Bosch FPC 7034 User manual
Fire Alarm Systems | FPC-7034 IDC expander, 4-point
FPC-7034 IDC expander, 4-point
www.boschsecurity.com
uAdds four Class B or two Class A initiating circuits
to the FPD‑7024 FACP
uFor use with normally‑open (NO) or normally‑closed
(NC) alarm contacts
uCompatible with two‑wire or four‑wire smoke
detectors
uUp to 20 two‑wire smoke detectors per circuit
uEasy installation due to plug‑in design and screw
terminal circuit connections
The FPC‑7034 Four-point Expander doubles the
number of alarm initiating device circuits on the
FPD‑7024 Fire Alarm Control Panel (FACP). These
circuits are identical to the circuits on the FACP.
This plug‑in module is automatically recognized by the
control panel's firmware when power is restored to
the system.
Certifications and approvals
Region Regulatory compliance/quality marks
USA UL UL 864, Control Units and Accessories
for Fire Alarm Systems
FM FPC-7034
CSFM see www.boschsecurity.com (the Bosch
website)
FDNY-
CoA 6173
Installation/configuration notes
Compatible Products
The FPC‑7034 is compatible with the FPD‑7024 FACPs.
For a list of compatible smoke detectors, see the FPD
7024 Smoke Detector Compatibility List Technogram.
Notice
When four‑wire smoke detectors are used, power
must be supplied to the detectors from either the
control panel or an external power source.
Mounting Considerations
The FPC‑7034 mounts on the FPD‑7024 control board,
just to the right of the keypad. Use the four nylon
stand‑offs supplied with the expander.
Initiating Circuit Wiring
Circuit connection for the expansion initiating circuits
is identical to the on‑board circuit configuration. For
wiring details, see the FPD‑7024 Installation Guide.
Install a supplied EOL resistor at the end of each
wiring run.
Parts included
Quantity Component
1 Four-loop expander board
4 2.21 kΩ End‑of‑Line (EOL) resistors (P/
N: 25899)
Quantity Component
4 Stand‑offs (P/N: 26510)
1 Literature pack
Technical specifications
Environmental Considerations
Environment: Indoor, dry
Relative Humidity: Up to 95%, non‑condensing
Temperature (operating): +32°F to +122°F (0°C to +50°C)
Mechanical Properties
Dimensions
(HxWxD):
2.0 in. x 4.5 in. x 1.3 in.
(5.1 cm x 11.4 cm x 3.3 cm)
Response Time: Choice of fast (500 ms) or programmable from
1 sec to 89 sec
Power Requirements
per initiating circuit:
Alarm Current (short circuit): 40 mA maximum
Alarm Current (threshold): >25 mA
Detector Standby Current (total): 3 mA maximum
Loop Supervision Current: 8.0 mA to 15.0 mA
Trouble Current Threshold: <7 mA
Voltage (supply): 18.0 VDC to 25.5 VDC
per FPC‑7034 module:
Current (standby): 60 mA maximum
Current (alarm): 160 mA maximum
Ordering information
FPC-7034 IDC expander, 4-point
The FPC‑7034 adds four Class B or two Class A
initiating circuits to the FPD‑7024 FACP. This plug‑in
module is automatically recognized by the control
panel's firmware when power is restored to the
system.
Order number FPC-7034
2| FPC-7034 IDC expander, 4-point
Represented by:
Europe, Middle East, Africa: Germany: North America: Asia-Pacific:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
emea.boschsecurity.com
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
www.boschsecurity.us
Robert Bosch (SEA) Pte Ltd, Security Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
www.boschsecurity.asia
© Bosch Security Systems 2018 | Data subject to change without notice
2692182923 | en, V10, 05. Dec 2018
Table of contents
Other Bosch Extender manuals
