Bode Eurodispenser 1 plus User manual

5
BODE Eurodispenser 1 plus
Properties

Robust, autoclavable metal dispenser for the hygienic
application of hand disinfection, cleansing and care
products. Easy pump exchange through removal from
the front. BODE Eurodispenser 1 plus is a user-friendly
dosing dispenser, that can be utilised flexibly. Advantages
at a glance:
all removable parts completely autoclavable
easy installation even with limited space
all standard bottles insertable
dosing amount adjustable to approx. 0.75 to 1.5 ml per
actuation
delivery incl. mounting parts, instruction sheet and
manual
Set-up
Open cover with panel, control lever and outlet screen
Wall plate with three drilled holes (identical to
Eurodispenser 1)
Pump
Technical data
Dispenser for 350/500 ml 1000 ml
Depth incl. short arm lever 160 mm 160 mm
Height 315 mm 360 mm
Width 82 mm 90 mm
Dispenser for 350/500 ml 1000 ml
Depth incl. long arm lever 215 mm 220 mm
Height 295 mm 340 mm
Width 82 mm 90 mm
Material
Cover made of matt silver, anodised aluminum;
corrosion-resistant and shock-proof
Panel, control lever and liquid pump made of stainless
V2A+-steel
Rear panel made of PA (Polyamide) and outlet screen
made of POM (Polyoxymethylene) plastics with good
alcohol and tension resistance
All materials were tested for food conformity
Dosing
The dispenser is adjusted to the maximum dosing
amount of approx. 1.5 ml/actuation. If required, the
dosing amount can be reduced stepwise to approx. 0.75 ml/
actuation by turning the dosing piece.

6
BODE Eurodispenser 1 plus
Mounting instructions
Preparation of the mounting location
When selecting the mounting location, the following
points have to be considered:
irrespective of dispenser type, provide for a space of
approx. 50 mm (necessary for dismounting the
dispenser)
keep a minimum distance between dispenser and top
edge of wash basin or work space (for trouble-free
bottle exchange)
the wall should be clean, dry and even
mind the bearing capacity: besides weight of
dispenser, pump and product bottle, the load of arm
lever actuation has to be considered. Therefore,
please only use the provided mounting material for
attaching the Eurodispenser to the wall
make sure that no electric cables, gas mains or other
utility cables and pipes are damaged by drilling
Warning: the BODE Eurodispenser 1 plus cannot be
attached to the wall with Powerstrips. For secure
mounting use the provided mounting material.
Mounting
For mounting you need a drilling machine, a 6 mm drill
(type depends on wall material), and a screwdriver or a
cordless screwdriver. All other mounting material (wall
anchors, screws, shims) is included in delivery. Data on
dispenser dimensions, necessary minimum distance to
washbasin/work space, etc. you will find in the
aforementioned detail drawings.
Mark drill holes on the wall, carry out drilling and put wall
anchors in. Take dispenser out of the cardboard box:
1. Press locking tongue and pull wall holder off the
housing
2. Mount backplate with wall anchors and screws at the
designated location
3. Slide dispenser on the backplate (top down) until the
locking tongue snaps in
4. Put bottle in dispenser (bottom-up)
5. For activation press arm lever several times, so that
the dip tube sucks in the product. In doing so, hold
your hand under the outlet

7
BODE Eurodispenser 1 plus
Long arm lever
(350/500 ml)
Long arm lever
(1000 ml)
Pump exchange
Slightly pull and then turn the outlet cover upwards. Keep
pump lock pressed and pull pump out.
Reprocessing
Cleaning and disinfection of the dispenser body and
dosing pump should be carried out each time the bottle
is exchanged.
Manual reprocessing of the dispenser
take bottle out of dispenser
take dosing pump out
push cap up by pressing the locking tongue
rinse cover thoroughly under hot running water until no
product residuals are visible anymore
clean rear, screwed on dispenser part with moistened
disposable tissue
spray both dispenser parts with an alcohol-based
surface disinfectant and wipe them with disposable
tissues if required; pay attention to application time
slide on cover
put in new or separately reprocessed dosing pump
(see below)
hook in new bottle and pump product through
Manual reprocessing of the pump
First of all, rinse pump thoroughly with hot water and
cleanse it of product residuals
Rinse pump thoroughly with alcohol-based surface
disinfectant and leave it for 5 minutes
Afterwards pump it dry
After complete drying, insert pump again or store it in
dust-free area
Note: Do not use abrasives or corrosive cleaners
Sterilisation
For routine usage and compliance with the hygiene
standards, manual cleaning and disinfection of dispenser and
dosing pump (like described above) suffice. In areas, where
hygiene is of particular importance, a higher hygiene standard
may be necessary. In these cases all removable parts of
the BODE Eurodispenser 1 plus can be autoclaved with
superheated steam (121°C, 1 bar).
Arm lever lengths
160
70
215
50
225
50

8
BODE Eurodispenser 1 plus
Steel
replacement
pump
Drop catcher
Drop catcher with
separate wall fixation
Bed frame fixation
Mounting angle
Locking device
Back board
Counter
Accessories
Accessories for 350 / 500 ml metal dispenser
Sales unit Art. No.
Locking device 1 pc 975577
Steel replacement pump 1 pc 975575
Back board 1 pc 826420
Mounting angle 1 pc 974870
Drop catcher 1 pc 974750
Drop catcher
with separate wall fixation 1 pc 974762
Bed frame fixation 1 pc 974613
Accessories for 1000 ml metal dispenser
Sales unit Art. No.
Locking device 1 pc 975578
Steel replacement pump 1 pc 975576
Back board 1 pc 826440
Mounting angle 1 pc 974880
Drop catcher 1 pc 974760
Drop catcher
with separate wall fixation 1 pc 974762
Bed frame fixation 1 pc 974614
BODE Eurodispenser 1 plus
Available size Sales unit Art. No.
for 350 / 500 ml bottles
with short arm lever (total depth 160 mm) 1 pc 981098
with long arm lever (total depth 215 mm) 1 pc 975570
for 1000 ml bottles
with short arm lever (total depth 160 mm) 1 pc 981099
with long arm lever (total depth 220 mm) 1 pc 975572
Counter
The integrated counter function reliably measures the
number of times the dispensers is used.
The counter function can help collect data about hand
hygiene practices in hospitals at regular intervals, which
in turn can be registered and evaluated. The results
make it possible to gain an insight into the daily hand
hygiene practices in a hospital or in wards. With this
counter function e.g. wards can be compared with each
other.
Available size Sales unit Art. No.
for 350 / 500 ml bottles
with long arm lever (total depth 215 mm) 1 pc 981124
for 1000 ml bottles
with long arm lever (total depth 220 mm) 1 pc 981125