Bluetti EP600 User manual

EP600
Energy Storage System
BLUETTI App User Manual
How to control EP600 ESS via the BLUETTI App.

Contents
Introduction
Getting Started
Download the App
Sign up
Log in
App Languages
Exit
Using the App
Binding
Connection
Energy Monitoring
Settings
Account Security
Modify Avatar & Username
Change Password
Cancel Account
Practices
Prioritize PV Charging
Charge via Grid
Feed to Grid
Offset Peak-hour Energy Usage
3
3
6
3
3
4
5
5
6
8
11
14
Unbind Device 18
Document Center 19
Customer Service 20
20
20
21
21
22
22
22
24
Parallel Management 24
23

Introduction
The BLUETTI application allows you to monitor and control the EP600 energy storage system
(ESS) via Bluetooth or WiFi, with features like Device Control, Real-time Data Collection, Alarm,
Firmware Upgrade, etc.
Download the App
Scan the QR code below to download the BLUETTI App, or search for "BLUETTI" in the App
Store or Google Play.
Supported operating systems: Android 8.0 or above, iOS 11.0 or above.
Getting Started
Sign up
1. Open the app and tap LOGIN/REGISTER.
2. Tap Sign up and enter your email address.
3. Enter the verification code and tick the checkbox.
4. Tap REGISTER to create your BLUETTI account.
1
4
3
2
3

Note: If you don't receive the email with verification code, check your Junk or Spam folder. If
you still can't find the email, try "Get Code" again as there may be a delay. If the code is still
unavailable, please contact BLUETTI customer service for assistance.
Log in
1. Open the app and tap LOGIN/REGISTER.
2. Enter your account details.
3. Tick the checkbox
4. Tap LOG IN.
Note: If you forget your password, tap Forgot Password? to reset it.
Note: If you don't receive the email with verification code, check your Junk or Spam folder. If
you still can't find the email, try "Get Code" again as there may be a delay. If the code is still
unavailable, please contact BLUETTI customer service for assistance.
1
2
4
3
4

App Languages
1. Go to the Me page.
2. Tap Multi-language and select the language you want.
3. Tap OK to save the change.
Exit
1. Go to the Me page.
2. Tap your name and go to the Account page.
3. Tap Sign Out.
1
2
3
5

Binding
Using the App
Note: Before binding, make sure your EP600 ESS is powered on with Bluetooth enabled (if
necessary).
• When you log in and access the My BLUETTI page for the first time, the app will
automatically scan for nearby Bluetooth devices. Select your EP600 ESS from the pop-up list.
You may also opt to bind it via Bluetooth, SN, or QR code.
• Bluetooth
1. Tap the icon in the upper right corner of My BLUETTI page, and then select
from the menu.
Add Manually
6
1
2

7
2. On the Bind page, select your EP600 ESS from the Available Devices list.
Note: Make sure you've enabled Bluetooth and location service (e.g. GPS) on your phone.
If you can't find your EP600 ESS, get closer and Tap to refresh the list (recommended
range: 5m).
• SN
1.Tap the icon on My BLUETTI page, and then select from the menu.
2.At the bottom of the Bind page, tap Add Manually.
3.Enter the device SN and your account in the pop-up, then tap OK to complete the
binding.
Add Manually
1
2

8
Device Sharing
Features Bluetooth connection WiFi connection
Firmware Upgrade
Parallel Management
SoC Setting
Charge &Discharge Time Setting
Real-time Alarm
Battery Pack Status Monitoring
√
√
x
√
√
√
√
√
√
x
√
√
√
√
Connection
The EP600 ESS supports both Bluetooth and WiFi connections. A simple comparison is as
follows:
• QR Code
1.Tap the icon on My BLUETTI page, and then select from the menu.
2.Scan the QR code on the back of your EP600.
Scan
Note: The EP600 ESS can be bound to one account only, while can be shared with
multiple accounts.

9
• Bluetooth Connection
If you've registered your EP600 ESS, go to the My BLUETTI page and tap under its
name. You'll see in the upper left corner of your EP600 ESS's operation status page.
If you haven't registered yet, open the app and tap to connect your EP600
ESS directly. Select it from the Bluetooth Direct Access page.
OFFLINE MODE
Note: Make sure your EP600 ESS is powered on with Bluetooth enabled.
For a stable connection, keep your phone and EP600 ESS close together(recommended
range: 5m).

•WiFi Connection
If you've registered your EP600 ESS, you can also connect to it via WiFi to get the most
out of the BLUETTI app. To get started, you need to configure the network first.
Or, tap the or icon under the EP600 ESS's name to configure the network. You'll also be
taken to the Network settings page and follow the same steps to complete the configuration.
■Configure the network
With a successful binding, you'll be taken to the Network settings page automatically.
Select your WiFi from the available list. Fill in its password in the pop-up, and SAVE it.
It's worth noting that when you connect to the EP600 ESS via Bluetooth, you can also
make changes to the network settings. Tap and go to the operation status page. Tap
the icon and change the configuration in the Network settings section.
Note: The EP600 ESS supports 2.4GHz WiFi only.
10

Energy Monitoring
After you establish a successful connection, go to My BLUETTI page and tap EP600 name
area or the icon and you can view its operation status, including the remaining battery
level, charging and discharging status, battery pack status, and more.
■Connect to EP600
Go to My BLUETTI page, and tap the EP600 name area to connect via WiFi. You'll see
in the upper left corner of operation status page.
11

•Inverter Status
It shows how the EP600 ESS is operating.
Shutdown:
The AC switch is turned off or forced off due to a serious failure.
Off-grid operation:
The AC switch is on, but the system is running off the grid.
On-grid operation:
The AC switch is on and the system is running on the grid. However, it doesn't charge from or feed back
to the grid. The grid can bypass the EP600 inverter and power your loads directly.
On-grid charging:
The AC switch is on and the system is running on the grid. And the system charges from the grid.
On-grid discharging:
The AC switch is on and the system is running on the grid. And the system feeds back into the grid.
Note: When the EP600 ESS is in operation, you can charge it with solar energy anyway.
5. PV
PV (Photovoltaic) charging. To show how much power the
EP600 is drawing from your rooftop solar or solar panel(s).
6. Grid
Charging from or feeding into the grid. To show how much
power the EP600 is drawing from or feeding back into the grid.
7. AC
AC output. This shows how much power the EP600 is supplying
to your devices.
8. Inverter Status 9. Battery Pack 10. Power Statistics
Refer to the following sections.
4. 8%
The remaining battery level.
1.
To check current alarm(s) and alarm history.
2.
To check and change settings.
3.
Bluetooth/WiFi connection successful.
12

Tap the pack you want to check, e.g. Pack 1 to view its operating status.
Model
SN
SoC
BatteryStatus
Battery
Parallel
Fault/Alarm
Protection
Status
Software Version
Battery pack model.
Serial number of the battery pack.
State of Charge. The remaining battery level.
Include Charging, Discharging, and Standby.
The software version of the battery pack.
means that the battery pack is connected in parallel with EP600
means that it's not connected in parallel with EP600.
means that there's no fault or alarm.
means that a fault or alarm occurred. Tap it to view the details.
means that the battery is operating well.
means that it's in a protection status due to a fault or alarm, or
other factors. Tap the icon to view the details.
13
•Battery Pack
It shows the status of connected battery packs. Tap it and go to the Battery Information page.

Settings
Go to the operation status page and tap the icon in the upper right corner. You can
optimize your power usage by customizing relevant settings such as Charge/Discharge
time, SOC High/Low, etc.
14
•Power Statistics
It allows you to view the PV Generation, Grid Consumption, Feed to Grid, and Load Consumption by
day, month, or year.

15
Network settingsTo configure the WiFinetwork. Only available when you
connect tothe EP600 ESS via Bluetooth.
Time Control
Alarm Sound
Carbonemission factor
About Device
To enable the Manage Charge/Discharge Time function
To sound a fault/alarm.
To calculate your reducedcarbon emission.
The information about EP600 and other related devices
Share Device Share EP600 ESS with others (Wi-Fi connection requied).
•AC
The main switch of the EP600 ESS. Keep it on if you want the EP600 ESS to provide AC
output. If it's off, the system has no input or output and will automatically shut down.
Note: If you're updating the firmware, connecting cables, or not using the system, it's
recommended that you turn the AC switch off.
•Manage Charge/Discharge Time
You can set 6 time periods in order, with the earliest as the first and the latest as the last.
1.Turn on the Time Control, and tap Manage Charge/Discharge Time.
2.Select OK in the Attention pop-up.
3.Set a schedule with Charge, Discharge and Default. The Default means the system
doesn't charge or discharge.
Note: Make sure there is no overlap or confusion between different periods.
If you want to charge the system from the grid, you also need to enable the Grid Charge
Enable on the Advanced Settings page. Similarly, to feed excess energy to the grid, turn
on the Feed to Grid.

•SoC Setting (For on-grid EP600 ESS only)
It allows you to set SoC limits for grid charging, grid feed-in, and load supply.
1.Tap SoC Setting and a pop-up shows up.
2.Slide the orange box to your desired SoC High value.
3.Slide the blue box to your desired SoC Low value.
4.Tap OK to save the settings.
SoC High: It's set to 80% by default. This means that the system will stop charging from
the grid when the battery level reaches 80%.
Note: The system acts as the main power source for your home.
SoC Low: It's set to 20% by default. This means that when the batterty level drops below
20%, the system will stop supplying power to your loads and the grid.
Note: The grid will bypass the EP600 inverter to power your loads.
16

•Firmware Upgrade
Go to the Firmware Upgrade page and tap Start to upgrade. Once the upgrade is
completed, it'll prompt that You're up to date.
Note: This feature is only available when you connect to the EP600 ESS via Bluetooth.
17
•Advanced Settings
Go to the Settings page, and tap Advanced Settings to check and change more settings.
Grid Charge Enable
Grid Enhancement Mode
Save AC Switch Status
Meter Switch
Feed to Grid
Multi-inverter Mode
Output Voltage
Output Frequency
Max Grid
Charging Power
Max Charging
Current Of Grid
Max Grid
Discharging Power
Max Discharging
Current To Grid
CT Self-testing
Factory Reset
To enable the EP600 ESS to charge from the grid.
To provide a stable and continuous grid charging.
To save the AC switch status and restore it on restart.
To record the information of generator and PV
inverter, like current, voltage and power.
To enable the EP600 ESS tofeed into the grid.
To enable the EP600 tobe connected and
operated in parallel.
The output voltage of the EP600 ESS.
The output frequency of the EP600 ESS.
The maximum charging power from the grid.
The maximum charging current from the grid.
The maximum discharging power from the
EP600 EES tothe grid.
The maximum discharging current from the
EP600 EES tothe grid.
To check whether the CT is properly connected.
Note toturn AC on.
To factory reset all the settings.

18
You can also unbind it by the following:
1. On the My BLUETTI page, select the EP600 you want to unbind.
a.For an Android phone, long press on the name.
b.For an iOS phone, swipe left the name.
2. Tap Unbind and Tap OK in the Unbind this device? pop-up.
0
Inverter No. Description
The Multi-inverter Mode is off.
The EP600 is used as the host machine.
The EP600 is used as a slave machine.
1
2
Inverter No. : To identify the master and slave machines in parallel mode.
If you connect to the EP600 ESS via Bluetooth:
1. Tap Unbind in the Settings menu.
2. Select OK in the Unbind this device? pop-up.
Unbind Device

19
Document Center
On the My BLUETTI page, tap the icon in the upper right corner to view the product
documents.

Customer Service
On the Services page, tap your product and submit the relavant service requests (e.g.
Installation for EP600 ESS). You can also check the Ongoing and Finished requests.
20
Account Security
Modify Avatar & Username
1. On the Me page, tap on your avatar or name and you'll be taken to the Account page.
2. Tap on your avatar and you're required to take a photo or select an existing photo from
your album. Simply choose the way you like it. As for the name, tap on the Username and
edit a new one. Tap OK to save the changes.