Argos Cheval 147/3100 User manual

MADE IN
BRITAIN
Dimensions
Width - 38.5cm
Depth - 36cm
Height - 58cm
Cheval - Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 13/03/14
Important - Please read these instructions fully before starting assembly
ALR2968
147/3100
152/7939
146/1480
152/8794
Issue 2 - 13/03/14 - 6 Wedgefixes added.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 12kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2734A)
(383 x 360mm)
Right Side (D2735A)
(562 x 318mm)
Rail (D2737A)
(348 x 66mm) x 2
Drawer Front (D2738A)
(364 x 164mm) x 3
Drawer Base (T322-297)
(322 x 297mm) x 3
Back (X515-370)
(515 x 370mm)
Left Drawer Side (W300-124LH)
(300 x 124mm) x 3
Right Drawer Side (W300-124RH)
(300 x 124mm) x 3
Left Side (D2736A)
(562 x 318mm)
456
7 8 9
10
Drawer Back (W311-124)
(311 x 124mm) x 3

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 14
D E
Large locking
nut (F900) x 8
F
G H I
K
Small locking
nut (F3) x 6
C
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
see malibu fitment mk2 for large number of panels and fittings
9mm Screw (F74) x 6 9mm Screw (F73) x 12
L
Knock-in Peg (F171) x 12
Plastic Nail (F91) x 4
Drawer runner (F1004) x 6
Handle (F273) x 3
19mm Screw (F461) x 6
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 12
M
Wedgefix (F639) x 6

5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3
x 3
B
B
B
E
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into each of the 3 drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
E
7
8
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
5
E
E
7
8
E
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
EE
78
B
B
5
7
8

K
5
Assembly Instructions
5
Step 4
K
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 7
9
7 8
5
6
7 8
9
6
6
K
7 8
K
x 3
x 3
9
7
8
7
8
9
6
K
Step 6
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
L
G
5
x 3
x 3
5
G
G
L
M
M
M
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
M

Finished
front edge
Assembly Instructions
6
Step 8
Finished
front edge
I
J
I
J
I
J
I
J
D
D
I
I
I
D
Prepare the left side
a: Place 3 runners on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 2 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
1
I
I
D
1
1
J
J
B
1
a:
b:
c:
B
B
1
1
1

Assembly Instructions
7
Step 9
x 2
Finished
front edge
I
J
Finished
front edge
I
J
I
J
I
J
Finished
front edge
Finished
front edge
D
D
B
B
Prepare the right side
a: Place 3 runners on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 2 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
2
I
I
D
2
2
J
J
B
2
a:
b:
c:
2
2
2
I
I
I

A
Assembly Instructions
8
Step 10
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels
into each rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into each rail .
A
4
D4
4
x 2
4
4
2
4
4
Fit the 2 rails
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to each rail
. .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
D
4
Step 11
D
B
4
2
D
Fit the left side
Push the left side
onto the 2 rails .
Use a screwdriver to
tighten the large locking
nut fitted to each rail
. .
D
4
Step 12
1
4
1
Note: Support this
rail until the left
side has been fitted
in the next step.
Note: The 2 rails can have
a plain chipboard surface.
Plain
chipboard
surface

Assembly Instructions
9
Step 13
x 2
B
B
B
B
Finished
front edge
Prepare the top
Screw 4 metal dowels
into the top .
B
3
3
1
2
3
Fit the top
Push the top onto
the sides and .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each side and .
Step 14
3
1 2
D
1 2