Bosch Greenstar Camray Utility 12/18 User manual

GREENSTAR CAMRAY UTILITY &
UTILITY SYSTEM
FLOOR STANDING OIL FIRED CONDENSING BOILER
CONVENTIONAL FLUE & ROOM SEALED FLUE
FOR FULLY PUMPED OPEN VENT OR SEALED CENTRAL HEATING SYSTEMS AND
DOMESTIC HOT WATER CYLINDERS
For use with the following Greenstar oil fired appliances:
Greenstar Camray Utility 12/18, 18/25, 25/32
Greenstar Camray Utility System 12/18, 18/25, 25/32
THE APPLIANCE IS FOR USE WITH 28
SECOND KEROSENE ONLY
GB
USER INSTRUCTIONS
& CUSTOMER CARE GUIDE

USER INSTRUCTIONS &
CUSTOMER CARE GUIDE
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
CONTACT INFORMATION
Worcester, Bosch Group:
Service call centres:
UK TEL: [phone]
FAX: [phone]
SCOTLAND ONLY FAX: [phone]
Other enquiries: TEL: FAX:
MAIN RECEPTION: 01905 754624 754619
TECHNICAL: 08705 266241
SPARES: 01905 752571
LITERATURE: 01905 752556
SALES: 01905 752640
WEBSITE: www.worcester-bosch.co.uk
WATER TREATMENT:
FERNOX 01799 550811
www.fernox.com
SENTINEL 0151 420 9595
www.betzdearborn.com/sentinel
FLUE TERMINAL GUARDS:
WORCESTER, BOSCH GROUP
OIL FIRING TECHNICAL ASSOCIATION:
OFTEC 0845 6585080
www.oftec.org
USER INSTRUCTIONS &
CUSTOMER CARE GUIDE
PLEASE READ THESE INSTRUCTIONS
CAREFULLY BEFORE OPERATING YOUR
APPLIANCE.
THESE INSTRUCTIONS ARE APPLICABLE
TO THE WORCESTER, BOSCH GROUP
APPLIANCE MODEL(S) STATED ON THE
FRONT COVER OF THIS MANUAL ONLY AND
MUST NOT BE USED WITH ANY OTHER
MAKE OR MODEL OF APPLIANCE.
IF YOU ARE IN ANY DOUBT CONTACT THE
WORCESTER, BOSCH GROUP TECHNICAL
HELPLINE.
PLEASE KEEP THESE INSTRUCTIONS WITH
THE INSTALLATION AND SERVICING
INSTRUCTIONS IN A SAFE PLACE OR WITH
THE APPLIANCE AFTER INSTALLATION OR
SERVICING.
DO NOT INTERFERE WITH ANY SEALED
COMPONENTS.
ABBREVIATIONS:
Ø Diameter.
CH Central Heating.
DHW Domestic Hot Water.
TRV Thermostatic Radiator Valve.
IP Ingress Protection.
CF Conventional flue.
RS Room sealed flue.
N/A Not allowed.
SEDBUK Seasonal Efficiency for Domestic
Boilers in the United Kingdom.
OFTEC Oil Firing Technical Association for the
Petroleum Industry.

CONTENTS
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
1
INTRODUCTION
USING YOUR
APPLIANCE
MAINTENANCE ENERGY
SAVING
GUARANTEENOTES
CONTENTS
INTRODUCTION
SAFETY PRECAUTIONS 2
EXCELLENCE COMES AS STANDARD 3
GENERAL INFORMATION 4-6
USING YOUR APPLIANCE
CONTROLS 7
OPERATING THE APPLIANCE
Switching the boiler on/off 8
Setting the heating temperature 8
Controlling central heating 8
Fault conditions 9
ENERGY SAVING
TIPS ON ENERGY SAVING 10-11
MAINTENANCE
MAINTAINING YOUR APPLIANCE 12
FAULT FINDING 13
FAULT OR BREAKDOWN 14
GUARANTEE
YOUR GUARANTEE 15
GUARANTEE REGISTRATION 16

GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
2
SAFETY PRECAUTIONS
FITTING & MODIFICATIONS:
Fitting the appliance and any controls to the
appliance may only be carried out by a
competent engineer in accordance with the
relevant Installation Regulations.
Flue systems must not be modified in any
way other than as described in the fitting
instructions.
Any misuse or unauthorised modifications to
the appliance, flue or associated
components and systems could invalidate
the warranty. The manufacturer accepts no
liability arising from any such actions,
excluding statutory rights.
This appliance is suitable for use with 28
second kerosene only, no other fuel must
be used.
SERVICING:
The user must have the system regularly
serviced by a competent, qualified OFTEC
registered engineer using approved spares,
to help maintain the economy, safety and
reliability of the appliance.
The appliance should be serviced once each
year after installation unless the installation
conditions and usage demand more frequent
services.
DO NOT OPERATE THE APPLIANCE WHEN:
4The appliance, flue or system is incorrectly
fitted, faulty or damaged.
4The flue terminal outlet fitted on the outside
wall or roof is obstructed or damaged.
4There are fumes, fuel leaks or fuel smells
from the fuel supply, appliance or flue system.
4The system is empty, frozen or unpressurised
(sealed systems).
4The condensate pipe is blocked or restricted.
4The appliance clearances are inadequate.
4The air supply is restricted or vents damaged.
INTRODUCTION
OIL SMELLS, LEAKS OR FUMES FROM THE
APPLIANCE:
4Extinguish any naked flames.
4Open windows and doors.
4Switch off the appliance electricity supply.
4Isolate the fuel supply to the boiler.
4Contact installer/service engineer.
HEALTH & SAFETY:
The appliance contains no asbestos and no
substances have been used in the
construction process that contravene the
COSHH Regulations (Control of
Substances Hazardous to Health
Regulations 1988). Where applicable, the
CE mark indicates compliance with relative
EU Directives.
COMBUSTIBLE AND CORROSIVE
MATERIALS:
Do not store or use any combustible
materials (paper, thinners, paints etc.) inside
or within the vicinity of the appliance.
The combustion air must be kept clear of
chemically aggressive substances which can
corrode the appliance and invalidate any
warranty.
SAFETY PRECAUTIONS

EXCELLENCE COMES AS
STANDARD
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
3
INTRODUCTION
EXCELLENCE COMES AS
STANDARD
Thank you for purchasing a Greenstar oil fired
condensing boiler from Worcester, Bosch
Group. The company prides itself on
manufacturing boilers to the strictest quality
control standards throughout every stage of
production.
Worcester, Bosch Group has led the field in
innovative appliance design and performance for
more than 40 years. This heritage means all
products are of exceptional quality and proven
reliability.
The condensing range in particular, is extremely
energy efficient, converting more of the fuel
consumed into heat offering you economical
running costs and value for money. It sits in
SEBUK band A, at the top of the energy rated
appliances available.
There is also the assurance of our no-nonsense
parts and labour guarantee - backed up by an
optional servicing and maintenance contract to
keep your boiler operating at peak condition and
efficiency.
To find out more about Worcester, Bosch
Group, use the 'Contact Information' shown on
the inside front cover.

GENERAL INFORMATION
CONDENSATE:
This is a high efficiency appliance using
condensing technology which will under normal
operation produce a regular discharge of
condensate to drain and at times, give out a
plume of water vapour from the flue terminal.
ROOM THERMOSTAT:
A room thermostat must be fitted to control the
central heating. Refer to instructions supplied
with the room thermostat for information on
siting and setting.
THERMOSTATIC RADIATOR VALVES:
It is recommended that this type of valve is fitted
to all but one of the radiators (or at least those in
the sleeping accommodation). The remaining
radiator, which must be where the room
thermostat is located, should be un-controlled
and must be left open.
GENERAL INFORMATION GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
4
INTRODUCTION
Read these instructions carefully to get the best
from your appliance.
CENTRAL HEATING SYSTEMS:
During the first few hours of operation of the
central heating system, check that all radiators
are being heated at an even rate.
If the top of a radiator is at a lower temperature
than the bottom then it should be vented by
releasing air through the venting screw at the top
of the radiator. Ask your installer to show you
how this is done. Repeated venting will reduce
the quantity of water in the system and this must
be replenished for safe and satisfactory
operation of the appliance.
When excessive venting or water leaks are found
in the system you must contact a service
engineer to inspect the installation and rectify
any fault.
Only use additives compatible with the appliance
and system. Use of incompatible additives can
cause damage and will invalidate the appliance
guarantee.
Frost protection:
Use a suitable anti-freeze/inhibitor at the correct
strength to protect against freezing.
A frost themostat should be fitted to the system
where the system is most exposed and at risk of
freezing.
Sealed heating systems:
Where the appliance is fitted to a sealed heating
system your installer will inform you of the
minimum and maximum pressure which must be
indicated on the pressure gauge.
Regularly check the pressure is maintained and
contact your installer or maintenance engineer if
there is a noticeable, permanent drop in
pressure. If the system loses pressure it should
be repressurised and the cause of the loss
investigated.
Pressure gauge
on the Camray
Utility System
model.

GENERAL INFORMATION
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
5
INTRODUCTION
Conventional flued appliances:
Minimum area of of air inlet for combustion:
Model Area (cm2)
12/18 72
18/25 110
25/32 138
GENERAL INFORMATION
BOILER LOCATION:
This boiler is only suitable for installing internally
within a property at a suitable location onto a
fixed rigid surface at least the same size as the
boiler and capable of supporting the boiler
weight.
The boiler is not suitable for external installation
unless a suitable enclosure is provided.
Roof space installations must fully conform to
BS 5410 part 1 section 4.6.9.
** The boiler can be installed under a worktop
as long as:
4The worktop above the boiler is removable
for maintenance.
4There is at least 10mm clearance above the
boiler.
4The front of the boiler is not enclosed.
VENTILATION:
Air vents must be functional at all times and the
air supply must not be restricted or
contaminated.
The appliance clearances must meet the
minimum shown opposite for servicing and
venting purposes.
* If this clearance is less than 75mm the flue
'knock-out' panel sections must be removed to
improve air circulation and cooling.
Do not place clothes or objects to hinder the air
circulation required by the appliance.
Conventional flue appliances require an
adequate supply of fresh air which must be
delivered to the boiler for combustion purposes
through a permanent inlet, such as an air brick,
into the area where the boiler is situated.
600mm
300mm**
5mm*
5mm*
380mm
1200mm
1155mm

GENERAL INFORMATION GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
6
INTRODUCTION
GENERAL INFORMATION
If a cupboard or compartment which is to be
used for storage or airing is built around the
appliance after installation there must be a
non-combustible partition around the boiler.
Further information can be found in BS 5410
which also describes venting requirements.
Venting compartments:
4Ventilation must be provided for boilers fitted
into compartments as described in BS 5410
4A minimum of 2 air vents must be fitted, one
at low level and another at high level onto
the same wall using the same air for
circulation.
4Combustion air must not be taken from a
room or internal space containing a bath or
shower and must not communicate with a
protected area such as a hall, stairway,
landing, corridor, lobby, shaft etc.
4Air vents must allow access for clean free air
and must be sited to comply with the flue
terminal position requirements.
4Air ducting runs must not exceed 3m.
4Low level air vents must be less than
450mm from the floor.
4A warning label must be added to the vents
with a statement to the effect: ''Do not block
this vent. Do not use for storage”.
MINIMUM AIR VENT AREA (cm2) FOR
APPLIANCES INSTALLED IN A COMPARTMENT:
1Internal air to and from a space/room inside the building.
2External air to and from directly outside the building.
Conventional flue:
Room Sealed flue:
Model
12/18
18/25
25/32
Model
12/18
18/25
25/32
Internal1ventilation External2 ventilation
High
Level
Low
Level
High
Level
Low
Level
Internal1ventilation External2 ventilation
High
Level
Low
Level
High
Level
Low
Level
143 215 72 143
220 330 110 220
275 413 138 275
143 143 72 72
220 220 110 110
275275138 138

CONTROLS
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
A Temperature control.
B Reset button - burner lock-out indicator/reset
button (on the burner control box behind
the front panel).
C Reset button - boiler overheat thermostat
(behind front panel).
D Reset button - flue overheat thermostat
(behind front panel).
E Front panel.
CONTROLS
USING YOUR
APPLIANCE
CA D
UTILITY & UTILITY SYSTEM MODELS:
E
B
7

OPERATING THE APPLIANCE GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
USING YOUR
APPLIANCE
OPERATING THE APPLIANCE
SWITCHING THE BOILER ON/OFF:
4To switch on the boiler; turn ON the water,
oil and electricity supply to the boiler.
4Check the programmer/timer is correct and
it is set to ON.
4Set the room thermostat to the desired
setting.
4Open and set thermostatic radiator valves as
required.
4Turn the boiler water temperature control to
the required setting.
4To switch off the boiler; turn the
programmer/timer to OFF for heating and
hot water. If the appliance is left unused and
exposed to freezing conditions; shut off all
the mains supplies, isolate the boiler and
drain the system and boiler.
SETTING HEATING TEMPERATURE:
4Turn the control clockwise to increase the
radiator temperature.
4Turn the control anti-clockwise to reduce the
radiator temperature.
The minimum and maximum ranges of the
heating control positions are approx. 55°C to
81°C.
CONTROLLING CENTRAL HEATING:
4Set the programmer/timer to the correct time
with the required ON/OFF periods.
4Turn the room thermostat to the temperature
required.
4Set thermostatic radiator valves to the
required temperature for each room.
TEMPERATURE CONTROL:
8

OPERATING THE APPLIANCE
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
9
OPERATING THE APPLIANCE
FAULT CONDITIONS:
The burner lockout indicator/reset button can
indicate some basic faults:
Normal operation:
a) Lockout indicator OFF:
The burner will cycle on and off under the control
of the programmer/timer and the thermostats.
Lockout indicator light:
b) Light ON, boiler not firing:
1. Check oil level in the oil storage tank.
2. Press button (B). Boiler should fire.
3. If no response, wait 2 minutes - press
reset button (B) again.
4. If lockout light stays on, do not attempt
further resets. Contact your service
engineer for advice.
c) Light OFF, boiler not on, no heating/hot
water:
1. Ensure there is a power supply to the boiler.
2. Check the programmer is set to ON for
heating.
3. Check the setting of the room thermostat,
boiler temperature control/tank thermostat.
4. Press reset buttons (C and D).
5. If the boiler stays off contact your service
engineer for advice.
CD
B
a), c)
b)
USING YOUR
APPLIANCE
CD
B
CD
B

TIPS ON ENERGY SAVING
Heating economically:
The boiler is designed to provide a high level of
comfort while keeping oil consumption and the
resulting environmental effect as low as possible.
The temperature control on the boiler should be
set as low as possible while still maintaining a
comfortable room temperature.
The temperature of each room can be set
individually using the thermostatic radiator valves
(except the primary room with the room
thermostat).
Roof insulation:
Around 30% of the heat loss from a property is
through the roof. Replace any old insulation with
new insulation, preferably to a minimum
thickness of 200mm.
Window frames:
Single glazed windows, particularly those with
steel frames, can lose a great deal of heat.
Consideration should be given to replacement
with PVCu or wooden framed double glazed
units.
Curtains:
Lined curtains, or heavier full length curtains can
provide excellent insulation. However, always
ensure that the curtains do not drape over
radiators.
Draughts:
Try to ensure that draughts around doors,
windows, letterboxes and keyholes etc., are
reduced by using a suitable draught excluder.
Warning: do not block or seal any air vents
that are installed to ensure the central
heating boiler (or other appliance) operate
safely.
TIPS ON ENERGY SAVING GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
10
ENERGY
SAVING

TIPS ON ENERGY SAVING
Room thermostats:
Reducing the setting of the room thermostat by
1°C can reduce fuel consumption by up to 10%.
New control systems:
Upgrade your heating control system with the
latest equipment available. The minimum level of
control for a heating system is a
programmer/timer, interlocking room thermostat
and thermostatic radiator valves.
Radiators:
More often than not radiators will be sited
underneath a window, so the warm air from the
radiator heats the colder incoming air from the
window.
The performance of the radiator will be affected
if the curtains are allowed to drape over the
radiator or shelves are fitted above it.
The positioning of furniture and tables in front of
the radiator should also be avoided.
It is advisable to manually adjust all radiator
valves every 2-3 months to prevent them from
sticking. It is also important that the plastic tops
of all valves are always in position and not
cracked or damaged to help prevent accidents.
Care should be taken when vacuum cleaning
carpets to avoid damage to valves and pipework.
The heating system and the outputs of the
radiators have been carefully selected by your
installer. The temperature obtainable in any given
room is dependent on all radiators being
operated at the same time. If you decide to turn
off radiators in unused rooms, spare bedrooms
etc., you may experience slightly lower room
temperatures in rooms adjacent to unheated
rooms.
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
11
TIPS ON ENERGY SAVING
ENERGY
SAVING

MAINTAINING YOUR APPLIANCE
Your new appliance represents a long term
investment in a reliable, high quality product.
In order to realise its maximum working life and
to ensure it continues to operate at peak
efficiency and performance, it is essential that
servicing and maintenance checks are performed
at least once a year by a competent person.
If you would like to know more about servicing
options from Worcester, Bosch Group please
visit www.worcester-bosch.co.uk.
Please tick the appropriate box on your warranty
registration card for further details on the
Worcester, Bosch Group service contract.
In addition to the service contract we are
pleased to offer a one-off annual service or
breakdown cover.
When your appliance requires servicing please
contact the Worcester, Bosch Group contact
centre (see inside front cover for details).
Maintenance tips:
Regularly check the oil level in the tank.
Regularly check the system pressure, ask your
installer for guidance.
Do not obstruct the flue outlet or the air inlet.
MAINTAINING YOUR
APPLIANCE
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
12
MAINTENANCE

FAULT FINDING
Problem Cause Remedy
Switch off appliance at
master switch, wait a few
seconds then switch on
again
Check setting
Check programmer
settings
Check setting
Desired room temperature
is not reached
Thermostatic radiator
valve(s) set too low
Room thermostat set too Increase room thermostat
low setting
Temperature control for
flow on boiler set too
low
Air trapped in heating
system
Desired room temperature
exceeded by large amount
Temperature rises instead
of falling
No display or display unit
does not respond
Hot water temperature too
low
Radiators are too hot
Clock is incorrectly set
Momentary power failure
Hot water tank
temperature set too low
Hot water not in timed
period on the programmer
Temperature control on
boiler set too low
Increase thermostatic
radiator valve setting(s)
Increase
temperature control
setting
Bleed radiators, if fitted to
a sealed system recharge
heating system
Turn down thermostatic
radiator valves / room stat
Check setting
FAULT FINDING
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
13
MAINTENANCE

circumstances this will be from 1 to 3 working
days (excluding weekends) for priority
breakdown situations (no hot water and/or
heating).
Invoices for attendance and repair work carried
out on this appliance by any third party will not
be accepted.
Utility and Utility System models:
APPLIANCE DATA LABEL
The data label can be found on the inside of the
right hand side panel.
To access first remove the front panel:
4Gently pull front panel to release lugs and
remove from appliance.
To replace front panel:
4Gently push the panel in to place (from the
edges so as not to damage the panel) until
the studs locate in their connectors.
Utility shown.
FAULT OR BREAKDOWN
This appliance is supported in the UK by
Worcester, Bosch Group, part of BBT
Thermotechnology UK Ltd.
Specialist factory trained Service Engineers are
available to attend in the unlikely event that a
breakdown occurs on this appliance.
No charge will be made for parts and/or
labour providing:
4An appliance fault is found and the
appliance has been installed within the past
24 months
4Reasonable evidence of this must be
supplied on request
4A call-out charge will be made where:
4The appliance has been installed for over 24
months OR
4Our Field Service Engineer finds no fault
with the appliance (see Note). OR
4Evidence cannot be provided that the first
year service inspection has been carried out.
(i.e. an entry in the service interval record
found at the rear of the appliance installation
and servicing manual). OR
4The cause of breakdown is misuse or with
other parts of your plumbing/heating system,
or with equipment not supplied by BBT
Thermotechnology UK Ltd.
Note: NO APPLIANCE FAULT IS FOUND ON
OVER 30% OF ALL SERVICE CALL OUTS.
Please read this guide carefully to gain a good
understanding of the operation of your appliance.
In the case of a suspected fault, refer to the fault
finding section of this guide.
If in doubt contact Worcester, Bosch Group
quoting the boiler serial and model number.
These numbers are printed on a Data Label
which is located as shown opposite. (You can
record this information on the inside back cover
of this manual.)
In the unlikely event of an appliance fault or
breakdown please call the contact centre (see
inside front cover for details). Your service
administrator will arrange for an Engineer to call
with the minimum of delay. Under normal
Kitchen models:
APPLIANCE
DATA LABEL
DATA LABEL
FAULT OR BREAKDOWN GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
14
MAINTENANCE

YOUR GUARANTEE
This appliance is guaranteed against faulty
materials or workmanship for a period of 24
calendar months (60 months for the primary heat
exchanger) from the date of installation subject
to the following conditions:
4That during the period of this guarantee any
components of the unit which are proved to
be faulty or defective in manufacture will be
exchanged or repaired free of material
charges and free of labour charges if
repaired directly by BBT Thermotechnology
UK Ltd. Invoices for attendance and repair of
this appliance by third parties will not be
accepted for payment by BBT
Thermotechnology UK Ltd.
4That the householder may be asked to prove
the date of installation, that the appliance
was correctly commissioned and that the 12
month service has been carried out to the
satisfaction of BBT Thermotechnology UK
Ltd, when requested. The guarantee card
must then be returned within 30 days of
installation.
4That any product or part thereof returned for
servicing under the guarantee must be
accompanied by a claim stating the Model,
Serial Number and Date of Installation.
4That BBT Thermotechnology UK Ltd will not
accept responsibility for damage caused by
faulty installation, neglect, misuse,
accidental damage or non-observance of
the instructions contained in the Installation
and Users Instructions leaflets.
4That the appliance has been used only for
normal domestic purposes, for which it was
designed.
4That this guarantee applies only to
equipment purchased and used in mainland
Great Britain.
This guarantee is given in addition to all your
normal statutory rights.
Worcester, Bosch Group is a trading name of
BBT Thermotechnology UK Ltd.
YOUR GUARANTEE
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
15
GUARANTEE

Model
Serial No.
(See identity label inside appliance casing)
Type / size
Date of installation
Installer details
GUARANTEE REGISTRATION
You should complete and return the postpaid
Guarantee Registration Card within 30 days of
installation.
Returning your card will register you as the
owner of your new appliance and will assist us in
maintaining an effective and efficient customer
service by establishing a reference and
permanent record for your boiler.
This does not affect your statutory rights.
For your own record:
GUARANTEE
REGISTRATION
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
16
GUARANTEE

NOTES
NOTES
NOTES
GREENSTAR CAMRAY UTILITY/UTILITY SYSTEM 12/18 - 18/25 - 25/32
8 716 111 983a (02.07)
17
NOTES

USER INSTRUCTIONS &
CUSTOMER CARE GUIDE
EXCELLENCE COMES AS STANDARD
Worcester, Bosch Group
Cotswold Way, Warndon, Worcester WR4 9SW.
T
el. 01905 754624 Fax. [phone]
www.worcester-bosch.co.uk
Worcester, Bosch Group is a brand name of BBT Thermotechnology UK Ltd.
8 716 111 983a (02.07)