Bolton Furniture Low Loft User manual

Assembly Sheet
Low Loft
Replacement parts can be obtained from any Bolton Furniture authorized dealer
249 Professional Drive, Morrisville, VT
Phone: [phone]
Fax: [phone]
Web Site: www.boltonfurniture.biz

Ladder & Guardrail Parts List Low Loft Parts List
Low Loft Assembly: Two people recommended for this assembly.
Step 1
Open all boxes and verify that all parts are included.
Step 2 - Install Threaded Inserts
PARTS LIST
Un-pack the Headboard and Footboard from bed
b
ox. Using Hex Wrench (E) Install Threaded Insert
(F) into pre-drilled holes on bottom edge of
Headboard and Footboard Bed Posts (4 places).
SEE DIAGRAM
A
Qty.
DescriptionDrawing
NO.
1
Back Support Rail
4
Leg Extension
B
Mushroom Plug 12
4
1
4
Headless Rod
M8 Hex Wrench
Cross Dowel
4
80mm Hex Bolt
H
G
E
D
Qty.
DescriptionDrawing
NO.
C
FM8 Insert 4
IM6 Hex Wrench 1
E
F
Bed Post
F
1
2
Front Guardrail 1
GBack Guardrail 1
H
30mm wood screw
4
EM6 Hex Wrench 1
3
50mm Hex Bolt
D
A
NO. Drawing Description Qty.
B
C
Ladder 1
20mm wood screw
6
2
Hook
249 Professional Drive, Morrisville, VT
Phone: [phone]
Fax: [phone]
Web Site: www.boltonfurniture.biz

Step 3
Assemble bed per instructions included with bed.
Step 4 - Install Headless Rod
Step 5 - Attach Leg Extentions
Support rail
Leg extention
Step 6 - Attach Long Guardrail
Lay assembled bed on its side - with counter sunk
holes facing out make sure profile on the Leg
Extentions match the profile on Bed Post. Attach 4
Leg Extentions (A) to Bed Post by threading
headless rod into insert in bottom edge of Bed Post.
Secure tightly. At this time Set bed up-right on 4
legs.
Thread Headless Rod (G) into threaded insert in Leg
Extention (A) - 4 places. Make sure Headless Rod
is threaded in at least 1/4" into insert in Leg
Extention (A).
Counter Sunk Holes facing
out - 4 places
Determine side of bed you want the long guardrail
on. Position the long guardrail over siderail (you
may need to loosen bed bolts)
Attach Support Rail - Attach Back Support Rail
(B) to back Leg Extentions using using 80 MM Hex
Bolt (C) and Cross Dowel (D). Insert the Cross
Dowels into pre-drilled holes in Back Support Rail -
Align thru holes in Leg Extentions to pre-drilled
holes in edge of Back Support Rail. Thread Hex
Bolt into Cross Dowel. Tighten using Hex Srench
(I).
Secure Long Gardrail to footboard end of bed using
50 MM Bed Bolt (D). Tighten with Hex Wrench
(E). Next attach long guardrail to inside of side rails
using 30 MM wood screw (H) - 2 places
Loosen Bed Bolts if necessar
y
to attach Long Guardrail
G
A
G
Be d Po s t
A
DI
A
BC
Foot boar d
G
E
D
H
Si der ai l
249 Professional Drive, Morrisville, VT
Phone: [phone]
Fax: [phone]
Web Site: www.boltonfurniture.biz

Step 7 - Attach Ladder Hooks
required 2 places
Step 8 - Attach Ladder and Short Guardrail
Position the Ladder Hooks over the side rail on
footboard end of bed and the short guardrail over the
side rail. Secure the Ladder to bed end and short
guardrail using 50 MM Hex Bolt (D) - 2 places.
Using 20 MM Wood Screw (B) secure ladder hooks
to inside of siderail.
Attach Hook (C ) to Ladder (A) using 20 MM Wood
Screws (B) - 2 places. Secure tight.
You are now ready to add Tent Fabric or cases to your Low Loft Configurations
Using 20 MM Wood Screw (B) secure short
guardrail to inside of siderail.
Si deRai l
F
H
H
249 Professional Drive, Morrisville, VT
Phone: [phone]
Fax: [phone]
Web Site: www.boltonfurniture.biz

Safety Warnings:
STRANGULATION HAZARD
12) If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed should be placed
against the wall to prevent entrapment.
13) Always use guard rails on both sides of the upper bunk.
9) Always use the ladder for entering and leaving the upper bunk.
10) Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
11) Use of a night light may provide an added safety precaution for a child using the bunk.
6) Prohibit more than one person on the upper bunk.
8) Do not allow horseplay on or under the bed and prohibit jumping on the bed.
3) Always use the recommended size mattress to help prevent the likelihood of entrapment or falls. Use a mattress
which is 75” long and 53 1/2" wide on the lower bed (full size).
7) Periodically check to ensure that the guard rails, ladder, and other components are in their proper position, free
from damage, and that all connectors are tight.
14) The use of water or sleep flotation mattresses is prohibited.
15) Keep these instructions for future reference.
A flat Mushroom Cap – made to conform to the requirement is provided to take the place of finials in the upper
structure in Bunk Bed configurations.
Using the finials in the upper structure of a Bunk Bed will create a strangulation hazard. Never use finials in the
upper structure of a Bunk Bed.
Warning - On Beds with finials that can be configured as Bunk Beds!
Effective on Bunk Beds manufactured on or after March 10th, 2008, finials cannot be used.
The finials provided with certain beds, which are part of the design of the bed, are to be used only in one of the
lower configuration – that is as a Twin, Full, Queen or King configuration.
These finials are never to be used in the upper structure in a Bunk Bed configuration.
15) Never attach or hang items to any part of the bunk bed that are not designed for use with the bed. For example,
but not limited to hooks, belts or jump ropes.
5) Do not allow children under 6 years of age to use the upper bunk.
1) Follow the information on the warning label attached to the upper bunk end structure. Do not remove this label.
2) Always use the recommended size mattress to help prevent the likelihood of entrapment or falls. Use a mattress
which is 75” long and 38 ½” wide on the top bunk.
4) Surface of mattress must be at least 5 inches below the upper edge of the guard rails. Ensure thickness of mattress
and foundation combined does not exceed 8”.
249 Professional Drive, Morrisville, VT
Phone: [phone]
Fax: [phone]
Web Site: www.boltonfurniture.biz