Body Flex Sports Body Power BST800 StepTrac User manual

BST800
STEPTRAC™ ELLIPTICAL STEPPER
WORKOUT TRAINER WITH
CURVE-CRANK®TECHNOLOGY
OWNER’S MANUAL
This product is intended for indoor, home use only and is not to be used in a commercial setting.

This page is left blank intentionally

BST800 Page 1
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE USE & REFERENCE.
DO NOT DISCARD.
WARNING: SERIOUS INJURIES AND EVEN DEATH CAN OCCUR IF THE PROPER SAFETY PRECAUTIONS
ARE NOT FOLLOWED.
The diagram below highlights and reviews many of the important Safety and Warning labels also found on the unit.
Please ensure any user of the unit familiarizes themselves with this Safety and Warning guidelines before use.

BST800 Page 2
Before you undertake any exercise program, please be sure to
consult with your doctor.
Frequent strenuous exercise should be approved by your
doctor and proper use of your product is essential.
Excessive or incorrect training may result in health injuries.
Please read this manual carefully before commencing the
assembly of your product or starting to exercise.
• Please keep all children away from this item when in use.
Do not allow children to climb or play on this item when it
is not in use.
• Supervise teenagers while they use this unit.
• For your own safety, always ensure that there are at least
3 feet of free space in all directions around your product
while you are exercising.
• Regularly check to see that all nuts, bolts and ttings are
securely tightened. Periodically check all moving parts for
obvious signs of wear or damage.
• Any adjustment devices that could interfere with the user’s
movement of this unit should not be left projecting.
• Clean only with a damp cloth, do not use solvent
cleaners. Lubricate the moving parts of your unit every 30
days with a silicone-based grease or product.
If you are in any doubt, do not use your product; contact
CUSTOMER SUPPORT.
• Before use, always ensure that your product is positioned
on a solid, hard-at surface.
• Do not place on carpet. If necessary, use a rubber mat
underneath to reduce the possibility of slipping.
• Always wear appropriate clothing and footwear such as
training shoes when exercising. Do not wear loose clothing
that could become caught in moving parts during exercise.
• Do not use this unit if it is not functioning properly or if it is
not fully assembled.
• Do not use this unit for commercial purposes. This unit is
for home use only.
• Before use, you must read and understand all instructions
& warnings stated in this Owner’s Manual as well as
posted on the equipment.
• It is the facility owner’s responsibility to properly instruct
users on the proper operation of the equipment and to
warn them of the potential hazards.
• If at any time during exercise you feel faint, dizzy or
experience pain, stop and consult your physician.
Your product is intended for use in clean dry conditions. You
should avoid storage in excessively cold or damp places as
this may lead to corrosion and other related problems.
If you have any questions concerning the assembly of your
item or if any parts are missing, please DO NOT RETURN
THE ITEM TO THE STORE OR CONTACT THE
RETAILER.
Our dedicated customer service sta󰀨 can help you with
any questions you may have regarding the assembly of this
unit and can also mail you replacement parts.
Customer Support is open 9:00 a.m. to 5:00 p.m. (Pacic
Time) Monday through Friday.
Please contact us by any of the following means :
Body Flex Sports, Inc.
21717 Ferrero Parkway, Walnut, CA 91789
Telephone: [phone] - 6789
Fax: [phone] - 6707
Email: info@bodyexsports.com
Body Flex Sport warrants your product is free of any defects in
workmanship and materials for a period of 1 year for the frame
and 90 days on all parts if the item is used for the
intended purpose, properly maintained and not used
commercially.
Any alterations or incorrect assembly of the product will void
this warranty.
Proof of purchase must be presented for any warranty
validation (no exceptions). This warranty applies to the original
purchaser only and is not transferable.
This warranty covers parts damaged due to defect in work-
manship and materials; it does not cover abuse or damages
caused during use, storage or assembly. During the warranty
period, Body Flex Sport reserves the right to:
1. provide replacement parts to the purchaser in an e󰀨ort to
repair the item.
2. repair the product returned to our warehouse
(at purchaser’s cost).
3. replace the product if neither of the two previously
- Ruler with both Metric and English measurements
- 2 x Adjustable Wrenches
- 1 x Philips (”Crosshead”) Screw Driver
Your product is suitable for users weighing:
250 pounds or less
General Information
Safety Storage and Use
Questions
Customer Support
Warranty
Assembling Tools
Weight Limit

BST800 Page 3
Before Assembly
1. Take a few minutes to familiarize yourself with the parts and hardware included with your product.
2. The assembly may require two people.
3. Check the frame for any damage and check any wiring (if present) for rips or tears. If you detect damage, rips, or
tears, please contact our Customer Support Team before beginning any assembly.
4. Make sure all the hardware needed is included.
5. It is very important to follow the assembly instructions correctly and to make sure all parts are attached correctly and
rmly tightened when the assembly process is complete.
6. Parts that are not tightened correctly will seem loose and can cause irritating noises and will cause damage to the
equipment.
Tools Required For Assembly
WARNING
PLEASE NOTE : Many of the parts and hardwares listed on the parts list are already pre-assembled or
installed on the unit.
Tool Description/Purpose
Ruler (with both Metric and English measurements)
QTY: 1
Use to measure the length or size of hardware including
bolts to ensure you are using the correct part.
Adjustable or at wrenches
QTY: 2
Use to securely install parts including nuts and bolts.

BST800 Page 4
Part Listing
The following parts list describes all of the parts illustrated in the exploded diagram on the following page.
PLEASE NOTE: most of these parts are already pre-assembled on your unit.
# Description
01 Main Frame
02 Front Post
03 Left Coupler Bar
04 Right Coupler Bar
05 Left Pedal Tube
06 Right Pedal Tube
07 Left Slide Rail
08 Right Slide Rail
09 Magnet Base
10 Magnet Bracket
11 Front Handle Bar
12 Left Handle Bar
13 Right Handle Bar
14 Connection Joint
15 Rear Stabilizer
16 Front Stabilizer
17 Left Shroud 1
18 Right Shroud 1
19 Left Shroud 2
20 Right Shroud 2
21 Left Pedal
22 Right Pedal
23 Pulley
24 Wheel
25 Bumper
26 End Cap
27 Left End Cap for Front Stabilizer
28 Right End Cap for Front Stabilizer
29 Left End Cap for Rear Stabilizer
30 Right End Cap for Rear Stabilizer
31 Bushing
32 Pedal Shroud
33 Foam Grip
34 Belt Wheel
35 Belt
36 Foam Grip
37 End Cap
38 Magnet Box
39 Tension Controller Cover
40 Bushing
41 End Cap
42 Bushing
43 Crank Cover
44 Left Fly Wheel Cover
45 Right Fly Wheel Cover
46 Crank Cover
47 Monitor
48 Sensor
49 Magnet
51 Tension Controller
52 Magnet
53 Fly Wheel Axle
54 Handle Bar Axle
55 Left Pedal Hinge Bolt
56 Right Pedal Hinge Bolt
57 Crank Axle
# Description
58 Left Crank
59 Right Crank
60 Fly Wheel
61 Bearing (6004zz)
62 Bearing (6000zz)
63 Bearing (6200z)
64 Bolt (M6x55 mm)
65 Spring
66 Tool (S13-17-19)
67 Tool (S5)
68 Tool (S6)
69 Tool (S8)
70 Pop-Pin (M8x50 mm)
71 Tool (S13-14-15)
72 Nylon Nut (M8)
73 Nut (M10)
74 Nylon Nut (M10)
75 Flange Nut (M10x1 mm)
76 Flange Nut (M10x1.25 mm)
77 Screw (M5x8 mm)
78 Bolt (M8x20 mm)
79 Bolt (φ10x11xM8x12 mm)
80 Bolt (φ10x11xM8x15 mm)
81 Hex Bolt (M8x50 mm)
82 Bolt (M8x55 mm)
83 Bolt (M10x50 mm)
84 Carriage Bolt (M8x40 mm)
85 Nut (M8)
86 Screw (M5x15 mm)
87 Bolt (M8x70 mm)
88 Arc Washer (M8)
89 Bolt (M6x12 mm)
90 Screw (ST4.2x13 mm)
91 Screw (ST4.8x19 mm)
92 Screw (ST4.2x12 mm)
93 Screw (ST2.9x12 mm)
94 Left Nylon Nut (1/2")
95 Right Nylon Nut (1/2")
96 Spring Washer (1/2")
97 Spring Washer (M8)
98 Washer (M8)
99 Bolt (M8x50 mm)
100 Bolt (φ10x30xM8x12 mm)
101 D Shape Washer (1/2")
102 Wave Washer (1/2")
103 Washer (M8)
104 Bolt (M8x40 mm)
105 Bolt (M8x25 mm)
106 Bolt (M8x42 mm)
107 Bolt (M6x40 mm)
108 Nut (M6)
109 Nut (M6)
110 C Clip
111 Screw (ST4.2x15 mm)
112 Bolt (M8x45 mm)
113 Linkage
114 Wire Plug
50 Hand Pulse
115 Bolt Cap
116 End Cap

BST800 Page 5
Exploded View
The following diagram is provided to help you familiarize yourself with the parts and hardware that will be used during the
assembly process.
: : Not all of the parts and hardware you see here will be used while you are assembling the machine
because some of these items are already pre-installed. Please use this page only as a reference guide for parts and
hardware.
PLEASE NOTE

BST800 Page 6
Hardware and Tool List
The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these items.
PLEASE NOTE: Most of these parts are already pre-assembled on your unit. Do not be alarmed if you see parts on this
page that are not included in your hardware packet.
#78 Bolt (M8x20 mm)
6 pcs
#104 Bolt (M8x40 mm)
1 pc
#102 Wave Washer (1/2")
4 pcs
#101 D Shape Washer (1/2")
2 pcs
#66 Tool (S13-17-19)
1 pc
#68 Tool (S6) 1 pc
#69 Tool (S8) 1 pc
#67 Tool (S5)
2 pcs
#71 Tool (S13-14-15)
1 pc
2 pcs
#88 Arc Washer (M8)
12 pcs
#97 Spring Washer (M8)
11 pcs
#105 Bolt (M8x25 mm)
2 pcs
#106 Bolt (M8x42 mm)
4 pcs
#112 Bolt (M8x45 mm)
8 pcs
#111 Screw (ST4.2x15 mm)
2 pcs
#77 Screw (M5x8 mm)
4 pcs
pre-assembled
#72 Nylon Nut (M8)
12 pcs
#24 Wheel
2 pcs
#70 Pop-pin (M8x50 mm)
1 pc
#79 Bolt (φ10x11xM8x12 mm)
2 pcs
#100 Bolt (φ10x30xM8x12 mm)
2 pcs
#80 Bolt (φ10x11xM8x15 mm)
2 pcs
#81 Hex Bolt (M8x50 mm)
4 pcs
#84 Carriage Bolt (M8x40 mm) 4pcs
#85 Nut (M8) 4 pcs
#55 Left Pedal Hinge Bolt 1 pc
#56 Right Pedal Hinge Bolt 1 pc
#94 Left Nylon Nut (1/2") 1 pc
#95 Right Nylon Nut (1/2") 1 pc
#96 Spring Washer (1/2") 2 pcs
#115 Bolt Cap
2 pcs
#98 Washer (M8)
9 pcs
#103 Washer (M8)

BST800 Page 7
Assembly STEP 1
With the help of an assistant, attach the Front Stabilizer (#16)
to the front of the Main Frame (#01). Secure with four Bolts
(#78), four Spring Washers (97) and four Washers (#98).
Attach the Rear Stabilizer (#15) to the rear of the Main Frame
(#01). secure with four Bolts (#112), four Spring Washers (97)
and four Washers (#98) .
Attach the Front Post (#02) to the Main Frame (#01), secure
with one Bolt (#104), one Spring Washer (97), one Washer
(#98) from the rear and two Screws (#111) from each side.
Attach the Left Slide Rail (#07) to the Main Frame (#01).
Secure with two Bolts (#106), two Arc Washers (#88), two
Nylon Nuts (#72) from the front. And two Bolts (#112),
two
Repeat the above the process on the right side of the machine.
Arc Washers (#88), two Nylon Nuts (#72) from the rear.
NOTE BEFORE STARTING THE ASSEMBLY PROCESS :
To avoid misalignment due to over-tightening, please do not use a wrench and use only hand-tightening for now to ensure
easy assembly. Wrench-tightening should be performed after all parts are assembled to ensure all nuts, bolts, and parts are tightly se
cured before use.
#78 Bolt (M8x20 mm)
#97 Spring Washer (M8)
9 pcs 9 pcs
#104 Bolt (M8x40 mm)
1 pc
#88 Arc Washer (M8)
8 pcs
#106 Bolt (M8x42 mm)
4 pcs
#112 Bolt (M8x45 mm)
8 pcs
#72 nut M8
8 pcs
#111 Screw (ST4.2x15 mm)
2 pcs
#98 Washer (M8)
Hardware RequiredHardware RequiredHardware Required
4 pcs

BST800 Page 8
Hardware Required
2 pcs
Hardware Required
#55 Left Pedal Hinge Bolt 1 pc
#56 Right Pedal Hinge Bolt 1 pc
#94 Left Nylon Nut (1/2") 1 pc
#95 Right Nylon Nut (1/2") 1 pc
#96 Spring Washer (1/2") 2 pcs
#72 Nylon Nut (M8)
4 pcs
#81 Hex Bolt (M8x50 mm)
4 pcs #24 Wheel
#100 Bolt (φ10x30xM8x12 mm)
2 pcs
#102 Wave Washer (1/2")
2 pcs
#115 Bolt Cap
2 pcs
Secure the Left Pedal Hinge Bolt (#55) tightly into the Left
Crank (#58) by turning CLOCKWISE.
Then, secure with a Spring Washer (#96) and a
Left Nylon Nut (#94)
Align and attach the Left Pedal Tube (#05) to the Left Crank
(#58). Insert the Left Pedal Hinge Bolt (#55) through
a Wave Washer (#102) , Left Pedal Tube (#05) and
Left Crank (#58).
Attach Left Pedal (#21) to the Left Pedal Tube (#05), secure
with two Hex Bolts (#81) and two Nylon Nuts (#72).
Repeat the above process on the right side of the machine.
Attach the Wheel (#24) to the Left Pedal Tube (#05), secure
with one Bolt (#100).
Repeat the above process on the right side of the machine.
by turning COUNTER-CLOCKWISE .
Attach Bolt Cap (#115) to the Left Carnk (#58).
Assembly STEP 2

BST800 Page 9
Assembly STEP 3
Hardware Required
#78 Bolt (M8x20 mm)
2 pcs
#102 Wave Washer (1/2")
2 pcs #101 D Shape Washer (1/2")
2 pcs
2 pcs
#97 Spring Washer (M8)
2 pcs
#79 Bolt (φ10x11xM8x12 mm)
2 pcs #80 Bolt (φ10x11xM8x15 mm)
2 pcs
#103 Washer (M8)
Insert the Handlebar Axle (#54) through the Main Frame
(#01). Make sure the Handlebar Axle (#54) is centered. If you
encounter too much friction, try using WD40 or Vaseline as a
lubricant.
Attach two Wavy Washers (#102),Left Coupler Bar (#03)
and Right Coupler Bar(#04) to the Main Frame (#01) via the
Handlebar Axle (#54). Again, use WD40 or Vaseline to reduce
friction if needed.
Once the Left Coupler Bar (#03) and Right Coupler Bar (#04)
are correctly situated, fasten the end of the Handlebar Axle
(#54) with a D Shape Washer (#101), a Washer (#103), a
Spring Washer (#97) and a Bolt (#78) on each side.
Attach Connection Joint (#14) to the Left Couple Bar (#03),
Secure with one Bolt (#80).
Attach Connection Joint (#14) to the Left Pedal Tube (#05),
Secure with one Bolt (#79).
Repeat the above process on the right side of the machine.
3
5

BST800 Page 10
Assembly STEP 4
Attach Left Handle Bar (#12) to the Left Coupler Bar (#03),
secure with two Carriage Bolts (#84) two Arc Washers (#88)
and two Nuts (#85).
Repeat the above process on the right side of the machine.
Attach the Front Handle Bar (#11) to the Front Post (#02),
secure with two Bolts (#105).
Hardware Required
#88 Arc Washer (M8)
4 pcs
#105 Bolt (M8x25 mm)
2 pcs
#84 Carriage Bolt (M8x40 mm) 4 pcs
#85 Nut (M8) 4 pcs

BST800 Page 11
Assembly STEP 5
Attach the Monitor (#47) to the bracket on the Front Post (#02),
secure with four Screws (#77).
Connect the Wire A to the Wire B as illustration on the right.
Hardware Required
#77 Screw (M5x8 mm)
4 pcs
pre-assembled
#70 Pop-Pin (M8x50 mm)
1 pc
Remove the four Screws (#77) that are pre-assembled on the back
of the Monitor (47), set them aside nearby.
After using, please insert the Pop-Pin (#70) to the holes on the left
Connection Joint (#14) and Left Slide Rail (#07).
THE ASSEMBLY PROCESS IS NOW COMPLETE.
However, for your own safety, please make sure to read this
entire Owner’s Manual which includes safety instructions and
warnings, as well as any safety/warning labels a󰀩xed to the
product before use.

BST800 Page 12
Computer Operation
MODE :
Press this button to select the display function of your
choice.
RESET :
Hold MODE button for 3 seconds to reset all value to
zero.
UP DOWN :
Press UP DOWN to set workout level
Key Function
*IMPORTANT NOTE :
Please remember that the functions in this computer are only meant to be tools to
monitor your workout progress; they are not meant to provide medical information
or be used for medical purposes. Please consult a physician before beginning any
workout program.
SCAN : The monitor will then rotate displaying through the following functions: time,speed,distance,
calories and odometer. Each function will display for 5 seconds.
TIME : Displays the total amount of time using the machine.
SPEED : Displays current speed.
DISTANCE : Displays the distance traveled.
CALORIES : Displays the amount of calories burned.
ODOMETER : Displays total accumulated distance.
PULSE : Hold the pulse sensor 6-7seconds and read your heart rate per minute.
1. If the display is faint or shows no gures ,please replace the batteries.
2. The monitor will automatically shut o󰀨 if there is no signal received after 4 minutes .
3. The monitor will auto-power on when exercise and/or motion input is detected.
4. The monitor will automatically start calculating when you start to exercise and will stop calculating when you stop
exercising for 4 minutes .
FUNCTIONS
NOTE
Operation Procedures
Specications
AUTO SCAN Every 6 seconds
TIME 00:00-99:59 min
SPEED Max 999.9 mi./H
CALORIES 0.0-999.9 KCal
ODOMETER 0.0-9999 mi.
DISTANCE 0.0-999.9 mi.
BATTERY TYPE 2 pcs of AAA
PULSE RATE 40-240 bpm
OPERATING TEMP 32°F - 104°F
STORAGE TEMP 14°F - 140°F
FUNCTIONS

BST800 Page 13
Computer Operation
NOTES (Regarding the Computer Monitor):
Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Caution:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o󰀨 and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
How To Install and Replace Batteries
1. Open the battery door on the back of the computer.
2. The computer operates on two AAA batteries (included).
Refer to the illustration to install or replace the batteries.
NOTE :
1. Do not mix a new battery with an old battery.
2. Use the same type of battery. Do not mix an alkaline
battery with another type of battery.
3. Rechargeable batteries are not recommended.
4. Battery disposal should be handled according to all state
and federal laws and regulations.
5. Do not dispose of batteries in re.

BST800 Page 14
Safety and Maintenance
• Make sure all nuts, bolts, and screws are tightened prior to use.
• Be sure that all adjustment locking devices and safety devices are properly engaged prior to use!
• Never over-tighten the above-mentioned devices and parts to avoid damage to the unit.
• Check for loose parts and components and make proper adjustments prior to use.
• Check to see if there are any tears or bends in the welding or metal prior to use. If tears or bends are found,
DO NOT use the unit and contact our CUSTOMER SUPPORT.
• Extreme care must be taken to not allow your feet, ngers, hair, clothing, and/or any loose items to be snagged into
any portion of the bike when the unit is in motion. Failure to follow these instructions could result in serious injury,
including the loss of ngers.
• Always wait for the pedals and other moving parts (which can gain great momentum during riding) to come to a
complete stop before dismounting the unit to avoid serious injury.
• Please review all safety instructions and warnings in this entire Owner’s Manual, as well as any safety/warning labels
a󰀩xed to the product before use.
• To avoid rust or corrosion to the ywheel caused by moisture and sweat, we advise wiping and drying the ywheel
and surrounding parts with a dry absorbent towel after each workout session.
• Do not use solvent cleaners. If you are in any doubt, do not use your cleansing product and contact CUSTOMER
SUPPORT.
• For any replacement warning labels, please contact our CUSTOMER SUPPORT at
1 [phone] or 1 [phone], or mail in a written request to:
Body Flex Sports, Inc.
21717 Ferrero Parkway
Walnut, CA 91789
More detailed information about how to reach our CUSTOMER SUPPORT may be found on Page 2 of the
Owner’s Manual under the “CUSTOMER SUPPORT” section.
Safety & Warning
Maintenance & Care

BST800 Page 15
Warm-Up Instructions
1. Sit with your knees exed and
soles of feet together.
2. Hold your ankles and bend
at your hips (keep your back
straight) as you press your
knees toward the oor with your
elbows.
1. Lie on your back and raise
your right leg as you clasp both
hands under the back of the
knee. Keep your left leg straight.
2. Gently pull your right leg toward
your trunk without
raising your upper body. Switch
leg positions and repeat.
1. Sit with your left leg extended
and bend your right leg at the
knee as you place the sole of
your right foot against the inner
thigh of your extended leg.
2. Flex the foot of your extended
leg (toes pointed toward
ceiling) and gently bend forward
from your hips; keep your back
straight.
3. Reach your hands on your
extended leg as far as possible
and then switch legs and repeat.
1. Assume the depicted position on your hands and knees. Stretch your
hands out in front of you and then slowly start to pull them back in toward
your body as you tuck your chin and arch your back upward.
2. Return to the starting position slowly.
1. Sit with your leg extended and
bend your right knee as you
cross your right leg over your
left leg. Your right foot of your
extended leg foot should be at
on the oor alongside your left
knee.
2. Place your left arm on the
outside of your right leg and pull
against that leg while twisting
your trunk as far as possible to
the right. Place your right hand
on the oor behind your but-
tocks. Reverse leg positions and
repeat.
Before use, you must read and understand all instructions & warnings stated in this Owner’s Manual as well as posted
on the equipment. Before beginning any exercise program including the following exibility exercises, please consult with
your physician.
The following exibility exercises are provided to you as a means to prevent injury while you are exercising. A proper
warm-up routine decreases the chance of injuring your muscles while you are exercising. Please take the time to do these
exibility exercises before and after each time you exercise.
Groin Stretch
Groin Stretch
Hamstring Stretch
Trunk Flexion, Prone
Trunk Twister

BST800 Page 16
Warm-Up Instructions
1. Bring your right hand over your
right shoulder to the
upper back and bring your left
hand under your left shoulder to
the upper back.
2. Try to reach your ngertips. If
you are not able to reach your
ngertips, use a towel as an
extension of your hands and
gently pull one hand toward the
other.
Reverse arm positions and
1. Stand on your left leg and hold
onto a support with your left
hand.
2. Flex your right leg behind you,
grasp your ankle or foot with
your right hand and pull your
foot toward your buttocks. Keep
your back straight and right
knee pointed down.
Repeat on the other leg.
1. Place both hands against a wall
to aid your balance. Press the
ball of your left foot against the
wall and keep the heel of the
same foot rested on the oor
(make sure your left knee is
bent).
2. Slowly start to straighten your
left knee and you will feel the
muscles in your left calf stretch.
Switch leg positions and repeat.
Shoulder Stretch Quadriceps Stretch Calf Twister

This page is left blank intentionally

THANK YOU FOR YOUR PURCHASE
MODEL NO.: BST800
Please ll in the information below and keep this manual
along with your sales receipt as proof of purchase.
Serial Number :
Date of Purchase :
Retailer :
Body Flex Sports, Inc.
21717 Ferrero Parkway
Walnut, CA 91789
Phone: [phone]
Fax : [phone]
Email : info@bodyexsports.com
Ver. 07/30/2019 Printed in China