimble
cover. Apply decorative trim if required.
High
Temperature
Sealant
(Mil-Pac)
DO NOT USE
SILICONE
BASED
SEALANTS

OM-1606 E V1.03 April 2, 2014
Page 14 TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
Vertical Installations
Always maintain the 1” clearance around the vent pipe (vertical), when passing through ceilings, walls, roofs,
enclosures, attic raers or any combustible surfaces.
DO NOT PACK AIR SPACES WITH INSULATION.
Refer to the vent chart for maximum allowable vertical and horizontal
installations.
When planning your installation determine if ceiling joists, roof raers
or other framing will obstruct the vent system. You may have to use 45°
elbows to navigate around any obstacles. When passing through a at
ceiling install a Box/Wall thimble. Cut a 10” square hole and frame as
shown in the diagram opposite.
Ensure all pipe sections are fully twist locked.
NOTE: Always check your local codes before installing venting. Necessary clearances and
requirements may vary from state to state(province to province).

OM-1606 E V1.03 April 2, 2014
Page 15
TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
rough Roof Framing
Maintain 10” opening relative to the
pitch of the roof.
Install the ashing with upper portion slid
under the roong material and the lower
portion over the roong material.
Note: Do not fasten down until the
final adjustments to the vent have
been made.
Use a suitable round or square
support through the roof. Ensure
adequate heat shield protection is
provided.
Termination Above Roof
Consult local codes for minimum vent
cap height above the roof, vent must be a
minimum 2’ from any wall.

OM-1606 E V1.03 April 2, 2014
Page 16 TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
VENTING
is appliance will not function without being connected to a proper venting system. is unit can be used with
Selkirk (Direct-Temp), American Metal, Security Chimneys or Simpson Duravent 4” x 6-5/8” venting. Read
the manufacturer’s installation instructions before installing the venting system.
Typical Installation
- 24”(min) vertical vent pipe on top of the appliance,
- One 90° elbow, and up to 24” (max) horizontal run to the outside (with a 2’ vertical rise).
Other installations
• Up to 4 - 90° elbows, or equivalent, maximum.
• Minimum 2’ (610mm) straight length between bends.
• e total vertical height up to 30’ (9.14 m) maximum.
• Use vent restrictor over 20’ vertical height .
• e total horizontal run up to 16’ (4.88m) maximum.
• Note: 2’ (0.6m) minimum of vertical height required.
NOTE: Maximum vent lengths may be subject to local codes.
For best venting performance, here are some general venting rules:
1. Use only vent systems and components certied for use with this appliance.
2. Maintain a minimum of 1” (26 mm) clearance to combustibles from the outside surfaces of vertical vents
and minimum of 1” (26 mm) sides and bottom, and 2” (51 mm) from top surfaces of horizontal vents.
Always use a wall thimble when passing through combustible construction.
3. Observe all local code restrictions, if any, regarding the installation of this type of gas appliance.
4. Observe the vent height and length restrictions given in this manual.
5. Never slope horizontal vents downwards.
6. Maintain at least an upward slope of 1/4” (7 mm) for every 1  (305 mm) of horizontal vent.
7. Terminate the vent with a termination certied for use with this appliance.
8. Support horizontal vent every 3  (915 mm) to prevent it from sagging.

OM-1606 E V1.03 April 2, 2014
Page 17
TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
VERTICAL VENTING
Example 1
V Value = 3A (12’) + 1C (3’) = 15’
H Value = 2B (4’) =4’
V Value = Total length of all vertical sections in feet.
H Value = Total length of all horizontal sections in feet.
Note:
• for H & V values for 45º venting, see Chart IV
“INSTALLATION INSTRUCTIONS cont.” on page 19
• elbows are not counted in H or V values
• vent chart starts from the top of the unit

OM-1606 E V1.03 April 2, 2014
Page 18 TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
Vent Restrictor (P/N 1851)
Due to the extra ow produced by certain venting congurations a vent restrictor must be placed in the vent to
maintain performance. All top vent installations over 20’ require the use of a 60% restrictor. e restrictor is
installed in the exhaust of the appliance as shown in Figure’s 4, 5, and 6.
If a restrictor is necessary it can be installed in the following order:
1. Turn o the appliance and allow it to cool to room temperature.
2. Carefully remove the logs and brick panels and place them in a safe location.
3. Remove the “FIREBOX BAFFLE” (4 screws). (Fig. 4)
4. Remove six screws from the “FIREBOX TOP”. (Fig. 5)
5. Install the “VENT RESTRICTORS” in the air intake (6 screws). (Fig. 6)
6. Re-install the “FIREBOX BAFFLE”. (Fig 4)
7. Install the logs.
Fig. 4 Fig. 5
FIREBOX BAFFLE
1
2
3
4
5
6
FIREBOX TOP
VENT
RESTRICTORS
Fig. 6

OM-1606 E V1.03 April 2, 2014
Page 19
TORINO II Freestanding 1606
INSTALLATION INSTRUCTIONS cont.
Typical vent Installation
High Wind Vertical
Termination Cap
Flashing
Twist Lock
Joints
Wall Thimble or
Fire-Stop
Alternate 45° pipe
requiring strap
support
CHART IV

OM-1606 E V1.03 April 2, 2014
Page 20 TORINO II Freestanding 1606
RIGID VEN
T
ING PAR
T
S LIS
T
SIMPSON DURAVENT DIRECTVENT PRO / GS SYSTEM PARTS LIST
Description Part # Old Part #
Horizontal Termination Kit - In Canada—Mandatory to add a wall thimble (46DVA-
KHC.) 46DVA-KHA 971
Vertical Termination Kit - 978
6” Pipe Length -Black 46DVA-06B 908B
6” Pipe Length –Galvanized 46DVA-06 908
8,5” Black Extension (3”-7”) 46DVA-08AB -
8,5” Galvanized Extension (3”-7”) 46DVA-08A -
9” Pipe Length-Black 46DVA-09B 907B
9” Pipe Length-Galvanized 46DVA-09 907
12” Pipe Length-Black 46DVA-12B 906B
12” Pipe Length-Galvanized 46DVA-12 906
16” Black Extension (3”-14.5”) 46DVA-16AB -
16” Galvanized Extension (3”-14.5”) 46DVA-16A -
24” Pipe Length-Black 46DVA-24B 904B
24” Pipe Length-Galvanized 46DVA-24 904
36” Pipe Length-Black 46DVA-36B 903B
36” Pipe Length-Galvanized 46DVA-36 903
48” Pipe Length-Black 46DVA-48B 902B
48” Pipe Length-Galvanized 46DVA-48 902
11”- 14 5/8” Adjustable Pipe Length-Black - 911B
17”- 24” Adjustable Pipe Length-Black - 917B
45° Elbow-Black 46DVA-E45B 945B, 945BG
45° Elbow-Galvanized 46DVA-E45 945, 945G
90° Elbow-Galvanized 46DVA-E90 990, 990G
90° Elbow-Black 46DVA-E90B 990B, 990BG
Vertical High Wind Termination Cap (must be used for all vertical terminations) 46 DVA-VCH 991
Horizontal. DV Termination with 1” return - 984GL
Horizontal. Square Termination Cap - 984
Horizontal. Square High Wind Termination Cap 46DVA-HC 985
Horizontal round termination cap 46DVA-HRCS -
Sconce Termination Cap 46DVA-HSC -
Wall Thimble Cover—Support Box 46DVA-DC 940
Cathedral Ceiling Support Box 46DVA-CS 941
Brass Trim fro Ceiling Support Box - 3951
Firestop Spacer 46DVA-FS 963
Flashing 0/12-6/12 46DVA-F6 943
Flashing 7/12-12/12 46DVA-F12 943S
Storm Collar 46DVA-SC 953
Vinyl Siding Standoff 46DVA-VSS 950
Wall Strap 46DVA-WS 988
Wall Pen Heat Shield (Wall Thimble) 46DVA-WT 942