Blofield DoNuts Solids User manual

DoNuts
Instruction
Manual

1.Take the cover out of the box
and place it on a clean surface,
with the holes for the valves
upwards.
2.The inaon valve is on the
right side. Make sure the pin
is in the closed/up posion.
If this is not the case turn the
pin clockwise. The valve on
the le is a safety valve to
control overpressure.
3. Inate the Tube with the
inaon side of the pump.
Screw the nozzle clockwise
to lock the hose in the valve.
Make sure the cover is always
spread evenly over the inner
tube. (When the cover needs
to be posioned on the tube,
see manual chapter 3. Cover
Assembly)
4. Inate the tube unl all the
wrinkles have disappeared.
This takes approximately 2
minutes. You can’t overinate
the Donuts because of the
safety valve.
5. Turn the tube upside down. 6. Now place the table on the
tube. It is best to do this with
2 persons.(When the metal
axles are not inserted, see
manual chapter Axles inser-
on)
7. Fasten the table by com-
pressing the pins and posion-
ing the stainless steel U-sec-
ons over them.
8. Make sure the pins click into
the holes on both sides, and
are fully extracted.
1. Donuts Build-up

2. Donuts Break Down
1. Dismantle the table by
compressing the pins of the
axles and lt the table feet
outwards.
2. Remove the table from the
cover. It is best to do this with
2 persons.
3. Li the Tube with cover
where you can see the agtag.
The valves are located near
the agtag.
4. Now press the pin and turn
an-clockwise to set the pin
in deate posion. The tube
starts to deate. The process
of deang can be quickened
by deang with the pump.
5. While deang fold the
cover. It is best to do this with
2 persons. The cover can be
folded in three mes.
6. Aer folding the cover press
the pin an turn it clockwise to
close the valve.
7. Place the folded cover into
a crate or box for storage.

1. Take the cover out of the
box and place it on a clean
surface, with the hole for the
valves upwards. When neces-
sary, open the zipper com-
pletely.
2. Take the tube out of the box
and place it on the cover, with
the valves upwards and just
above the holes in the cover.
3. Insert the tube in the cover
and posion the valves on the
two holes of the cover.
4. The Tube can be inated
with the inaon side of the
pump. Screw the nozzle clock-
wise to lock the hose in the
valve. Inate the tube unl it’s
geng its round shape. Make
sure you don’t inate the tube
to much, because that will
make it impossible to move
the cover.
5. Now that the tube has tak-
en on his round form you can
pull the cover on its place and
close the zipper. Make sure
the cover is always spread
evenly over the inner tube.
6. Inate the tube unl all the
wrinkles have disappeared.
This takes approximately 3
minutes.
7. Turn the tube upside down. 8. Insert a stainless steel axle
in each of the three table
mounng points.
9. Push the axles in by hand
while holding the locking strip
with you nger.
10. Make sure the axles are
centered in the mounng
point.
3. Cover Assembly

* Donuts oat, but use on water is at own risk
* Never inate or deate the tube with the table
sll aached on it.
* Never open the zipper while the tube is fully
inated.
* Sharp and/or burning objects can lead to irreplac-
able damage to the table as well as the tube and
cover.
* Avoid dragging the table on abrasive surfaces.
* Never place the table on the ground unprotected,
to avoid scratching on the legs of the table.
*When used on grass, it is recommended to move
the table once in a while in order to avoid suaco-
on of the grass.
* Do not sit or stand on the table top.
* Because of the safety valve and best quality of
fabrics it is no problem to leave Donuts in the sun.

Property
All intellectual property rights in relation to the product, including but not limited to, author’s rights and model rights, lie with the manufac-
turer, Blofield® and it is not allowed to either wholly or partially copy, make public or imitate the product without the expressed prior written
consent from the legal owner. The name and the Blofield® logo are registered Blofield® trademarks.
contact
DoNuts Consumer Manual
Version 1.1
© 2012 Blofield, The Netherlands
www.blofieldusa.com
The Blofield USA Customer Service can be reached with the following information.
Blofield USA Customer Service
[e-mail]
www.blofieldusa.com