Bosch NEV 400 LSN User manual

NEV 400 LSN Power supply
ISP‑NEV400‑120
en Installation manual

NEV 400 LSN Power
supply Table of contents | en 3
Bosch Security Systems B.V. 2019-11 | 04 | F.01U.309.346
Table of contents
1Safety 4
2Short information 7
3System overview 8
4Installation 10
4.1 Preparations 11
4.2 Removing the enclosure knockouts 12
4.3 Installing the tamper switch rail 13
4.4 Installing the enclosure 14
4.5 Installing the power supply and the AC terminal block 17
4.6 Installing the MAP accessory mounting plate 20
4.7 Installing a 12 V converter (optional) 22
4.8 Installing a SIV 28 fuse plate (optional) 24
4.9 Installing the EMIL expansion module 25
4.10 Installing a relay module (optional) 26
4.11 Installing the enclosure lockset 27
5Cabling 28
5.1 Cabling overview 29
5.2 Connecting the thermistor 30
5.3 Connecting the tamper switch 30
5.4 Connecting the EMIL expansion module to the power
supply
32
5.5 Connecting the auxiliary outputs 32
5.6 Connecting the LSN 33
6Initial set-up and programming 34
6.1 Initial set-up 34
6.2 Programming 36
7Troubleshooting 40
8Maintenance 41
9Technical data 42

4en | Safety NEV 400 LSN Power
supply
2019-11 | 04 | F.01U.309.346 Bosch Security Systems B.V.
1 Safety
Danger!
Battery
Injuries due to electric shock, fire or explosion are possible if
the battery is handled or connected incorrectly.
– Always handle the battery carefully and replace it carefully.
– Make sure that the grounding terminal is always connected
and that N, L or are connected correctly.
– Make sure to first disconnect the positive wire of the
battery when removing it from the system.
– Be careful when connecting the positive (red) wire and the
"BATT +" port of the system. Make sure not to short-circuit
with the "BATT +" port to prevent electric arc from
occurring.
Danger!
Electrostatic discharge
Injuries and damage of electronic components are possible due
to electrostatic discharge.
– Use antistatic wrist strap while working with the system.
Danger!
Electricity
Injuries due to electricity are possible if the system is not
operated correctly or if the system is opened or modified not
accordingly to this manual.
– To switch off the power, make sure to have a circuit
breaker available.
– Ensure that the system is switched off during the
installation, wiring and maintenance process.
– Only open or modify the system accordingly to this manual.
– Ensure to connect the system to the electric supply with a
protective grounding contact.

NEV 400 LSN Power
supply Safety | en 5
Bosch Security Systems B.V. 2019-11 | 04 | F.01U.309.346
– Only qualified installers/service personnel are allowed to
install and maintain this system.
Danger!
Electricity
Injuries due to electricity are possible if the system is not
grounded correctly.
– Ensure to ground the system correctly.
– When installing the AC terminal block ensure to connect
the ground wire to the ground connection point of the
enclosure back wall.
Danger!
Electricity
Injuries and damage of the system due to wrong polarity and
short circuits are possible.
When connecting wires and cables, ensure to use the correct
polarity.
!
Caution!
Battery
Damage or contamination of the system is possible if the
battery is not handled correctly or if the battery is not replaced
on a regular basis.
– Only use a non-spillable battery.
– Place a label with the last replacement date on the battery.
– Under normal conditions of use, replace the battery every
3-5 years.
– Recycle the battery after replacement according to local
regulations.
!
Caution!
Installation
Damage or malfunction of the system is possible if the system
is not mounted and installed correctly.

6en | Safety NEV 400 LSN Power
supply
2019-11 | 04 | F.01U.309.346 Bosch Security Systems B.V.
– Place the system inside the monitored area on a stable
surface.
– Once the system is tested and ready to use, secure the
enclosure door with screws.
!
Caution!
Maintenance
Damage or malfunction of the system is possible if it is not
maintained on a regular basis.
– Ensure to get the system maintained once a year.
– Only qualified installers/service personnel are allowed to
maintain this system.
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable
must be collected separately and sent for environmentally
compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use
the return and collection systems put in place in the country
concerned.

NEV 400 LSN Power
supply Short information | en 7
Bosch Security Systems B.V. 2019-11 | 04 | F.01U.309.346
2 Short information
The NEV 400 LSN provides a remote power supply and is
installed offside a control panel. Trouble and tamper events are
transmitted via LSN (local security network).
This manual contains information on how to install the NEV 400
LSN. It describes the main steps required for cabling and
programming the system. Detailed information on the single
components can be found in the correspondent datasheets and
installation manuals.

8en | System overview NEV 400 LSN Power
supply
2019-11 | 04 | F.01U.309.346 Bosch Security Systems B.V.
3 System overview
The NEV 400 LSN contains the following components:
1 2 3
4
5
6
7
8
9
10
11
Figure3.1: NEV 400 LSN system overview
Element Description
1 ICP-MAP0120 expansion enclosure
2 ISP-PCBA-EMIL
3 IMS-RM relay module (optional)
4 ICP-MAP0021 accessory mounting plate EMIL
5 SIV 28 fuse plate (mounted on ICP-MAP0020
accessory mounting plate)
6 Tamper switch rail

NEV 400 LSN Power
supply System overview | en 9
Bosch Security Systems B.V. 2019-11 | 04 | F.01U.309.346
Element Description
7 ICP-MAP0055 expansion enclosure tamper
switch
8 Thermistor
9 Batteries
10 IPP-MAP0005-2 MAP power supply 28V/150W
11 AC terminal block

10 en | Installation NEV 400 LSN Power
supply
2019-11 | 04 | F.01U.309.346 Bosch Security Systems B.V.
4 Installation
This chapter contains information on how to install the
components of the NEV 400 LSN.
Danger!
Electrostatic discharge
Injuries and damage of electronic components are possible due
to electrostatic discharge.
– Use antistatic wrist strap while working with the system.
!
Caution!
Installation
Damage or malfunction of the system is possible if the system
is not mounted and installed correctly.
– Place the system inside the monitored area on a stable
surface.
– Once the system is tested and ready to use, secure the
enclosure door with screws.