Bogen NQ-PA120 Instruction sheet

Public Address Mixer/Amplifiers
Configuration Manual
NQ-PA120, NQ-PA240, NQ-PA600
2019 Bogen Communications, Inc.
All rights reserved.
740-00122A
191028

i
Contents
List of Figures ........................................................................................................ iii
List of Tables .......................................................................................................... v
Configuring the Public Address Mixer/Amplifiers.................................................... 1
1 Using the Dashboard...............................................................................3
2 Updating Firmware...................................................................................4
3 Setting Network Tab Parameters........................................................6
4 Setting Configuration Tab Parameters .............................................8
5 Accessing Log Files................................................................................ 11
6 Setting DSP Parameters....................................................................... 13
6.1 Setting the Channel Level................................................... 16
6.2 Signal LED, Clip LED, and VU Meter ............................... 16
6.3 Muting a Channel .................................................................. 16
6.4 Adjusting Volume Levels..................................................... 16
6.5 Selecting Input Type, Mic Gain, and
Phantom Power ...................................................................... 17
6.6 Adjusting Compression Settings...................................... 17
6.7 Ducker ........................................................................................ 19
6.8 Adjusting the Graphic Equalizer....................................... 21
6.9 Setting High/Low Pass Parameters................................. 23
6.10 Adjusting the Limiter............................................................ 26
6.11 Adjusting Noise Gate Settings.......................................... 27
6.12 Adjusting Parametric Equalizer Settings....................... 29
6.13 Adjusting Router Settings................................................... 30
6.14 Settings ...................................................................................... 32
6.15 Signal Present.......................................................................... 33
6.16 Status.......................................................................................... 35

ii

iii
List of Figures
Figure 1, Nyquist Appliance Login . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2, Appliance Dashboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 3, Firmware Update Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 4, Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5, Appliance Configuration Settings. . . . . . . . . . . . . . . . . . . . 9
Figure 6, Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 7, DSP Page with Channel Drop-Down Menu . . . . . . . . . . 13
Figure 8, DSP Output Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 9, Compressor Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 10, Ducker Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 11, Graphic EQ Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 12, High/Low Pass Parameters . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13, Limiter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 14, Noise Gate Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 15, Parametric Equalizer Settings . . . . . . . . . . . . . . . . . . . . . 29
Figure 16, Router Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 17, Settings Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 18, Signal Present Parameters. . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 19, Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

iv

v
List of Tables
Table 1, Appliance Dashboard Read-Only Fields . . . . . . . . . . . . . . . 3
Table 2, Appliance Dashboard Buttons . . . . . . . . . . . . . . . . . . . . . . . 3
Table 3, Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 4, Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 5, Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 6, DSP Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 7, Compressor Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 8, Ducker Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 9, High Pass/Low Pass Parameters . . . . . . . . . . . . . . . . . . . . 24
Table 10, Limiter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 11, Noise Gate Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 12, Signal Present Parameters . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 13, Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

vi

Configuring the Public
Address Mixer/
1
Configuring the Public Address
Mixer/Amplifiers
Bogen’s Nyquist-based Public Address Mixer/Amplifiers (PAMAs) are
Digital Signal Processing (DSP) based integrated mixer and power
amplifiers designed for paging and public address applications.
Available in 120, 240 and 600-watt models (NQ-PA120, NQ-PA240,
NQ-PA600), the Public Address Amplifiers enable microphone and
line-level source inputs to be integrated into the Nyquist system.
A short press of the appliance’s Reset button reboots the device. If
you press the Reset button for 10 seconds, the appliance returns to
the factory default configuration settings. Returning to the default
configuration settings does not change the appliance’s firmware.
The following sections describe the process for manual configuration.
For information about using Nyquist’s automatic configuration pro-
cess, refer to the appropriate Nyquist System Administrator Man-
ual.
To access the appliance’s UI:
Step 1 Access the appliance’s web UI by doing one of the fol-
lowing:
a On your web browser, enter the IP address for the
appliance as the URL.
b From the Nyquist web UI navigation bar, select Sta-
tions, select Stations Status, navigate to the device
that you want to configure, and then select the Link
icon.
Note: Do not use third-party Chrome browser extensions with the
Nyquist user interface.

2
Step 2 At the Nyquist Appliance - Login page, enter username
and password, and then select Login.
The default username is admin; the default password is
bogen.
The dashboard for the selected appliance appears.
Figure 1, Nyquist Appliance Login
Figure 2, Appliance Dashboard

3
1 Using the Dashboard
The dashboard displays the following read-only fields:
The dashboard also contains the following buttons:
Table 1, Appliance Dashboard Read-Only Fields
Device Type Identifies the physical device used by the
station.
Serial Number Identifies the serial number for the device.
MAC Address Specifies the Media Access Control (MAC)
address, which is a unique identifier
assigned to network interfaces for commu-
nications on the physical network segment.
Firmware Version Provides the firmware version installed on
the station.
Table 2, Appliance Dashboard Buttons
Dashboard Refreshes the dashboard.
Configuration Set-
tings
Accesses the Configuration Settings page
where you can either manually set various
options, such as the SIP Username, or
select to receive configuration settings
from the server.
Network Settings Accesses the Network Settings page where
you can view and set network settings,
such as the static IP address.
Firmware Update Accesses the Firmware Update page where
you can view the current Nyquist version,
check for updates, restore factory settings,
and reboot the appliance.
Logs Accesses log files, which record either
events or messages that occur when soft-
ware runs and are used when trouble-
shooting the appliance.
DSP Accesses the DSP page where you can view
and set parameters for Digital Signal Pro-
cessing (DSP).

4
2UpdatingFirmware
When you select Firmware Update from the appliance’s web UI, the
Firmware Update page appears. From this page you can determine
which Nyquist version the appliance is using and if an update is
required. You can also use this page to restore factory settings and to
reboot the appliance.
Help Accesses the appliance’s online help.
Manual Displays the Nyquist Matrix Mixer Pre-Amp
Configuration Manual.
Logout Logs out of the appliance’s dashboard.
Table 2, Appliance Dashboard Buttons
Note: A Nyquist appliance connected to the Nyquist network
receives a configuration file from the Nyquist server that includes
the latest firmware available from the server. If the firmware is later
than the one installed on the appliance, an automatic firmware
update occurs unless the Firmware parameter for the station is left
blank. Refer to the Nyquist System Administrator Manual for more
information.

5
To use the Firmware Update page:
Step 1 On the appliance web UI’s main page, select Firmware
Update to ensure you have the latest firmware version.
Step 2 Select Upload Firmware to upload firmware from the
server to the appliance.
If you select this option, a popup screen appears that
allows you to select the file that you want to upload.
You can navigate to the file’s location. After you select
the file, select Upload. If Nyquist discovers a new firm-
ware version, the Firmware Update page displays an
Update Firmware button. Select this button if you
want to update the appliance’s firmware to the new
version.
Step 3 If you want to return your appliance to its original state
(undoing firmware updates), select Restore Factory
Settings.
Step 4 Select Reboot Appliance to restart your appliance.
Figure 3, Firmware Update Page

6
3 Setting Network Tab Parameters
Network settings can be configured dynamically by the Nyquist
server or manually by using the appliance’s web UI.
To manually configure network settings:
Step 1 On the appliance web UI’s main page, select Network
Settings.
Step 2 Select your desired network settings.
Step 3 Select Save.
Figure 4, Network Settings

7
Network settings are described in the following table:
Table 3, Network Settings
Static IP Identifies the fixed IP address assigned
to the appliance by a system administra-
tor.
Netmask Identifies the subnetwork subdivision of
an IP network.
Gateway Identifies the address, or route, for the
default gateway.
VLAN ID Identifies the Virtual Local Area Network
(VLAN) for this appliance. Values range
from 0 to 4094.
VLAN Priority Identifies the priority of the network traf-
fic on the VLAN. Priority can range from
0 through 7.
NTP Server Identifies the IP address or the domain
name of the Network Time Protocol
(NTP) Server. This field is read only.
TFTP Server Identifies the IP address of the Trivial File
Transfer Protocol (TFTP) server. TFTP is
used by Nyquist VoIP phone and appli-
ance provisioning. A TFTP server runs on
the Nyquist server on port 69 (the stan-
dard TFTP port #).
Device provisioning files are stored on
the Nyquist server in directory: /srv/
tftp. This is the only directory
exposed by the TFTP server.
DHCP Server Over-
ride
Indicates if you want to override the
TFTP server information provided by the
Dynamic Host Configuration Protocol
(DHCP) via option_66.
DHCP supplies IP addresses to the
Nyquist server and associated devices. It
also supplies the TFTP server IP address
or name via option_66.

8
4 Setting Configuration Tab Parameters
The easiest way to configure Nyquist appliances is to obtain configu-
ration settings from the Nyquist server by selecting Get Configura-
tion From Server. However, you can manually configure an
appliance through the appliance’s Web UI.
To manually configure your Nyquist appliance:
Step 1 On the appliance Web UI’s main page, select Configu-
ration Settings.
Step 2 Select your desired settings.
Step 3 Select Save.
DHCP Enabled Indicates if the device is enabled to use
DHCP.
Reboot Appliance Allows you to save the network options
and reboot the appliance.
Table 3, Network Settings (Continued)
Note: Manual configuration will be overwritten by the server once
the appliance is connected and discovered by the server.

9
The following table describes the Configuration tab settings:
Figure 5, Appliance Configuration Settings
Table 4, Configuration Settings
Web Username Provide a web username for this appli-
ance.
Web Password Provide a web password for logging into
the appliance.
Web Confirm Pass-
word
Re-enter the password used to log into
the appliance.

10
The following parameters appear for each port associated with the
appliance:
SIP Username Provide the username used for Session
Initiation Protocol (SIP) device registra-
tion.
SIP Password Provide the password used for SIP device
registration.
SIP Confirm Pass-
word
Re-enter the password used for SIP device
registration.
Server Identifies the IP address of the Nyquist
server.
Local Port Identifies the local port.
Emergency-All-Call Identifies the IP address, port number, and
volume used for emergency all-calls
pages.
All-Call Identifies the IP address, port number, and
volume used for all-calls pages.
Audio Distribution Identifies the IP address, port number, and
volume used for audio distribution.
Multicast # Identifies the multicast IP address for a
zone that the speaker is included in. If a
speaker is added to multiple zones, the
multicast IP address for each zone
appears.
Port Number Identifies the port number of the appli-
ance.
Port Type Identifies the device type that the port
connects to.
Account ID Provides the SIP account (IP address) asso-
ciated with the device preceded by the
extension of the device associated with
this port.
Local Port Provides the port used for SIP.
Username Identifies the username or extension for
the station associated with the port.
Table 4, Configuration Settings (Continued)

11
5 Accessing Log Files
A log file records either events or messages that occur when software
runs and is used when troubleshooting the appliance. From the
appliance’s web-based UI, log files can be viewed directly or exported
via download to your PC, Mac, or Android device and then copied to
removable media or attached to an email to technical support.
To view a log file:
Step 1 On the appliance Web UI’s main page, select Logs.
Step 2 From the drop-down menu, select the log that you
want to view.
Multiple versions of the same log and zipped copies of
the log may be available.
Step 3 To export the file, select Export.
A link to a .txt file appears in the screen’s lower left.
Figure 6, Logs

12
Available logs are described in the following table:
Table 5, Logs
Log Description
alternatives.log Contains information by the update-alternatives, which
maintain symbolic links determining default com-
mands.
ampws.log Contains information about protection status and logs
protection events with temperature information at the
time of event.
auth.log Contains system authorization information, including
user logins and authentication methods that were
used.
bootstrap.log Contains information actions, errors, and warnings that
occur during booting of the appliance.
btmp Contains information about failed login attempts.
daemon.log Contains information logged by the various back-
ground daemons that run on the system.
debug Contains errors and debug information.
dmesg Contains kernel ring buffer information. When the sys-
tem boots up, the screen displays information about
the hardware devices that the kernel detects during the
boot process. These messages are available in the ker-
nel ring buffer, and whenever a new message comes,
the old message gets overwritten.
dpkg.log Contains information that is logged when a package is
installed or removed using dpkg command.
faillog Contains user failed login attempts.
kern.log Contains information logged by the kernel and recent
login information for all users.
lastlog Contains information on the last login of each user.
messages Contains messages generated by Nyquist.
php5-fpm.log Contains errors generated by the PHP script.