BlueWalker PowerWalker VFI 1000 TG User manual

ENGLISH
PowerWalker VFI 1000-3000 TG/TB/TGS
Quick Guide
I. Panel Description
II. Button
Switch
Function
ON/Silence
Button
By pressing the ON-Button continuously for more than 1 second the UPS system is
turned on.
By pressing this Button an acoustic alarm can be deactivated in the battery mode.
By short touch this Button all acoustic alarms can be deactivated in all modes.
By pressing this Button the UPS can do the battery test in the Line mode or ECO
mode or CVCF mode.
OFF
Button
When mains power is normal, the UPS system switches to No output or Bypass
mode by pressing OFF-Button “ “, and the inverter is off. At this moment, if Bypass
is enabled, then the output sockets are supplied with voltage via the bypass if the
mains power is available.
By pressing this Button an acoustic alarm can be deactivated in the bypass mode.
Release the UPS from fault mode and EPO status.
Select
Button
The output voltage, frequency, Bypass disable/enable and operating mode in No
output or Bypass mode, Battery Ah, Battery remain time display disable/enable and
Charger current in all mode, could be selected by pressing Select-Button, and
confirmed by pressing Enter-Button.
Enter
Button
III. Display
Display
Function
It indicates input voltage/frequency value, which are displayed alternately.

ENGLISH
It indicates the input is connected with mains, and the input power is single
phase input.
It indicates output voltage/frequency value, which are displayed alternately.
It Indicates the operating mode or Fault kind or Warning kind or battery remain
time, several warning kinds at the same time could be displayed alternately.
It indicates the UPS is in setting mode.
It indicates the UPS is in Fault mode or has some warnings.
It indicates the load level. Every
grid represents the level of 20%.
One grid would be displayed if
the level is 0~20%
It indicates the battery Power.
Every grid represents the Power
of 20%.
IV. Rear panel
The graphic below applies to VFI 1000 TG and VFI 1000 TGS. Models of different Power
(2000/3000VA) might have different location of components.
V. Audible alarm function
NO.
Status
Alarm
1
Battery mode
Beep once every 4 sec
2
Battery mode with battery
low
Beep once every sec
3
Bypass mode
Beep once every 2 min
4
Overload
Beep twice every sec
5
Warning active
(see Warning& Fault Code
Beep once every sec

ENGLISH
VI. Operating Modes
The different message/string would be displayed on the LCD screen corresponding to their
operating modes. If more conditions apply, the string will circulate on the screen.
String
Description
LINE
Line Mode
bATT
Battery Mode
bYPA
Bypass Mode
STbY
Standby Mode (No output)
TEST
Battery Test Mode
ECO
ECO Mode (UPS offers better efficiency, but with transfer time. Double-
conversion is bypassed)
CVCF
Constant Voltage Constant Frequency. Converter Mode (Fixed output frequency.
Output power must be reduced to 60%)
SITE
Site fail (Please check input connection, for example plug can be turned to swap
Line and Neutral)
EPO
Emergency Power Off (reset EPO first)
In case of other code, please consider this as a fault. Turn off the UPS and contact service.
VII. Setting by LCD Module
In bypass or no standby mode, press “Enter” button to enter setting mode. The middle section
displays setting entry. The right section display current value of the setting. Press enter to edit
the value; the right section will start to blink. Press “select” to change the value. Press “enter”
again to confirm and save the setting.
If nothing was pressed for more than 10s, the setting mode will exit automatically.
Each button pressing must last longer than 1 second.
Setting
Entry
Description
OPV
Output Voltage Setting (220/230/240V)
Table )
6
Fault active
Beep continuously
7
Button function active
Beep once

ENGLISH
OPF
Output Frequency
bYPA
Bypass Mode (000 = disabled bypass; 001 = enabled bypass)
MOdE
UPS (normal mode), ECO (high efficiency mode), CVF (converter mode)
EbAH
External Battery Ah (Power) values 005-300 means 5-300Ah
bATT
Battery Remaining Time (000 = disabled time display; 001 = enabled)
CHG
Charging current (value in Ampere)
VIII. Technical Specification
Model No.
1000 TG(B)
1000 TGS
2000 TG(B)
2000 TGS
3000 TG(B)
3000 TGS
Input
Single Phase 176-300 VAC or 80-285 VAC in bypass mode with 40-70Hz
Output
Single Phase 220/230/240V with 50/60Hz
DC Voltage
24V
24V
48V
48V
72V
72V
Power
9Ah
5Ah~120Ah*
9Ah
5Ah~120Ah*
9Ah
5Ah~120Ah*
Model No.
VFI 1000 TG/TGB/TGS
VFI 2000 TG/TGB/TGS
VFI 3000 TG/TGB/TGS
Power rating
1kVA/0.9kW
2kVA/1.8kW
3kVA/2.7kW
Ambient Temperature
0 oC to 40 oC
Operating humidity
< 95%
Altitude
< 1000m(Note 1)
1000m< Altitude≤3000m(Note 2)
Storage temperature
-25°C~55°C
Note 1: the load no derating
Note 2: the load should derating 1 % for every up 100m