Boca Flasher HPNFC-RT User manual

Installation Manual
HPNFC-RT
WARNING: DO NOT LIFT FIXTURE BY CABLES.
Do not attempt to install or use the HPNFC-RT
fixture without reading the installation instructions
and safety labels completely.
This could result in permanent damage to both the xture and the cables. Damage resulting from grasping cables and/or putting
undue pressure on the cable connections will not be covered under the warranty!
FAILURE TO ADHERE TO THESE INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY OR PROPERTY DAMAGE.
DO NOT MODIFY, ALTER OR ATTEMPT TO SERVICE THE HPNFC-RT
DOING SO WILL VOID THE WARRANTY.

Installation Instructions
HPNFC-RT
Introduction:
The Boca HPNFC-RT is a line voltage xture that eliminates the need for secondary transformers, making installation contractor friendly. The
housing is a clear anodized aluminum with a durable nish making it weather and abrasion resistant. It is UL Listed for dry, damp or wet
location (model dependent). See layout drawings for model provided.
Maintenance:
CLEANING Dry and Damp (IP65) Rated Fixtures: To clean surface use a soft damp cloth.
Wet (IP68) Rated Fixtures: To clean surface use a soft cloth with mild soap and water.
STORAGE Store in a dry, well-ventilated area when product is not in
use. Keep the electrical cord away from heated surfaces
when in use or not in use. If cord shows signs of damage
do not use, return product to manufacturer.
Electrical Specifications:
1. Input Voltage: 90-120VAC, 230-277VAC
2. Total linear ft per 20A breaker: HO8 = 175’
Total linear ft per 20A breaker: HO6 = 200’
Total linear ft per 15A breaker: HO8 = 130’
Total linear ft per 15A breaker: HO6 = 150’
3. Input Current: HO8 = 114mA RMS per linear ft.
Input Current: HO6 = 95mA RMS per linear ft.
Indoor/Outdoor Shallow Prole Line Voltage
Model Dependent
Max temp: 55C
Min. temp: -40C
DAMP LISTING
IP65
WET LISTING
IP68
Turn Power Off At Circuit Breaker
Before Beginning Installation!
INCLUDED IN THIS PACKAGE:
Power cord length is
6.5ft per UL standard
Mounting Brackets
(2 brackets per xture)
Job Specic Drawings
123
Swivel
Fixed
OR
3" Arc
OR
6" Arc
PAGE 2 OF 8
HPNFCRT Fixtures
(In lengths shown on job specic drawings)
Fixtures must be installed by a qualied and
licensed electrician in accordance with all national,
state and local electrical codes and regulations.
If any part of this manual does not meet the
necessary codes and regulations, contact the
factory for more information before attempting
to install.
HPNFC-HO
HPNFC-RT

Installation Instructions
HPNFC-RT
CAUTION: Before installing any type of clip (xed, swivel or arc) onto the mounting surface determine if the xtures have
rigid or twist lock connections at each end (examples of the rigid and twist lock types are shown in section 4).
Installation of clips for light fixtures
with RIGID Connections
1. Light xtures that have rigid connections on each end must be installed in the same plane and must also be in a straight alignment.
Using a chalk line or laser, mark a line on the at surface where the clips are to be mounted. Align each clip to the chalk line using
the same reference point on each clip (clip edge or hole) and space the clips according to the length of each xture (see gure A).
Clip placement: Boca Flasher recommends clips to be installed 1.5” from end cap.
2. Snap in the rst light xture into the clips (see section 2, installing xtures into clips). Snap the 2nd. light xture into adjacent clips
ensuring that the connections will mate (male to female, see gure B).
3. Slide the second light xture into the rst light xture until fully seated. ( see gure B & 4d).
4. Install #2 lock screw (see gure 4e).
5. CAUTION DO NOT MATE FIXTURES THAT ARE NOT IN LINE OR FORCE TOGETHER BY WIGGLING.
THIS CAN CAUSE PERMANENT DAMAGE TO FIXTURE CONNECTION AND OPERATION. ( see gure B).
6. Continue this process until all light xtures are installed according to the job specic layout drawings.
7. Connect xtures to power per section 5 and 6.
FIGURE A: CLIP ALIGNMENT
PAGE 3 OF 8

Installation Instructions
HPNFC-RT
PAGE 4 OF 8
1. INSTALL CLIPS INTO SUBSTRATE
Place the notch on the clip
into the rst notch of the
xture.
1a
Fixed Clips
1b
1a
Swivel Clips
1b Locking Swivel Bracket:
1. Boca Flasher
recommends using an
o set Philips screw
driver with a #2 bit.
2. Screwdriver should be
capable of making
90° bend.
2a
3” Arc and 6” Arc Bracket Installation
Screw Information:
1. Screws not provided by Boca Flasher.
2. Boca Flasher recommends wide
washer at head Philips #8 screw
(not to exceed .418” in diameter).
3. Length of screw will vary depending
on mounting surface.
4. For outdoor installations, installer
should use a screw with
weatherproof coating.
1a
1b
2. INSTALL FIXTURE INTO CLIPS
Clip will securely snap
into place.
snap!
▶
▶
Fixture will pivot
on notch as
it is pushed
down.
2b If using the Swivel Clip
or Arc Bracket loosen the
screw where the clip and
swivel bracket meet to ad-
just angle of the xture.
2d
2c

FIXTURE LENGTH
FIXTURE LENGTH FIXTURE LENGTH
Installation Instructions
HPNFC-RT
PAGE 5 OF 8
3. CLIP POSITIONING
Fixed Mounting Clip
3a
4. CONNECT DMX CABLES TOGETHER AS SHOWN ON JOB SPECIFIC DRAW
Labels on xtures correspond with nomenclatures on drawings.
IMPORTANT NOTE:
Not screwing xtures together represents an incomplete install and
voids the warranty. If any xtures are damaged as a result of
improper installation. Click
▶
12
Connect Male and Female end caps in
order shown on job specic drawings.
4c
12
Push together until you hear a “Click”
then twist until secure.
4d
Swivel Mounting Clip
3b
FIXTURE LENGTH
FIXTURE LENGTH FIXTURE LENGTH
Arc Mounting Clip
3c
4a Rotate xture to see bottom and
note each label. 4b Cross-reference with Job
Specic Drawing.
HPNFC-HO
HPNFC-HO
▶
◀
▶
▶
BF-01
▶
▶
HPNFC-RT

Installation Instructions
HPNFC-RT
Installation of clips for light fixtures
with TWIST LOCK Connections
1. Light xtures that have twist lock connections on each end may be installed in areas where the surface plane may be at slightly
dierent levels between light xtures. Also, the light xtures do not have to be in straight alignment and can be laid out to dierent
angles and patterns.
2. Using a chalk line or laser mark a line on the at surface where the 2 clips for the 1st. xture are to be mounted. (See Figure: A)
3. Snap in the rst light xture into the clips (see section 2 installing xtures into clips).
4. Using a chalk line or laser mark a line on the at surface where the 2 clips for the 2nd xture are to be mounted, this xture can be
placed on a slightly dierent plane as long as the cord between the 2 xtures is long enough. Also, this xture can be placed at a
dierent angle than the rst xture (see gure 4).
5. Snap in the 2nd light xture into the clips (see section 2 installing xtures into clips).
6. Continue this process until all light xtures are installed according to the job specic layout drawings.
7. Connect xtures to power per section 5 and 6.
PAGE 6 OF 8
4. CONNECT FIXTURES TOGETHER TWIST LOCK CONNECTION
Connect Male and Female
twist lock cables in
order shown on job
specic drawings.
Push together and then twist until
completely connected and sealed
if outdoors.
4c
4b
See above for information
on determining layout.
4a
Add tape to twist locks.
Place thumb over tape at starting point and PULL
around connector area until tape overlaps itself.
Light xtures can be mounted at
various angles and levels.

Installation Instructions
HPNFC-RT
PAGE 7 OF 8
4. CONNECT FIXTURES TO POWER Recommended Install - Option 1
5. CONNECT TO A DIMMING SYSTEM
12V
CLASS-1
NEMA 4R
12V - CLASS 2 (8 outputs)
12V - CLASS-1
120/277V
12V
CLASS-1
NEMA 4R
12V - CLASS 2 (8 outputs)
12V - CLASS-1
120/277V
4. CONNECT FIXTURES TO POWER Recommended Install - Option 2
12V
CLASS-1
120/277V
NEMA 4R
12V - CLASS-1
12V - CLASS 2 (8 outputs)

Installation Instructions
HPNFC-RT
IMPORTANT SAFETY REMINDERS:
We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.
bocaflasher.com. For specific requirements, contact your Boca Flasher sales representative. Boca Flasher, Inc. 552 NW 77th Street Boca Raton,
Florida 33487 USA Phone: [phone] Fax: [phone] © 2015 Boca Flasher, Inc. All rights reserved. All names and trademarks are property
of their respective owners. REV 07-2017
DAMP LISTING
IP65
WET LISTING
IP68
1. DANGER:
To reduce the risk electric shock, always unplug the HPNFC-RT from electrical outlet before cleaning. Cut breaker
if outlet is not available.
2. To reduce the risk of burns, re, electric shock or injury to persons:
• Use the HPNFC-RT only for its intended use as described in these instructions.
• Do not use attachments not recommended by Boca Flasher.
• Never operate the HPNFC-RT if it has a damaged cord, cable or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. If the seal appears to be damaged/broken/torn return the xture
to a service center for examination or repair.
• Keep cables away from heated surfaces
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
3. WARNING:
Do not attempt to install or use the HPNFC-RT without reading the installation instructions and safety labels.
Failure to adhere to these instructions could result in serious injury or property damage.
4. Do not modify, alter or attempt to service the HPNFC-RT:
Doing so will void the warranty.
5. There are no serviceable parts within the HPNFC-RT:
Please contact your local representative if issues arise on site during or after installation.
6. Do not use sharp tools near or on the xture lens:
Doing so will result in property damage and void the warranty.
Boca Flasher, Inc.
508 S. Military Trail nDeerfield Beach, Florida n33442 USA
Phone: [phone] nFax: 561-982-8323
www.bocaflasher.com
7. REMOVING FIXTURES FROM CLIPS IF NECESSARY
Slide a at head screwdriver in
between the clip and xture.
7a While holding the xture with your
other hand, pull back on screwdriver
to release from notch.
7b Once released from one notch,
xture can be fully removed.
7c