Bond HYMH20027-61 User manual

Owner’s Manual
Item#
Model#
HYMH20027-61
10" ROUND GAS FIRE COLUMN
52145
DANGER CARBON MONOXIDE HAZARD
This appliance can produce carbon
monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed
space such as a camper, tent, car or
home.
INSTALLER: Leave this
manual with the appliance.
CONSUMER: Retain this
manual for future reference.
DANGER
WARNING
WARNING
WARNING
For outdoor use only.
Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Refer to the owner's information manual provided with this appliance.
For assistance or additional information consult a qualified installer, services agency or
the gas supplier.
FIRE OR EXPLOSION HAZARD
If you smell gas:
Shut off gas to the appliance.
Extinguish any open flame.
If odor continues, leave the area immediately.
After leaving the area, call your gas supplier
or fire department.
Failure to follow these instructions could
result in fire or explosion, which could cause
property damage, personal injury, or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance. An LP-cylinder not connected
for use shall not be stored in the vicinity of
this or any other appliance.
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury, or loss of life.
•
•
•
•
Installation and service must be performed
by a qualified installer, service agency,
or the gas supplier.

Bond Manufacturing Co., Inc. | Page 2
WARNING
Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so
SAFETY INFORMATION
•
•
•
•
•
burner obstructions before use.
•
•
•Combustible materials should not be within 60 inches of the top of the unit, or within 48 inches
around the entire unit.
•
•
anywhere near the appliance.
•Users should be alerted to the hazards of high surface temperatures and keep a safe distance to
avoid burning or clothing ignition.
•
Do not transport it while in operation.
•
•
•
unit.
•Keep ventilation openings in cylinder enclosure (FIREBOWL BODY) free and clear of debris.
•
•
•
•The conversion or attempted use of natural gas in a propane unit is dangerous.
•
•Keep any electrical supply cord and the fuel supply hose away from any heated surfaces.
•
•Inspect the burner before each use of the appliance. If there is evidence of damage, the burner must
be replaced prior to the appliance being put into operation. Use Manufacturer approved or supplied
replacement burner only.
•
used.
•
•A dented or rusty propane cylinder may be hazardous and should be checked by your gas supplier
prior to use.
•
•The installation of this unit must adhere to local codes or Propane Storage and Handling Code,
CSA B149.2.
Solid fuels shall not be burned in this appliance. Never place clothing or other flammable
material on or near the firebowl.

1-866-771-2663 | Page 3
•
•Transport and store the empty gas cylinders carefully and properly.
•If you see, smell or hear the hiss of escaping gas from the propane cylinder: 1. Disconnect propane
gas cylinder, 2. Do not attempt to correct the problem yourself, 3. Get to your gas supplier and/or the
•
operating this appliance.
•
•This appliance is designed for use with a 16.40Z (1Lb) propane gas cylinder (disposable). The
cylinders of the U.S. Department of Transportation (DOT) or the National Standards of Canada, CAN/
CSA-B339, cylinders, Spheres and Tubes for Transportation of Dangerous Goods;and Commission,as
applicable.
•Cylinders must be stored outdoors in well-ventilated area out of the reach of children.
•Disconnected cylinders must have valve caps tightly installed and must not be stored in a building or
any other enclosed area.
•Do not light or use gas unit if lava rocks are wet. Ensure lava rocks are completely dry before
igniting.
•Pumice stones/lava rocks/LavaGlass®could hit somebody’s face or eyes during initial start of this
•During Ignition procedure, one should NEVER get his/her face close to and or above the burner. In
•Children should never operate this unit. Children must be supervised while near this unit.
•
inspected annually and cleaned regularly.
•Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
•Young children should be carefully supervised when they are in the area of the appliance.
•
near the appliance.
•Any guard or other protective device removed for servicing the appliance shall be replaced
prior to operating the appliance.
•
may be required as necessary. It is imperative that the control compartment, burners and
circulating airways of the appliance are kept clean.
The cylinder must be disconnected when the appliance is not in use.
Do not use a propane cylinder with a damaged valve and any other worn out parts.
Maximum gas supply: 250 psi; Min. gas supply: 10 psi.
•

Bond Manufacturing Co., Inc. | Page 4
SAFETY INFORMATION
Combustible materials should not be within 60
inches of the top of the unit, or within 48 inches
around the entire unit.
Min. Clearance
48 in (121.9 cm)
Min. Clearance
48 in (121.9 cm)
Min. Clearance
48 in (121.9 cm)
Min. Clearance
48 in (121.9 cm)
Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied
directly by Bond Manufacturing Co., Inc.
Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate
the appliance. For assistance with repair or replacement of the burner or any other parts, call Bond
Manufacturing Co., Inc. at 1.866.771.2663.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas
valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.

1-866-771-2663 | Page 5
CONTENTS
Item Description Qty
A Lava Rocks 1 box (0 . 7kg)
B 1
C
Body
1
D 1
E
Protective Cover
1
F
Control Knob (preassembled)
1
G
Burner (preassembled)
Guard (preassembled) 1
A
G
F
C
B
D
E
Door (preassembled)

Bond Manufacturing Co., Inc. | Page 6
ASSEMBLY INSTRUCTIONS
3 . Place the lava rocks (A) onto the burner
(F) evenly.
WARNING
Keep away from the unit and have the unit to
burn 20 minutes for the first time use.
Always ensure that lava rocks/pumice stones/
LavaGlass®are completely dry before use. Failure
to do so will cause them to crack or pop.
To attach the 1 lb. propane gas tank
in the body (B), screw it to the regulator inlet
fitting inside the body (B).
1. Check that the control knob (E) for the gas
supply system is turned to the “OFF” position
before starting any assembly.
E
2.Open the door. (not included)
A
G
To ensure proper function, the guard (G) on this
burner (F) should be free of lava rocks at all times.

1-866-771-2663 | Page 7
OPERATION
To Light
To Extinguish
Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor
area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off”
position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles
occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the
gas valve off, disconnect propane gas tank and do not use the appliance until the leak is
repaired.
Pumice stones/lava rocks/LavaGlass®could pop up and strike somebody’s face during the process
should be a yellow/blue color between 1 - 7.5 inches in height.
1. Turn the control knob (E) clockwise to the ‘off’ position.
2. Disconnect propane cylinder to close the gas supply if not using for a period of time.
heating item.
1. After assembling the gas tank, push and turn the control knob (E) counter-clockwise, then use
a match or a lighter to light the firebowl. Keep holding down the control knbo for 15 seconds.
2. To adjust the flame, turn the control knob (E).

Bond Manufacturing Co., Inc. | Page 8
MAINTENANCE
•Before performing any maintenance always disconnect propane gas tank.
•Keep the heating item free and clear from combustible materials.
•Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
•Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/
lava rocks/LavaGlass®are completely cooled down. Wipe down with a soft cloth.
•Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
•Permanent damage may occur if powder or solvent comes in contact with painted or plastic
components on this heating unit.
•Keep the heating unit stored away from direct sunlight.
• If storing this unit inside, disconnect the propane gas tank from the gas valve.
•Not using manufacturer approved or supplied parts/accessories may result in a defective condition
and void the warranty of this heating unit.
• Always place lid (if applicable) or protective cover on heating item when not in use.
Store your product indoors during winter months. Avoiding extreme cold temperatures will
prevent from exposure damage.
•

1-866-771-2663 | Page 9
TROUBLESHOOTING
Problem Cause Solution
No gas flow Check if gas cylinder is empty
Regulator isn’t connected securely to the
tank
Tighten regulator connection to the gas
tank
Spider webs or insect nest in the burner
and guard
Check the burner and guard
Burner ports are clogged Turn all gas flow connections off. Insert
an opened paperclip (or similar item) into
each of the burner ports to clear them
out.
Heating unit emits a lot of
black smoke
Flame is obstructed at burner ports Check that all burner ports are free of
any small lava rocks/pumice stones/
LavaGlass®pieces
High or gusting winds Increase flame to ‘high’
No gas flow Check if gas cylinder is empty
Burner won’t light with
a match
Flame blows out
easily

Bond Manufacturing Co., Inc. | Page 10
WARRANTY
If you have any questions or concerns, please contact Bond Manufacturing Co., Inc. at the below
resources:
CONTACT
Toll Free Phone [phone]-BOND (2663) | Monday - Friday, 8am - 4:30pm PST
Email customer[email protected]
Online www.bondmfg.com
This product has a one-year warranty against manufacturing defects in workmanship, or materials.
The manufacturer warranty will be voided by, and manufacturer disclaims any responsibility for, the
following actions:
•
•Use of any component part not manufactured or approved by Bond Manufacturing Co., Inc.
•Use and installation other than what is listed in this manual.
Please contact the manufacturer for replacement parts.