Bosch WQB246DAFG User manual

Tumble dryer
WQB246DAFG
[en] Instructions for use and
assembly
Translated from German to English - www.onlinedoctranslator.com

de
Further information and explanations can be
found online:
Table of contents
1 Security ................................... 4
1.1 General information .................... 4
8 Dry target ................................ 28
8.1 Changing the drying target................... 28
8.2 Adjust drying target ............. 281.2 Intended
use ........................................... 4
1.3 Restriction of the user
group ........................................... 4
9 programs ................................ 29
9.1 Automatic programs.............. 29
9.2 Time programs................................ 31
1.4 Safe installation ....................5
1.5 Safe use .................... 7 10 Accessories ................................... 32
1.6 Safe cleaning and
maintenance ........................................... 10 11 Laundry ................................... 33
11.1 Preparing laundry ............33
2 Avoid material damage .......... 11
12 Basic operation......33
12.1 Switching on the device .................... 33
12.2 Setting the program ............. 33
3 Environmental protection and saving ....... 11
3.1 Dispose of packaging............11
3.2 Saving energy ....................... 11
3.3 Energy saving mode .................... 12 12.3 Adjusting program
settings................................. 33
4 Setting up and connecting ..... 12
4.1 Unpacking the device.................... 12
4.2 Scope of delivery................................. 12
12.4 Saving program
settings................................. 34
12.5 Loading laundry................... 34
12.6 Start the program................. 34
12.7 Adding laundry................ 34
12.8 Cancel program ........... 34
12.9 Removing laundry ............34
4.3 Requirements for the installation
site ........................................... 13
4.4 Water drain hose ............ 13
4.5 Aligning the device................................ 16
4.6 Changing the door stop .......... 16
4.7 Connect the device electrically... 19
12.10 Put the device into standby
mode
zen .......................................... 35
5 Getting to know each other .......................... 20
5.1 Device.................................................. 20
5.2 Control panel ................................. 21
5.3 Operating logic................................ 21
12.11 Lint filter ........................... 35
12.12 Condensation water container...... 36
13 Parental Control .......................... 37
13.1 Activate parental controls... 37
6 Display .......................................... 22
7 buttons .......................................... 24
13.2 Deactivating parental
controls................................................. 37
14 Home Connect .......................... 38
14.1 Setting up the Home Connect
app................................................ 38
2

de
14.2 Setting up Home Connect ..... 38
14.3 Home Connect menu ............ 38
14.4 Activate Wi-Fi on the device ...... 39
14.5 Deactivate Wi-Fi on the device .. 39
22 Technical data ................... 56
23 Declaration of Conformity ...........57
14.6 Resetting the network settings of
the device................. 39
14.7 Remote start .......................... 39
14.8 Intelligent program
recommendation................................. 40
14.9 Remote diagnosis .......................... 40
14.10 Data protection................................. 40
15 Basic settings ................ 42
15.1 Overview of the basic
settings ........................... 42
15.2 Changing basic settings... 43
16 Device care .......................... 43
16.1 Preparing for device care....... 43
16.2 Calling up device care ........... 43
16.3 Carry out simple device
maintenance ........................... 44
16.4 Carry out intensive device
care ........................... 44
17 Cleaning and care ............. 45
17.1 Tips for cleaning and
care .................................... 45
17.2 Humidity sensor ................46
17.3 Filter of the condensation water
container................................. 46
18 Troubleshooting ................... 48
19 Transport, storage and
Dispose of ................................ 53
19.1 Preparing the device for
transport................................. 53
19.2 Dispose of old device................... 53
20 Customer service .......................... 54
20.1 Product number (E-No.),
production number (FD)
and counting number (Z-No.)........ 54
21 Consumption values .................... 55
3

deSecurity
1 Security
Please note the following safety instructions.
1.1 General information
¡Read these instructions carefully.
¡Save the instructions and product information
later use or subsequent ownership.
¡Do not connect the device if it is damaged during transport.
1.2 Intended use
Use the device only:
¡to tumble dry textiles that have been washed with water
dry and refresh.
¡in private households and in closed rooms of the home
chen environment.
¡up to an altitude of 4000 m above sea level.
1.3 Restriction of the user group
This device can be used by children aged 8 years and over and by
people with reduced physical, sensory or mental capabilities or lack
of experience and/or knowledge, if they are supervised or
instructed in the safe use of the device and understand the
resulting dangers have.
Children are not allowed to play with the device.
Cleaning and user maintenance must not be carried out by
children without supervision.
Keep children under 3 years and pets away from the device.
4

Securityde
1.4 Safe Installation
WARNING - Risk of electric shock!
Improper installations are dangerous.
▶Only connect and operate the device in accordance with the
information on the nameplate.
▶Only connect the device to an alternating current power supply
via a properly installed earthed socket.
▶The protective conductor system of the electrical house
installation must be installed correctly. The installation must
have a sufficiently large cable cross-section.
▶When using a residual current circuit breaker, only use a type
with the symbol.
▶Never power the device via an external switching device,
e.g. B. timer or remote control.
▶Never connect the device to a circuit that is regularly switched
on and off by the energy supplier.
▶When the device is installed, the mains plug of the mains
connection cable must be freely accessible, or if free access is not
possible, an all-pole disconnecting device must be installed in the
fixed electrical installation in accordance with the installation
regulations.
▶When setting up the device, ensure that the power cable is
not pinched or damaged.
Damaged insulation of the mains connection cable is dangerous.
▶Never bring the power cord into contact with hot parts of the
device or heat sources.
▶Never bring the power cord into contact with sharp points or
edges.
▶Never bend, squeeze or change the power cable.
5

deSecurity
WARNING - Danger of fire!
Using an extended power cord and unauthorized adapters is
dangerous.
▶Do not use extension cables or multiple socket strips.
▶Only use adapters and power cables approved by the
manufacturer.
▶If the mains connection cable is too short and a longer mains
connection cable is not available, contact a specialist electrician
to adapt the house installation.
WARNING - Risk of injury!
The heavy weight of the device can lead to injuries when lifting
it.
▶Do not lift the device alone.
If this appliance is installed improperly in a washer-dryer column,
the installed appliance may fall.
▶Only stack the dryer on a washing machine using the dryer
manufacturer's connection kit
→ "Accessories", page 32 . Any other installation method is not
permitted.
▶Do not install the device in a washer-dryer column if the dryer
manufacturer does not offer a suitable connection kit.
▶Do not install devices from different manufacturers and with
different depths and widths in a washer-dryer column.
▶Do not place a washer-dryer column on a platform as the devices
can tip over.
WARNING - Danger of suffocation!
Children can pull packaging material over their heads or wrap
themselves in it and suffocate.
▶Keep packaging material away from children.
▶Do not let children play with packaging materials.
6

Securityde
CAUTION - Danger of injury!
The device may vibrate or move during operation.
▶Place the device on a clean, flat and firm surface.
▶Align the device using the device feet and a spirit level.
There is a risk of tripping if hoses and power cables are installed
incorrectly.
▶Lay the hoses and power cables so that there is no risk of
tripping.
If the device is moved on protruding components, such as: B. the
appliance door, the parts can break off.
▶Do not move the device on protruding components.
CAUTION - Danger of cutting!
Sharp edges on the device can cause cuts if touched.
▶Do not touch the device on sharp edges.
▶Use protective gloves when installing and transporting the
device.
1.5 Safe use
WARNING - Risk of electric shock!
A damaged device or a damaged power cable is dangerous.
▶Never operate a damaged device.
▶Never pull on the power cord to disconnect the device from the
power supply. Always pull on the mains plug of the mains
connection cable.
▶If the device or the mains connection cable is damaged,
immediately pull out the mains plug of the mains connection
cable or switch off the fuse in the fuse box.
▶Call customer service. → Page 54
Penetrating moisture can cause an electric shock.
▶Only use the device in closed rooms.
▶Never expose the device to extreme heat or moisture.
7

deSecurity
▶Do not use steam cleaners, high-pressure cleaners, hoses or
showers to clean the device.
WARNING - Danger of damage to health!
Children can become trapped in the device and endanger their
lives.
▶Do not place the device behind a door that blocks or prevents
the device door from opening.
▶For old devices, pull the power plug of the power connection
cable, then cut the power connection cable and destroy the lock
on the device door to such an extent that the device door no
longer closes.
WARNING - Danger of suffocation!
Children can inhale or swallow small parts and thereby
suffocate.
▶Keep small parts away from children.
▶Do not let children play with small parts.
WARNING - Danger of explosion!
Coal dust or flour in the area around the device can cause an
explosion.
▶Keep the area around the device clean during operation.
WARNING - Danger of poisoning!
The condensation from this device is not potable and may be
contaminated with lint.
▶Do not drink or reuse the condensation water from the
device.
Detergents and care products can cause poisoning if consumed.
▶If accidentally swallowed, seek medical advice.
▶Keep detergents and care products out of the reach of children.
8th

Securityde
WARNING - Danger of fire!
The refrigerant R290 in this device is environmentally friendly but
flammable and can ignite if it comes into contact with open flames or
ignition sources.
▶Keep open flames and ignition sources away from the device.
WARNING - Danger of explosion!
Residue in the lint filter can ignite when drying.
▶Clean the lint filter regularly.
Easily flammable items, such as lighters or matches, can catch fire
when dry.
▶Before drying, remove all highly flammable items from the
laundry bags.
If unwashed laundry has been in contact with solvents, oil, wax,
wax remover, paint, grease or stain remover, it may ignite when
dried.
▶Do not dry unwashed laundry in this appliance.
▶Rinse laundry thoroughly with hot water and detergent before
drying.
▶Do not use the device if the laundry has previously been cleaned
with industrial chemicals.
WARNING - Danger of fire!
If the drying stops prematurely, the laundry will not be sufficiently
cooled and may catch fire.
▶Do not stop the drying program prematurely.
▶If the drying stops prematurely, remove the laundry immediately
and spread it out.
CAUTION - Danger of injury!
If you step on or climb onto the device, the cover plate may break.
▶Do not step or climb on the device.
If you sit or lean on the open door, the device may tip over.
▶Do not sit or lean on the appliance door.
9

deSecurity
▶Do not place objects on the appliance door.
Interfering with the rotating drum can cause injury to your
hands.
▶Before taking action, wait for the drum to come to a complete
standstill.
1.6 Safe cleaning and maintenance
WARNING - Risk of electric shock!
Improper repairs are dangerous.
▶Never make any technical changes to the device or the characteristics of the
device.
▶Only trained specialist personnel may carry out repairs on the
device.
▶Only original spare parts may be used to repair the device.
▶If the power cord of this device is damaged, it must be replaced
by the manufacturer or its customer service or a similarly
qualified person to avoid hazards.
Penetrating moisture can cause an electric shock.
▶Do not use steam cleaners, high-pressure cleaners, hoses or
showers to clean the device.
WARNING - Risk of injury!
Using non-original spare parts and accessories is dangerous.
▶Only use original replacement lines and original accessories from the
manufacturer.
WARNING - Danger of poisoning!
When using cleaning agents that contain solvents, toxic fumes can
be created.
▶Do not use cleaning agents containing solvents.
10

Avoid property damagede
S2
avoid damage to the vehicle ▶Clean the device only with water
and a soft, damp cloth.
▶If you come into contact with the device,
immediately remove any detergent
residue, spray mist or residue.
Avoid material damage
the
Avoid property damage
DANGER!
Incorrect dosing of fabric softeners,
detergents, care products and
cleaning agents can impair the
function of the device.
▶Follow the manufacturer’s dosage
recommendations.
Exceeding the maximum load
capacity will affect the device
function.
▶Observe the maximum load capacity
for each program and do not
exceed it.
→ "Programs", page 29
Overheating the device can affect
device functionality.
▶Keep the ventilation opening on the
device clear during operation.
▶Ensure adequate ventilation in
the room.
Light objects, such as hair and lint,
can be sucked into the device's
ventilation opening during operation
and affect device function.
▶Keep the area around the device
clean during operation.
▶Keep light objects away from the
device.
Foam or foam rubber may deform or
melt as it dries.
▶Do not dry laundry containing
foam or foam rubber.
Unsuitable cleaning agents can
damage the surfaces of the device.
▶Do not use harsh or abrasive
cleaning agents.
▶Do not use cleaning agents that
contain strong alcohol content.
▶Do not use hard scouring pads or
cleaning sponges.
U3 environmental protection and
Save
environmental protection and saving
Environmental protection and saving
3.1 Dispose of packaging
The packaging materials are
environmentally friendly and recyclable.
▶Dispose of the individual components
separately according to type.
3.2 Save energy
If you follow these instructions, your
device will use less power.
Operate the device in a well-ventilated
room and keep the device's ventilation
opening clear.
aImpaired air exchange
extends the program duration and
increases energy consumption.
Before drying, spin the laundry in
the washing machine.
aMoister laundry prolongs this
program duration and increases
energy consumption.
Adhere to the maximum load capacity
of the programs.
→ "Programs", page 29
aExceeding the maximum
Load size extends the program
duration and increases energy
consumption.
11

deSetting up and connecting
After drying, clean the lint filter →
Page 35 .
→ "Dispose of packaging",
page 11
aA contaminated lint filter at least
alters the air flow in the device,
extends the program duration and
increases energy consumption.
2.Check the device for visible damage.
3.Open the door.
4.Remove the accessories from the
drum.
Disable unused Wi-Fi.
→ "Deactivate Wi-Fi on the device",
page 39 .
5.Close the door.
4.2 Scope of delivery
aActivated Wi-Fi increases the energy
energy consumption. After unpacking, check all parts for
transport damage and that the
delivery is complete.
3.3 Energy saving mode DANGER!
Operation with incomplete or
defective accessories can impair the
device function or lead to property
damage and device damage.
▶Do not operate the device with
incomplete or defective
accessories.
▶Replace relevant accessories before
operating the device.
→ "Accessories", page 32
If you do not use the device for a long
time, it automatically switches to
energy saving mode. All displays go
out and
flashes.
The energy saving mode is ended by
operating the device again.
If you continue not to operate the
device, it automatically switches to
standby mode.
scope of delivery Description
Tumble dryer
A4 Set up and
Connect
set up and connect
Setting up and connecting
4.1 Unpack the device
DANGER!
Objects left in the drum that are not
intended to operate in the device can
cause property damage and damage
to the device.
▶Remove these items and included
accessories from the drum before
operation.
Supporting documents
water drain
hose with connection
terminal adapter,
fastening
material and curved
mer.
→ "water drain
hose",
Page 13
1.Packaging material and protective
completely removed from the devicecovers ko
nen.
12

Setting up and connecting de
4.3 Requirements for the
installation location
Installation location Requirements
In a laundry
Dry column
This device only
with the original
len connection
set of drying
manufacturer in
a washing dryer
cken column on
place.
¡connection
set with
pullable arm
work plate
→ Page 32
¡connection
sentence
→ Page 32
DANGER!
If the device is tilted beyond 40°,
residual water in the device may leak
and cause property damage.
▶Tilt the device carefully.
▶Transport the device standing up.
Freezing residual water in the device
can lead to device damage.
▶Do not set up and operate the
device in areas at risk of frost or
outdoors.
If the device is operated immediately
after transport, the coolant contained
in the device can cause damage to the
device.
▶Immediately after transport, let the
device rest for two hours before
putting it into operation.
This device only
on a washing machine
machine from
same manufacturer
lers. The
Depth and breadth
of this device
have to with the
Dimensions
the washing machine
machine match
voices.
The washing dryer
cken column not
on a pedestal
place.
Installation location Requirements
On the footboard
the
Place the device on a
clean, level surface
place on a solid
surface.
Turn off the device
judge
→ Page 16 .
On a wall No hoses
and mains connection
final line
between wall
and device on
clamp.
4.4 Water drain hose
During drying, condensation is
created, which your device collects in
the condensation container at the
factory. Use the water
13

deSetting up and connecting
water drain hose to drain excess
condensation water directly into the
wastewater.
1.Pull the condensation water hose from
the connector.
Hints
¡Operate this device with
the included water drain hose.
→ "Connecting the water drain
hose", page 14
If you connect the water drain hose,
you do not have to regularly empty
the condensation water container.
→ "Empty the condensation water
container", page 37
¡You can do this optional
→ "Accessories", page 32 order from
customer service.
The condensation water hose is
connected to the nozzle at the
factory.
A notice:When removing the
condensation hose, liquid may
escape from the connector.
Water drain hose
connect 2.Slide the condensation water hose
onto the holder.
If you do not want to empty the
device's condensation container
regularly, connect the water drain
hose.
DANGER!
If the device is operated without a
properly connected condensation
water hose or water drain hose, liquid
may escape from the nozzle.
▶Before operating the device,
properly connect the condensation
water hose or the water drain hose
to the connector.
requirements
¡The device and accessories are
unpacked.
→ "Unpacking the device", page 12
¡The device is installed at the installation location
provides.
→ "Requirements for the installation
location", page 13
14

Setting up and connectingde
3.Push the water drain hose onto
the connector as far as it will
go.
6.Insert the plug into the hollow
on the top.
7.Push in the condensation water
container → Page 37 .
4.Empty the condensation water
container → Page 37 .8th.Connect the device to the water
drain.
→ "Water drain connection types",
page 15
Tip:To collect the condensation water
again in the condensation water
container, e.g. If you change the
location of the device, for example,
undo these steps in reverse order.
Water drain connection types
5.Remove the bottom plug. DANGER!
If the drain is clogged or blocked,
backed-up wastewater can flow back
into the device.
▶Before operating the device, ensure
that wastewater drains quickly and
clear any blockages.
process into one
Siphon.
The connection
place with one
Hose clamp
(12-22 mm)
chern.
The water drain
running hose with
a hose
leadership in mini
15

de Setting up and connecting
times 80 cm and
maximum 100 cm
Fix height.
4.5 Align the device
To reduce noise and vibration, align
the device correctly.
▶To align the device, turn the
device feet. Check the alignment
with a spirit level.
A notice:With
the Y distributor
→ Page 32 can-
name that one
water drain
hose one
additional equipment
advices such as B. a
washing machine
machine at the same time
chen process of the
siphons on
close.
expiration in one
Bathroom sink.
The water drain
running hose
completely through
the manifold
→ page 12 push
and with that
fastening
fix material.
The manifold in
maximum 100 cm
Fix height.
All device feet must be firmly on
the floor.
4.6 Changing the door stop
To make it easier to insert and remove
laundry, you can change the door stop.
process into one
Gully.
The water drain
running hose
completely through
the manifold
→ page 12 push
and with that
fastening
fix material.
The manifold
attach to the gully
gene.
CAUTION
Danger of cutting!
Sharp edges on the device can
cause cuts if touched.
▶Do not touch the device on sharp
edges.
▶Use protective gloves when
installing and transporting the
device.
Hints
¡Use to remove and
Only use a Torx T15 screwdriver and
a Torx T20 screwdriver when
inserting screws.
16

Setting up and connectingde
¡Place the removed door on a
a flat and soft surface to avoid
material damage.
2.Unscrew the door hinge and door
hook.
Remove door
Requirement:The device is disconnected
from the mains.
1.Open the door.
2.Unscrew the door.
3.Screw the door hinge and door
hook on opposite sides.
Change door hinge and door
hook
1.Unscrew the door hinge cover.
Make sure not to pinch or
damage the door seal.
17

deSetting up and connecting
4.Screw on the door hinge cover. Change door lock
1.Unscrew the door lock cover.
Make sure not to pinch or
damage the door seal. 2.Remove the door lock.
5.Remove the colored door handle
indicator and replace it with the
cover on the opposite side.
3.Insert the door lock on the opposite
side.
Select the position of the door handle
indicator depending on the location of the
device:
– The device is placed on the floor.
– The device is positioned elevated
in a washing and drying column.
18

Setting up and connectingde
4.Screw on the door lock cover.
5.Screw on the door.
4.7 Connect the device
electrically
1.Plug the power plug of the device's
power cord into a socket near the
device.
The connection data of the device can be found
which you can find in the technical data
→ Page 56 .
2.Check that the power plug is firmly
seated.
19

de Get to know
K5
learn to name
Get to know
Get to know
5.1 Device
Here you will find an overview of the components of your device.
5
4
3
2
1
Je
Shape.
n/aDepending on the device type, details in the picture may vary, e.g. B. Color and
1Ventilation opening
Lint filter → Page 35
door
4Condensation container
→ Page 36
25Control panel →
Page 21
3
20