Bluestream HEX70SL-KIT User manual

HEX70SL-KIT QUICK REFERENCE GUIDE
contact: [e-mail] | [e-mail]
HEX70SL-KIT
Quick Reference Guide
01
Our HEX70SL-KIT 4K HDBaseT™ extender set oers market leading features in a
slimline chassis. The product delivers HDMI, Bi-directional IR and Bi-directional
PoC up to lengths of 70m.
Introduction
FEATURES:
• Advanced HDBaseT™ technology oering uncompressed video and audio with zero latency
• Extends HDMI 1080p up to a distance of 70m over a single CAT cable
• Supports 4K UHD video up to 40m (3840 x 2160 @30Hz 4:4:4, 4096 x 2160 @24Hz 4:4:4, and 4K @60Hz 4:2:0)
• Supports all industry standard video resolutions including VGA-WUXGA and 480i-4K
• Enhanced slimline chassis
• Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus and DTS-HD
Master Audio transmission
• Bi-directional IR pass-through
• Supplied with Blustream IR receiver and emitter
• Supports bi-directional PoC (Power over Cable) to power extenders from either Transmitter or Receiver end
• Smart EDID function automatically limits EDID to within HDBaseT™ specification to improve compatibility
• HDCP 2.2 compliant

HEX70SL-KIT QUICK REFERENCE GUIDE
www.blustream.com.au | www.blustream.co.uk
02
TX Panel Descriptions
1EDID Selection Button – Cycle through the EDID modes
2HDMI input - connect to HDMI source device
3HDMI signal link indicator
4IR input - connect to Blustream 5V 3.5mm IR receiver
5IR output - connect to Blustream 5V 3.5mm IR emitter
6HDBaseT™ output
7Power over Cable (PoC) switch (ON / OFF) - to enable / disable PoC being sent from the transmitter
812V/1A DC power input screw type connector
9Power status indicator
1HDMI output - connect to HDMI display
2HDMI signal link indicator
3IR input - connect to Blustream 5V 3.5mm IR receiver
4IR output - connect to Blustream 5V 3.5mm IR emitter
5HDBaseT™ input
6Power over Cable (PoC) switch (ON / OFF) - to enable or disable PoC being sent from the receiver
712V/1A DC power input screw type connector
8Power status indicator
4
4
5
5
6
6
7
7
RX Panel Descriptions
2
2
1
1
8
8
93
3

HEX70SL-KIT QUICK REFERENCE GUIDE
contact: [e-mail] | [e-mail] 03
Terminating the Interconnecting HDBaseT™ CAT Cable
It is important that the interconnecting CAT cable between the Blustream HDBaseT products is terminated using the
correct RJ45 pin configuration. The link CAT cable MUST be a ‘straight’ (pin-to-pin) CAT cable and it is advised that this
is wired to the T568B wiring standard as this format is less prone to EMI (Electro-Magnetic Interference).
When installing CAT cables it is advised that you use the best possible CAT cable quality possible. HDMI distribution
products will only work if used with CAT5e standard cable or above. Blustream recommends using a CAT6 (or better)
cable for your installations, especially when running over longer distances, in areas of high EMI, or for 4K signal
distribution.
Understanding the HDBaseT™ Signal Status Lights
The Blustream HDBaseT™ extender solutions include status LED indicators on both the Transmitter and Receiver products to
show all connections are active and to help diagnose possible problems.
Understanding the status lights:
Receiver:
• The HDMI signal link light will be o when there is no connection with a display / sink
• The HDMI link light will be on when there is an active connection with a display
• The orange HDBaseT™ link light will be o when there is no CAT cable / active HDBaseT™ connection on the RJ45 HDBaseT™ output
• The orange HDBaseT™ link light will blink if there is an unstable connection between the Transmitter / Matrix and Receiver
• The orange HDBaseT™ link light will be lit when a CAT cable is connected to the HDBaseT™ RJ45 output on the Transmitter
and an active connection is achieved with the Receiver / Matrix
• The green HDBaseT™ HDCP light will be o when no video signal is received
• The green HDBaseT™ HDCP light will flash when there is video signal without HDCP being received
• The green HDBaseT™ HDCP light will be on when there is video signal with HDCP being received
• The power link light will be o when no power is connected to the Receiver, or to the connected Transmitter unit
• The power link light will be on when power is connected directly to the Receiver or is being received from the Transmitter unit
Transmitter:
• The HDMI signal link light will be o when there is no connection with a source device
• The HDMI link light will be on when there is an active connection with a source device
• The orange HDBaseT™ link light will be o when there is no CAT cable / active HDBaseT™ connection on the RJ45 HDBaseT™ output
• The orange HDBaseT™ link light will blink if there is an unstable connection between the Transmitter / Matrix and Receiver
• The orange HDBaseT™ link light will be lit when a CAT cable is connected to the HDBaseT™ RJ45 output on the Transmitter
and an active connection is achieved with the Receiver / Matrix
• The green HDBaseT™ HDCP light will be o when no video signal is transmitted
• The green HDBaseT™ HDCP light will flash when there is video signal without HDCP being transmitted
• The green HDBaseT™ HDCP light will be on when there is video signal with HDCP being transmitted
• The power link light will be o when no power is connected to the Transmitter, or to the connected Receiver unit
• The power link light will be on when power is connected directly to the Transmitter or is being received from the Receiver unit
RJ45 Wiring - T568B

HEX70SL-KIT QUICK REFERENCE GUIDE
www.blustream.com.au | www.blustream.co.uk
04
Package Contents
Specifications
HEX70SL-KIT
• 1 x HEX70SL-TX and 1 x HEX70SL-RX
• 1 x 12V/1A DC Power Supply
• 1 x IR Emitter
• 1 x IR Receiver
• 2 x Mounting Bracket Sets
• 1 x Quick Reference Guide
Maintenance
Clean this unit with a so, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate.
HEX70SL-TX
• Video Input Connectors: 1 x HDMI Type A, female
• Video Output Connectors: 1 x HDBaseT™ RJ45 connector
• IR Input Port: 1 x 3.5mm stereo jack
• IR Output Port: 1 x 3.5mm stereo jack
• Casing Dimensions (W x D x H): 107 x 16 x 73mm
• Power Supply: 12V/1A DC, screw type connector
HEX70SL-KIT
• Box Dimensions (W x D x H): 250 x 150 x 105mm
• Shipping Weight: 0.75kg
• Operating Temperature: 32°F to 104°F (-5°C to +55°C)
• Storage Temperature: -4°F to 140°F (-25°C to +70°C)
RevA1_HEX70SL-KIT_QRG
HEX70SL-RX
• Video Input Connectors: 1 x HDBaseT™ RJ45 connector
• Video Output Connectors: 1 x HDMI Type A, female
• IR Input Port: 1 x 3.5mm stereo jack
• IR Output Port: 1 x 3.5mm stereo jack
• Casing Dimensions (W x D x H): 107 x 16 x 73mm
• Power Supply: 12V/1A DC, screw type connector
HEX70SL-RX (when sold individually)
• 1 x HEX70SL-RX
• 1 x Mounting Bracket Set
• 1 x Quick Reference Guide
HEX70SL-TX (when sold individually)
• 1 x HEX70SL-TX
• 1 x Mounting Bracket Set
• 1 x Quick Reference Guide