Boca Flasher INGRADE User manual

Installation Manual
INGRADE
BocaFlasher.com 1 of 4 REV 04-2019
INTRODUCTION:
The Boca InGrade is an ingrade lighting xture assembly designed to provide lighting in ground-recessed applications.
Our IP68 rated HPNLS line voltage xture rests inside an aluminum housing, protected by a glass lens rated for up
to Class 2 vehicles (10,000 lbs).
WARNING: DO NOT LIFT FIXTURE BY CABLES. Do not attempt to install or use the INGRADE xture without
reading the installation instructions and safety labels completely.
This could result in permanent damage to both the xture and the cables. Damage resulting from grasping cables and/or
putting undue pressure on the cable connections will not be covered under the warranty!
FAILURE TO ADHERE TO THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE.
DO NOT MODIFY, ALTER OR ATTEMPT TO SERVICE THE INGRADE DOING SO WILL VOID THE WARRANTY.
Max Temp: 55°C
Min. Temp: -40°C
IP66
Wet Listing
TURN POWER OFF AT CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION!
INCLUDED IN THE PACKAGE:
2. IG-HPNLS Housing 3. IG-HPNLS Glass Lens1. HPNLS Light xture (In lengths shown on
job specic drawings)

BocaFlasher.com 2 of 4
Installation Manual
INGRADE
REV 04-2019
INSTALLATION CHECKLIST:
1. Prepare the ground to support IG-HPNLS housing.
2. Verify the drainage ef ciency of site including the ground material and drainage piping.
3. Inspect the housing and lighting xtures for damage or nonconformities.
4. Verify the housing is level.
5. Insure the lighting xture is securely mounted onto the mounting clips inside the housing.
6. Insure the glass lens cover is properly installed.
7. Fill in ground hole.
8. Make nal inspection, insuring glass is level.
KNOCKOUT FOR ELECTRICAL CABLE 2x Knockout holes (1” OD) for conduit
INSTALLATION STEPS
Length Minimum Drainage Rate
1ft 0.064 gal/min
2 ft 0.119 gal/min
4 ft 0.231 gal/min
Installation location should provide the minimum amount of drainage
as described in the table.
1. Prepare The Ground
• Determine whether the drainage piping and material provide adequate
drainage as described in the table.
• Determine the type of materials in the hole the housing will be installed in. If concrete, or other hard ground, ensure that proper drainage
piping and electrical conduits are present. Soft ground, such as Type I or Type II soil, must also provide adequate drainage.
»Soft ground must provide adequate support for the housing’s base anges to be mounted.
2. Prepare HPNLS Lighting Fixture inside Housing
• The housing includes 2x Mounting Clips secured to brackets. The HPNLS lighting xture is to be snapped into these clips, with the electrical
cable facing the location of the conduit.

BocaFlasher.com 3 of 4
Installation Manual
INGRADE
REV 04-2019
3. Install Conduits and Electrical Cables
• Remove knockout covers as needed to install conduit and electrical cables.
• Knockout hole diameter is 1”. Installation should use conduit (exible or rigid pipe) appropriate to location and application.
• Connect conduit to housing with conduit couplers.
• Refer to HPNLS guide provided for job specic electrical connection instructions.
• Provide power and test connections.
4. Housing Placement and Alignment
• Pour concrete or other lling material around the housing. Filling material should be ush with the top of the housing.
»Be sure to remove any concrete or other lling material from the exposed top surfaces as it interferes with the installation of the glass lens.
• Lay housing at on to hole oor and ensure the housing is level.
»The InGrade Glass Lens may be installed at this point to aid in leveling. Refer to step 7.
• Make any adjustments to hole oor to level the top surface.
»Base anges must remain fully supported by any adjustments to oor to maintain structural integrity;
i.e. no gaps shall be present between ange and oor.
5. Filling the Ground
• With housing and connections in place, secure the housing
anges in the ground with application appropriate fasteners
or anchors. 1/4” diameter anchors are recommended.
• Pour concrete or other lling material around the housing.
Filling material should be ush with the top of the housing.
»Be sure to remove any concrete or other lling material
from the exposed top surfaces as it interferes with the
installation of the glass lens.

BocaFlasher.com 4 of 4
Installation Manual
INGRADE
REV 04-2019
6. Lens Installation
• With the lling material set, place the
glass lens cover over the housing and
press down until the security clips click.
1. DANGER:
To reduce the risk electric shock, always unplug the INGRADE from electrical outlet before cleaning.
Cut breaker if outlet is not available.
2. To reduce the risk of burns, re, electric shock or injury to persons:
– Use the INGRADE only for its intended use as described in these instructions.
– Do not use attachments not recommended by Boca Flasher.
– Never operate the INGRADE if it has a damaged cord, cable or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. If the seal appears to be damaged/broken/torn return the xture to a service center for
examination or repair.
– Keep cables away from heated surfaces
– Never drop or insert any object into any opening.
– Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
3. WARNING:
– Do not attempt to install or use the INGRADE without reading the installation instructions and safety labels.
– Failure to adhere to these instructions could result in serious injury or property damage.
4. Do not modify, alter or attempt to service the INGRADE:
– Doing so will void the warranty.
5. There are no serviceable parts within the INGRADE:
– Please contact your local representative if issues arise on site during or after installation.
6. Do not use sharp tools near or on the xture lens:
– Doing so will result in property damage and void the warranty.
Boca Flasher, Inc. 508 South Military Trail, Deereld Beach, Florida 33442 USA Phone: [phone] Fax: [phone] © 2017 Boca Flasher, Inc
We are constantly improving our xtures and reserve the right to change options and specications. Additional information & details at www.bocaasher.com. For
specic requirements, contact your Boca Flasher sales representative. All rights reserved. All names and trademarks are property of their respective owners.