Bluedri BD-LGR75C User manual

LGR Dehumidifier Owner’s Manual
115v Model: BD-LGR75C
Please read this owner’s manual
before operating and keep
safe for future reference

- 1 -
GENERAL INFORMATION
Thank you for choosing our LGR Dehumidifier
This Owner’s Manual will provide you with valuable
information necessary for the proper care and maintenance of
your new dehumidifier.
Please take a few moments to read the instructions thoroughly
and familiarize yourself with all the features and operation of
this dehumidifier.
Unpackaging the dehumidifier
Please do not dispose of any packaging until you have checked
the appliance is operational.
After removing the packaging ensure the contents are intact
and complete. In the unlikely event of missing parts; contact
your retailer.
Do not leave children unattended with any of the packaging
since it is a potential source of danger. Disposal of all packaging
must be carried out responsibly & safely and in accordance
you’re your local authority regulations.
Always recycle the packaging material where possible.When
using any electrically powered product, basic safety precautions
should always be followed.
PLEASE READ THESE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT.

- 2 -
When using any electrical appliance,
Basic safety precautions should always be followed.
IMPORTANT INSTRUCTIONS
WARNING - to reduce the risk of fire, electrical shock or injury
to persons or property:
1Always operate the product from a power source of the
same voltage, frequency and rating as indicated on the
product identification plate.
2Close supervision is necessary when any product is used by
or near children the elderly or the infirm. Do not allow
children to use the appliance as a toy.
3This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
4Do not operate any product with a damaged power cord or
plug, after the product malfunctions, dropped or damaged
in any way. Return the complete product to the place of
purchase for inspection, repair or replacement.
5To reduce the risk of electric shock, do not expose the unit
or flexible cord to moisture of any kind.
6Switch off and unplug from the power socket when not in
use, before assembling or before cleaning.

- 3 -
IMPORTANT INSTRUCTIONS
7Do not place objects on the product or allow objects to
obstruct the inlet or outlet openings, or operate in close
proximity to walls or curtains, etc.
8The use of attachments or accessories not recommended
or sold by the product distributor may cause injury to
persons or damage to property.
9Do not attempt to dismantle the appliance.
10 Do not operate the appliance on a metal surface.
11 Do not use the appliance in artificially hot or humid
conditions or allow to be used in a hazardous environment.
Consult the product Specifications section for approved
operating conditions.
12 Do not clean the appliance with organic solvent.
13 This Owner’s Manual is an integral part of the appliance
and should be stored for safe keeping and must always
accompany the appliance in the event of ownership
transfer or for reference to by a service engineer.
Typical 3 prong
plug and outlet

- 4 -
Control panel
Filters
Air intake
metal grill
Water pipe
Storage location
Water
pipe
Water pipe Connector
(Female)
Pull rod
Rating label
Wheel
PRODUCT IDENTIFICATION
Domed decal
Air outlet
Power cord
fixed support
Power
cord
Water pipe
connector
(male)
FIG.A: FRONT
FIG.B: REAR

- 5 -
SETTING UP INSTRUCTIONS
SETTING UP THE DEHUMIDIFIER
WARNING
No not obstruct the air intake or air outlet
IMPORTANT
Place dehumidifier in the upright position. When
transporting a dehumidifier to site, allow the
dehumidifier to stand for 30 minutes before switching
ON. This is necessary to allow the refrigerant system to
stabilize and avoid system damage.
PLACE IN ENCLOSED AREA: For best results, operate the
dehumidifier in an enclosed area to create a "drying chamber."
Close all doors and windows that open to external areas to
maximize the dehumidifier’s water removal efficiency. Keep
traffic through the drying chamber to a minimum. Place the
dehumidifier in the center of the room away from walls and
furnishings where airflow may be obstructed.
PROPER AIRFLOW IS ESSENTIAL: Do not place this dehumidifier
in a position where the front Air Intake Grill or rear Air Outlet is
blocked by walls, furniture or any other obstruction.

- 6 -
Air Outlet
Attach Ductwork
16.5FT. MAXIMUM
Front Air
Intake Grill
SETTING UP INSTRUCTIONS
Illustration of correct positioning for best performance
ENSURE PROPER ATTACH DUCTWORK: This dehumidifier can
attach diameter 0.558 foot air outlet ductwork to satisfy the
needs of different places. To avoid airflow restrictions , Do not
attach exceed a 16.5 foot length ductwork, the ductwork
ensure do not winding .
.
KEEP CLEAR AND
NO NOT WINDING
KEEP CLEAR

- 7 -
SETTING UP INSTRUCTIONS
ENSURE PROPER DRAINAGE: This dehumidifier contains a
built-in pump that connects to a drainage hose which is stored
in the back of the unit. Uncoil the entire hose to ensure that
there are no kinks or restrictions and place the unattached end
into a drain or run to the outdoors. Ensure that water piped to
the outdoors does not create a slipping hazard. To avoid
damaging or overworking the pump, do not exceed a 10 foot
vertical lift height between the pump and drain.
10 FT. MAXIMUM
DRAIN HEIGHT
To Drain
Rear Drain
Hose Outlet
Drain
Hose

- 8 -
CONTROL PANEL
Digital Control Panel
ON/OFF: Press once to turn the unit ON or OFF.
PURGE: Press the “PURGE”key to empty water
from the pump reservoir. During normal operation the
pump purges automatically when the reservoir is full. Use
“PURGE” before moving the machine to avoid water
spillage. The pump will close automatically after forty
seconds continuous operation.
FUNCTION: Press the “FUNCTION”key, The screen
will display ‘Humidity setting’ ‘Ambient humidity’ ‘Total
running hours’ ‘Ambient temperature’.
REGULATE: Press “REGULATE”key to adjust humidity
or set total running hours and job hours or setting
fahrenheit and centigrade.
Long press “REGULATE”key 5 seconds, The coil sensor
temperature will display. The screen will return to display
ambient humidity after coil sensor temperature cursor
flashing 3 seconds.
Coil Sensor Temperature

- 9 -
CONTROL PANEL
The LCD displays symbols
: Dehumidify ON.
: Defrost ON.
: Draining.
: Fan start up
: Setting humidity.
: Ambient humidity.
: Total running hours.
: Ambient temperature.

- 10 -
OPEARTION
Plug in electrical cord
This dehumidifier must be plugged into a grounded
polarized 115 VAC/60Hz outlet rated at least 15 amps.
Make sure the drain hose is connected and routed to
a safe location.
Plug in electrical cord, The screen will display standby:
Turn the unit ON
Press the “ON/OFF”key to turn the unit on.
If humidity setting is less than ambient humidity, the unit
will entry to dehumidify mode. The screen will display:
If humidity setting is greater than ambient humidity, the
unit will stop working after started 1 minute.
Turn the unit OFF
Press the “ON/OFF”key to turn the unit OFF. When the
unit turns OFF, The water pump will turn on automatically
for 40 seconds to drain the residual condensate water in
the dehumidifier. The screen will appear draining
cursor.

- 11 -
IMPORTANT:
To avoid water spillage. Do not move the dehumidifier for
at least three minutes after turning the power off. Before
transporting, be sure to remove the external drain hose,
drain it carefully, and return it to the pocket provided on the
back of the unit.
OPEARTION
Humidity setting
The factory setting is continuous. The humidity can be set in
the following manner:
1. Press the function key , The humidity setting the
cursor flashing.
2. Press the regulate key to setting the desired humidity
level. Increases or decreases are in increments of 5%.
Adjust humidity is between CO, 25% and 95%.
3. Wait 3 seconds after setting the desired humidity is
completed, the unit will automatic recognition of
numerical.
NOTES:
1. When the adjusting humidity is between 25% and 95%.the
unit will stop working while reaching the setting humidity,
the screen will displays :
NOTE:
The fan will start up 1minute after every
30minutes, It can increase validity of the
humidity sensor. The unit will automate resume
operation after detecting the condition
humidity above the setting humidity.

- 12 -
OPEARTION
2. When the adjust humidity is below 25% . the “CO” will be
displayed. The unit will entry to continuous dehumidify
mode .
Total running hours display and job hours display
setting
1. Press the function key twice, the cursor turns to the
total running hours , The total running hours the cursor
flashing.
2. Press the regulate key to switch to job hours.
3. Wait 3 seconds after switch to job hours is completed,
the unit will automatic recognition of numerical.
For example as follows:
Total running hours 200h Job hours 8h
NOTE:
The “Total running hours” field displays continuously during
operation. Like a car odometer, this shows the total number of
hours on the unit and cannot be manually reset outside the
factory.

- 13 -
OPEARTION
Centigrade and Fahrenheit setting
1. Press the function key thrice, the cursor turns to the
centigrade , The centigrade the cursor flashing.
2. Press the regulate key to switch to fahrenheit.
3. Wait 3 seconds after switch to fahrenheit is completed,
the unit will automatic recognition of numerical.
For example as follows:
Centigrade 25 Fahrenheit 77

- 14 -
MAINTEANCE
Cleaning Or Replaced Filter
NOTE: The working performance of the dehumidifier will be
greatly reduced if the filters are clogged. Check filter weekly.
Cleaning or replaced filter if get clogged.
Ensure the dehumidifier is turned OFF and plug is removed
from the power outlet before performing maintenance.
1. Remove the filter as shown.
2. Vacuum any debris from the filter.
3. Using lukewarm water and a mild detergent wash the filter
and allow to dry.
4. Once dry, re-install the filter into the dehumidifier.
The item 2、3 refer only to type of can cleaning filter .

- 15 -
STORING THE UNIT
Storing the unit
Follow the guidelines below when
storing the unit:
1. Prior to storing the unit, clean filters
and drain water from the unit.
2. Wind the power cord to the back
of the unit.
3. Put the water pipe to the water
pipe storage location for front
of the unit.
4. If necessary, stack machines as shown.
NOTE:
Do not stack more than 2 machines
high. Be sure to secure the machines
to ensure they do not fall or move.

- 16 -
TROUBLE SHOOTING
FAULT
CAUSE
SOLUTION
Unit does not
operate
No power to machine.
Unit not switched on.
Plug in unit; check power at
outlet and at base of unit.
Switch unit on.
Fan not
turning
Obstructed air
outlet and fan.
Remove obstruction.
Unit
operating,
but room not
dry
1. Not enough time
to dehumidify air.
2. Poor air movement
in room.
3. Excessive moist air
infiltration in room.
1. Allow more time for
drying.
2. Increase air movement
with fans.
3. Reduce outside air
infiltration into the room.
Unit collects
too little
water
1.Room air is dry.
2.Obstructed filter
and coils
3.Room temperature
is too low.
1.Check humidity with
hygrometer.
2.Check filter and coils;
clean as necessary.
3.Increase room
temperature.
WARNING:
DO NOT attempt to rectify faults using unqualified personnel.
If the problem you are experiencing is not listed here, call your local
distributor

- 17 -
TROUBLE SHOOTING
Fault codes
The table below shows error messages that the system may
report. If the display shows an “ER” message, first unplug the
unit and then plug it back in. This may reset the electronics and
no further action may be necessary. If an error message
reappears, use the table below to help identify the problem.
CODE
ER1
ER2
ER4
Error
message
Coil sensor error
Humidity
sensor error
Water pump fault or
blockage
Display
Reading
Flashes every 1s
Flashes every 1s
Flashes every 1 s
Reason
1.the coil sensor
terminals are not
securely plugged in.
2.The coil sensor fault .
3.If not above question,
It maybe is display
panel PCB fault.
1.The humidity sensor
terminals are not
securely plugged in.
2.The humidity sensor
fault . 3.If not above
question, It maybe is
display panel PCB fault.
Water is not draining
from the pump
reservoir or there is a
lack of power to the
water pump.
Remedy
1.Check to ensure the
coil sensor terminal is
securely plugged in.
2.Replace the coil
sensor .
3.Replace display panel
PCB
1. Check to ensure the
humidity sensor
terminal securely
plugged in.
2.Replace the humidity
sensor .
3.Replace display panel
PCB
1. Make sure
maximum lift is not
exceeded. End of
hose should be no
higher than 10 feet
above the unit.
2. Check pump for
debris or blockage.
If these solutions do not correct the error, contact your local distributor.

- 18 -
SPECIFICATION
Dehumidifying Capacity
(AHAM Conditions-80°F/ 60% RH):
75pints/day
Dehumidifying Capacity
(Saturation Conditions - 90°F/
90%RH):
145pints/day
Power Supply:
115V/60Hz,
625W/5.5A
Refrigerant:
R410A/26.5oz(750g)
Working Temperature:
41°F~95°F
Controls
Electronic Touchpad
Process Air
L-259CFM
H-300CFM
Unit Size(inch ):
19.7x17.9x28
Packing Size(inch):
22.8x18.9x28.5
Net/Gross Weight( lbs):
84/90