BonsenKitchen VS3803 User manual

Vacuum Sealer
Operation Instructions
Model: VS3803
Customer service: 1-888-965-8032
customer[email protected]

2
Introduction
Congratulations on the purchase of this modern and high-quality product. This
instruction manual contain is important information on safety, usage and disposal.
Before using the product, familiarize yourself with all handling and safety guidelines.
This appliance may only be used as described and for the purposes indicated. Please
also pass these operating instructions on to any future owner(s)
Safety Instructions
Always abide by the following safety rules and instructions when using electrical
appliances and read these instructions carefully before using the vacuum sealer.
Read all instructions
Do not touch hot surfaces Use handles or knobs.
To protect against electric shock do not immerse cord or main unit in water or other
liquid.
Close supervision is necessary when any appliance is used by or near children.
Unplug from outlet when not in use and before cleaning.
Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or has been damaged in any manner. Contact customer service for
examination, repair or adjustment.
S
Do not use outdoors.
Do not let cord hang over edge of table or counter, or touch hot surfaces.
Do not place on or near a hot gas or electric burner, or in a heated oven.
Do not open the appliance cover during operations.
Always ensure the upper/bottom cover in correct location during operations.
This product is only authorized for domestic use and not for commercial or industrial
purposes. It is only intended for applications described in these instructions.
This vacuum sealer may be used by children aged 8 years old and over if they are
supervised by an adult and have been told how to use the appliance safely and are
aware of potential risks.

3
Cleaning and maintenance may not be carried out by children unless they are 8
years old or older and are supervised.
Children must not play with the vacuum sealer.
WARNING: Do not immerse the vacuum sealer in water or other liquids when cleaning
it. If the supplied power cord is damaged, it should be replaced by a qualified technician
in order to avoid a hazard.
SAVETHESE INSTRUCTONS
OPERATING INSTRUCTIONS
If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified person in order to avoid a hazard.
A short power-supply cord is to be provided to reduce the risk resulting from
becoming entangled in or tripping over a longer cord.
Longer extension cords are available and may be used if care is exercised in their
use.
If a extension cord is used,
1) The marked electrical rating of the extension cord should be at least as great as
the electrical rating of the appliance;
2) If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord; and
3 )The longer cord should be arranged so that it will not drape over the countertop or
table top where it can be pulled on by children or tripped over unintentionally.
Placement
Always place the vacuum sealer away from the edge of the countertop
Make sure the vacuum sealer is placed on a firm, flat surface.
Do not use the vacuum sealer outdoors or near water
WARNING: Do not place the vacuum sealer onto a metal tray or metal surface when
in use.
Personal Safety
WARNING: To protect against fire, electric shock and personal injury, do not immerse
the plug and vacuum sealer in water or any other liquid.
WARNING: Misuse of the vacuum sealer can cause personal injury.

4
Disconnect the vacuum sealer from power before cleaning and not in use.
Allow the vacuum sealer to cool down before putting on or taking off parts and
before cleaning.
Do not move the vacuum sealer while it is switched on.
Other Safety Considerations
Only use officially-provided attachments and accessories.
Do not use the vacuum sealer for any use other than its intended purpose.
Keep the vacuum sealer away from heat sources.
When using the vacuum sealer, make sure the lid is properly in place and secure
before operation.
CAUTION: To prevent damage to the vacuum sealer, do not use water or any liquid
when cleaning.
Disposal of packaging materials
The packaging protects the appliance from damage during carriage.
The packaging materials have been selected for their environmental friendliness
and ease of disposal, and are therefore recyclable.
Returning the packaging to the materials cycle conserves raw materials and
reduces the amount of waste that is generated. Dispose of packaging materials that
are no longer needed in accordance with applicable local regulations.
NOTE:
►If possible, keep the original packaging during the warranty period so that the device
can be properly packed for returning in the event of a warranty claim.
Scope Delivery
The appliance is supplied with the following components as standard:
1 x Vacuum Sealer
1 x Roll Vacuum Bag
1x Cutter
►Check the package for completeness and for signs of visible damage.
►If the consignment is incomplete or damaged due to defective packaging or carriage,
please contact us.
Installation Requirements
For safe and trouble-free operation of the device, the set-up location must fulfill the
following requirements:

5
When setting it up, place the appliance on a firm, flat and horizontal surface.
Do not place the device in a hot, wet or extremely damp environment or in the
vicinity of flammable materials.
The mains power socket must be easily accessible, so that the power cable can be
easily disconnected in the event of an emergency.
Electrical Connection
►Before you connect the appliance, compare the connection data (voltage and
frequency) on the data plate with that of your mains power network. These data must
agree so that no damage issue stained by the device.
►Ensure that the power cable is undamaged and is not routed over hot surfaces and/or
sharp edges.
►Ensure that the power cable is not taut or kinked.
►Do not let the power cable hang over edges (trip wire effect).
►Insert the plug into the mains power socket.
Sealing vacuum bags
►The bag width may not exceed 11.81Inch. Otherwise it can not be welded correctly.
►Use only nylon-PE films with a structure (points or grooves) on one side and that have
a structure(points or grooves) on one side and a thickness of approximately 0.006
-0.012 inch(6.8- 11.6mil).Otherwise the weld seam will not be tight and the appliance
may be damaged. You can recognize bags of this type from the information on the
package. The quality of the weld seam will vary depending on the type and thickness
of the bag.
►Cut the desired length for your bag from the roll. Open the appliance lid by pressing
the lid release and open the lid upwards. Lay the open end of the bag as far into the
appliance so that the opening of the bag is located central under the lower sealing
ring. The bag should be inserted no further than the behind sealing ring and must lie
between the front sealing ring. If the bag lies over one or both of the two sealing ring,
then the bag cannot be correctly welded.
►The bag opening must lie flat on the welding wire. Otherwise the welding does not
work properly. Close the appliance lid. The press seal presses the bag onto the
welding wire, to create a smooth seam. Ensure that both corners of the appliance lid
closed. If necessary, press the upper cover again and so that the appliance lid clicks
into place and locks tightly. Press the Food button Mode Selection. If the choice is dry,
the dry indicator will light on. If the moist is chosen, the moist indicator will light on.
►Ensure that the weld seam is properly closed. A correct weld seam should be a
smooth, straight stripe without any creases.

6
►Fill the bag so that no food scraps or liquids can leak out during welding and get into
the appliance.
►Wait 15 seconds before sealing the next bag to allow the appliance to cool down.
Parts
1）Seal/Cancel 2）Val seal
3）Suction Interface 4）Out Vac
5）Food 6）Heating Seal
7）Open Button 8）Sealing ring
9）Vac Chamber 10)Sealing Rubber Strip
11）Cutter

7
Functions &Vacuuming
1) Seal
In standby state according to this, press the seal button, the sealing indicator will light
on, you can begin seal the bag.
2) Stop
The machine will stop working when the button is pressed in any state of work.
3) Vac Seal
Press this button in standby state, the machine will start vacuuming, then sealing the
bag, the Vac Seal indicator light on.
4) Out Vac
Connect one end of the vacuum pipe with the external vac hole, and the other end with
canister, then press the “Out Vac” button, the device will start vacuuming. If need stop
the vacuum, press the button “Seal/Stop”.
5) Food-Moist/Dry
You can choose the mode according to what you want to seal, dry or moist. If you seal
dry food, advice to wait after 10 seconds to seal next one.
If you seal moist food, advice to wait after 20 seconds to seal next one.
Turn on the appliance power, the default mode is dry, when the upper and lower cover is
not locked tight, only this button “food” can adjust the mode.
It is recommended to seal 5 bags continuously then cool down 10min, so that the
machine life can be prolonged.
6 ) Suction Interface
Connect one end of the vacuum pipe with the external vac hole, and the other end with
canister, then press the “Out Vac” button, the device will start vacuuming. If need stop
the vacuum, press the button “Seal/Stop”.

8
7) Indicator Light
(1)Seal indicator light
Press “seal/stop” button, the light will be red. After seal, light go out. Press this button
again, seal function stop, light go out.
(2) Vac seal indicator light
Press ”Vac seal” button, the “Vac” indicator light will be green. After Vac seal, the “seal”
and “Vac” light will be on until the function is completed. The machine will stop working
when the “Seal/Stop” button is pressed in any state of work.
(3)Dry/moist indicator light
Turn on the power, when the upper and lower cover is not locked tight, the dry indicator
is flashing, when the dry and moist lights on at the same time, that means the
appliance occur over heating, After the lights go out, the appliance can start to work
normally.
8) Cutter
This appliance is equipped with a cutter, please just slide it to cut the roll bag.
NOTE: Once you have sealed (dry food) 10 bags continuously, allow the appliance to
cool down for about 10 minute. But if you seal moist food, only seal 6 bags continuously
must need cool down 10 minute. During this cool-down phase, you cannot start the
appliance. After the cool-down phase, you can use the appliance as normal.
To ensure the sealing effect, advise that the food in the package should be kept
8cm(3.14 Inch) away from the seal so that the open end of the bag can be put into the
vacuum chamber of the machine.

9
Cleaning
►Remove the plug from the mains power socket before beginning to clean the device.
►Ensure there isn’t moisture can penetrate the device during leaning.
►Do not use aggressive or abrasive cleaning agents, as these may corrode the surface
of the casing.
►Do not use any hard or sharp objects to remove any adhesive from the welding wire.
Otherwise the welding wire or the insulation could be damaged.
►Clean the surface of the appliance with a lightly moistened cloth and a mild
detergent.
►Wipe off the upper and the lower sealing rings, as well as the press seal with a damp
cloth. Ensure that the appliance is dry before using it again.
►Washable parts
Press the button on both side to open the appliance to the top and bottom panel at 90
degrees, then can take out the drip tank. All the drip tank panel (below tick part)
can use a dishwasher and other equipment to wash it. But attention below tick
part can not wash it. Also to note the appliance must be turned off the power before you
wash it.
Storage
►The appliance has a built-in cable retainer on the underside of the housing, on which
you can wrap the power cable when it is not in use. This prevents the power cable
from getting caught or soiled, or becoming a source of danger by hanging loosely
down.
►Store the appliance in a clean, dry place away from direct sunlight.

10
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
Please have the till receipt available as proof of purchase. You will find the item umber
as a sticker on the rear or bottom of the appliance.
If function or other defects occur, please contact the service centre listed either by
telephone or by email.
If you have any further assistance, please contact us:
Customer service: 1-888-965-8032
[e-mail]
Warranty:
The warranty for this appliance is for 12 months from the date of the first purchase. The
warranty covers only claims for the material and manufacturing defects, but not for the
transport damage, wearing parts or for damage to fragile components, e.g. button or
seal ring.
The warranty is void in the case of the abusive and improper handling, use of force and
internal tampering not carried out by our authorized service branch. Your statutory rights
are not restricted in any way by this warranty. The warranty period is not extended by
repairs made under the warranty. This applies also to replaced and repaired parts. The
appliance has been manufactured with care and meticulously examined before delivery.
Please keep your receipt as proof of purchase.
Please contact with our Customer Service in case of a warranty claim.
Technical Data
Model No.: VS3803
Operating Voltage: 120V~ 60Hz
Power Consumption: 125W
Max. Width for Shrink-wrapping: 300mm（11.81Inch）
Vacuum Value: -50Kpa
Noise Level: about 70 dB
Product Dimension: 387*101*69mm (15.24*3.98*2.72Inch)