Bosch 1613 User manual

1613
0 601 613 0 . .
1614
0 601 614 0 . .
1613EVS
0 601 613 7 . .
1614EVS
0 601 614 7 . .
Before use - Read this instruction manual.
Lisez attentivement la présente notice avant l'emploi.
Lea estas instrucciones de manejo antes de la utilización del aparato.
0
50
40
30
20
10
2
1
0
0
0
50
40
30
20
10
2
1
0
2
3
4
5
6
1
RPM
23000
22000
19500
17000
14500
12000
0
BM 2610967928 1/97 12/7/98, 10:29 AM1

2
18
10 20
19
17
16
1
2
3
4
5
6
1
2
3
4
5
6
7
15
8
9
10
11
12
13
14
26
BM 2610967928 1/97 12/7/98, 10:29 AM2

3
Product Data - Plunge Router
Model number 1613 1613EVS.
Identification number 0 601 613 0 . . 0 601 613 7 .
Router bit capacity 1-5/8" dia. max. 1-5/8" dia. max.
Collet capacity 1/4", 3/8", & 1/2" shanks 1/4", 3/8", & 1/2" shanks
Model number 1614 1614EVS.
Identification number 0 601 614 0 . . 0 601 614 7 .
Router bit capacity 1-5/8" dia. max. 1-5/8" dia. max.
Collet capacity 1/4" shank 1/4" shank
NOTE: This tool is designed for use with alternating current (AC) only.)
Accessory Listing
1613 & 1613EVS 1614 & 1614EVS
1/4" Collet chuck* 1/4" Collet chuck*
3/8" Collet chuck 3/4" Collet wrench*
1/2" Collet chuck* Deluxe router guide
15/16" Collet wrench* Vacuum attachment
Deluxe router guide Vacuum hose
Vacuum attachment Hose/vacuum adaptor
Vacuum hose Carrying case
Hose/vacuum adaptor
Carrying case
(* = standard equipment)
Router Components
1. Fine adjust knob 14. Chip deflector
2. Variable speed dial (1613EVS & 1614EVS) 15. Subbase
3. Depth indicator rod 16. Plunge lock/release lever
4. Depth indicator 17. Index marker
5. Depth indicator lock/release knob 18. Trigger switch
6. Templet guide lock/release lever 19. Vacuum attachment
7. Revolving depth turret 20. Vacuum hose
8. "Lock-ON" button 21. Retaining ring
9. Router guide adustment knob 22. Collet
10. Deluxe router guide 23. Collet nut
11. Spindle lock 24. Templet guide
12. Guide plate 25. Collet chuck assembly
13. Guide plate 26. Router bit
27. Template pattern
(NOTE: Router components not illustrated on page 2 are illustrated elsewhere in this manual)
BM 2610967928 1/97 12/7/98, 10:29 AM3

4
WARNING! “READ ALL INSTRUC-
TIONS”. FailuretofollowtheSAFETYRULES
identified by the BULLET (•) symbols listed
BELOW and other safety precautions, may
result in serious personal injury. Keep these
operating instructions with this product.
GENERAL SAFETY RULES
for all Power Tools
Work Area
• KEEP WORK AREAS CLEAN. Cluttered
areas and benches invite accidents.
• AVOID DANGEROUS ENVIRONMENT.
Don’tusepowertoolsindamporwetlocations.
Do not expose power tools to rain. Keep work
area well lit.
• AVOID GASEOUS AREAS. Do not oper-
ate portable electric tools in explosive atmo-
spheres in presence of flammable liquids or
gases. Motors in these tools normally spark,
and the sparks might ignite fumes.
• KEEP CHILDREN AWAY. Do not let
visitors contact tool or extension cord. All
visitors should be kept away from work areas.
Personal Safety
• GUARD AGAINST ELECTRIC SHOCK.
Prevent body contact with grounded surfaces
suchas pipes,radiators,rangesandrefrigerator
enclosures. Rubber gloves and non-skid foot-
wear are recommended when working out-
doors, where damp or wet ground may be
encountered. A Ground Fault Circuit Inter-
rupter protected power line must be used for
these conditions.
• DRESS PROPERLY. Do not wear loose
clothing or jewelry. They can be caught in
movingparts. Wear protectivehaircoveringto
contain long hair.
• USE SAFETY EQUIPMENT. WEAR
SAFETY GOGGLES or glasses with side
shields. Wear hearing protection during ex-
tended use of power tools and dust mask for
dusty operations.
• STAY ALERT. USE COMMON SENSE.
Watchwhatyou are doing. Donotoperate tool
when you are tired or under influence of drugs.
• REMOVE ADJUSTING KEYS AND
WRENCHES. Formhabitofcheckingtoseethat
keysand adjustingwrenchesareremovedfrom
tool before turning it on.
• AVOIDACCIDENTALSTARTING. Don’t
carry plugged in tool with finger on switch. Be
suretheswitchisOFF beforebeingplugged in.
• DON’T OVERREACH. Keep proper foot-
ing and balance at all times.
• BEFORE CONNECTING THE TOOL to a
power supply (receptacle, outlet, etc.) be sure
the voltage supplied is the same as that speci-
fied on the tool’s nameplate. A power supply
with voltage greater than that specified for the
tool can result in serious injury to the user - as
wellasdamagetothetool. Ifindoubt,DONOT
PLUG IN THE TOOL. Using a power supply
with voltage less than the nameplate rating is
harmful to the motor.
“VoltsAC”designatedtoolsareforAlternating
Current 50-60 Hz only. “Volts DC” designated
tools are for Direct Current. Do not use AC
designatedtoolswith DCpowersupply.Donot
use electronic speed controlled tools with DC
power supply.
Tool Use and Care
• DON’T FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
• USE RIGHT TOOL. Don’t force small tool
orattachmenttodothejobofaheavy-dutytool.
Don’t use tool for purpose not intended - for
example; don’t use a circular saw for cutting
tree limbs or logs.
• SECURE WORK. Use clamps or a vise to
hold work. It’s safer than using your hand and
it frees both hands to operate the tool.
• DON’TABUSECORD. Nevercarrytoolby
cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
Always keep cord away from the spinning
blade, bits or any other moving part while the
tool is in use.
• OUTDOOR USE EXTENSION CORDS.
Whentoolis used outdoors, useonlyextension
cordssuitableforuseoutdoorsandmarkedwith
suffix W-A (for UL), or W (for CSA). Refer to
section“ExtensionCords”,forpropercorduse.
• DISCONNECT TOOLS. When not in use,
before servicing, or when changing blades,
bits, cutters, etc.
• STORE IDLE TOOLS. When not in use,
tools should be stored in dry, high or locked up
place - out of the reach of children.
BM 2610967928 1/97 12/7/98, 10:29 AM4

5
• DO NOT ALTER OR MISUSE TOOL.
Thesetoolsare precisionbuilt. Any alterations
or modifications not specified is misuse and
may result in a dangerous condition.
• THE USE OF ANY ACCESSORIES not
specified in this manual may create a hazard.
• MAINTAIN TOOLS WITH CARE. Keep
toolssharpandcleanforbetterandsaferperfor-
mance. Follow instructions for lubricating and
changing accessories. Inspect tool cords peri-
odically and if damaged, have repaired by au-
thorized service facility. Inspect extension
cordsperiodicallyandreplaceifdamaged. Keep
handlesdry,clean andfreefrom oil andgrease.
• CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part that is
damaged should be carefully checked to deter-
mine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, binding of moving parts, break-
age of parts, mounting, and any other condi-
tions that may affect its operation. A guard or
other part that is damaged should be promptly
andproperlyrepaired orreplaced. Havedefec-
tiveswitchesreplaced. Donotusetoolifswitch
does not turn it on or off.
• ALL REPAIRS, ELECTRICAL OR ME-
CHANICAL, should be attempted only by
trained repairmen. Contact the nearest Bosch
Factory Service Center, or Bosch Authorized
Service Center or other competent repair cen-
ter. Use only Bosch replacement parts, any
other may create a hazard.
• If router bit is protruding through the base,
never lay the router down until the motor has
come to a complete standstill.
• Never hold the workpiece in one hand and
the router in other when in use. Always clamp
the material and hold the router securely with
both hands.
• Never use bits that have a cutting diameter
greater than the opening in the base.
• Afterchangingthebitsormakinganyadjust-
ments, make sure the collet nut and any other
adjustment devices are securely tightened be-
fore using the router.
• The direction of feeding the router into the
material is very important and it relates to the
direction of bit rotation. When viewing the
router from the top, the bit rotates clockwise.
When the router is located between your body
and the material, the feed direction must be to
theright. Ifthematerialislocatedbetweenyour
body and the router, then the feed direction
must be to the left. Feeding the router in the
wrong direction causes the cutting edge of the
bit to climb out of the work and pull the router
in the direction of this feed.
Safety Rules for Routers
• Neverstarttherouterwhenthebitisengaged
inthematerial. Thebit’scuttingedgemaygrab
the material causing the router to get out of
control. Alwaysholdtherouter withtwohands
during start-up. The reaction torque of the
motor can cause the router to twist.
• Alwaysmakesuretheworkpieceisfreefrom
nailsandother foreign objectswhich can cause
the bit and router to jump and damage the bit.
• Always wear safety goggles. If router has a
removablechip deflector,keepitinplacewhen
routing.
• Never touch the router bit or other moving
part during use. After use the router bit is too
hot to be touched by bare hands.
Double Insulated Tools
• Double Insulation is a design concept
used in electric power tools which eliminates
theneedforthethreewiregroundedpowercord
and grounded power supply system. It is a
recognized and approved system by
Underwriter’s Laboratories, CSA and Federal
OSHA authorities.
IMPORTANT: Servicing of a tool with
double insulation requires care and knowledge
of the system and should be performed only by
a qualified service technician. WHEN SER-
VICE IS REQUIRED USE ONLY IDENTI-
CAL REPLACEMENT PARTS.
POLARIZEDPLUGS: Ifyourtoolisequipped
with a polarized plug (one blade is wider than
the other), this plug will fit in a polarized outlet
onlyoneway. Iftheplugdoesnotfitfullyinthe
outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the
proper outlet. To reduce the risk of electric
shock do not change the plug in any way.
BM 2610967928 1/97 12/7/98, 10:29 AM5

6
Variable Speed with Dial Setting
(1613EVS & 1614EVS)
Your router is also equipped with a variable
speeddial2. The routerbit speed canbepreset
from 12,000 to maximum nameplate RPM by
rotatingthedialtothe desiredsetting. Thedial
maybesetonorbetweenanyofsixpositions(1
= low through 6 = high). The "Lock-ON"
button may also be used with any setting of the
dial.
Thefollowingspeedsgenerally apply, butpre-
cise settings are largely determined by
experience with the material being cut. Mo-
mentaryspeedvariationisnormalwhenstarting
the router until the electronic regulator takes
control.
Dial 1613EVS 1614EVS
Setting RPM RPM Material
1 12,000 12,000 nonferrous metals,
2 14,000 14,500 larger diameter router
3 16,000 17,000 bits and cutters.
4 18,000 19,500 Softwoods, plastics,
5 20,000 22,000 counter tops, smaller
6 22,000 23,000 diameter router bits
and cutters.
"Soft Start" Feature
(1613EVS & 1614EVS )
The router is equipped with the "soft start"
feature which gradually increases the starting
speed and torque, reducing the stress that oc-
curs from a high torque start.
Start the tool before applying to work and let
the tool come to full speed before contacting
the workpiece. Lift the tool from the work
before releasing the switch. DO NOT turn the
switch"ON" and"OFF"while thetool isunder
load; this will greatly decrease the switch life.
Router Bit Installation and Removal
WARNING!Always disconnect the tool
from the power supply before installing router
bits, accessories or making any adjustments.
Installing a Router Bit
Turn the armature shaft to align the flats with
the spindle lock 11, and press the spindle lock
firmlydowntoengage it. Next,usethewrench
supplied to loosen the collet chuck assembly.
Insert the shank of the router bit into the collet
chuck as far as it will go, then back the shank
Cord Length
Trigger Switch with "Lock-ON"button
Your tool can be turned "ON" or "OFF" by
squeezing or releasing the trigger. Your tool is
alsoequippedwith "Lock-ON"button,located
ontheleftsideofthetriggerhandle,thatallows
for continuous operation without holding the
trigger.
TO LOCK SWITCH "ON": Squeeze trigger,
depress button and release trigger.
TOUNLOCKTHESWITCH:Squeezetrigger
and release it without depressing the "Lock-
ON" button.
WARNING!Ifthe"Lock-ON"buttoniscon-
tinuously being depressed, the trigger cannot
be released.
Operating the Tool
Extension Cords
• Replacedamagedcordsimmediately.Use of
damaged cords can shock, burn or electrocute.
• Ifanextension cordis necessary,acord with
adequate size conductors should be used to
prevent excessive voltage drop, loss of power
or overheating. The table below shows the
correct size to use, depending on cord length
andamperageratingonthetool’snameplate. If
in doubt, use the next heavier gauge. Always
use U.L. and CSA listed extension cords.
Ampere Rating (shown on nameplate)
0- 2.1- 3.5- 5.1- 7.1- 12.1-
2.0 3.4 5.0 7.0 12.0 16.0
25' 18 18 18 18 16 14
50' 18 18 16 16 14 12
75' 18 18 16 14 12 10
100' 18 16 14 12 10
150' 16 14 12 12 Wire Gauge
Note: Thesmallerthegaugenumber,thelarger
the wire is in the cord.
"SAVE THESE INSTRUCTIONS"
BM 2610967928 1/97 12/7/98, 10:29 AM6

7
22
23
21
25
lightly thread the collet chuck back onto the
armature shaft. Replace worn or damaged
collet chucks immediately.
Plunge Mechanism
To release the plunge mechanism, grasp the
routerhandlesfirmlywithbothhandsandpress
theplungelock/releaselever16withthethumb
of the left hand. The motor may then be raised
or lowered to the desired position. The plunge
lock/release lever is spring-loaded, and will
holdtheroutermotorinpositionwhenpressure
on the lock lever is released. When plunging,
always apply uniform firm pressure to both
handles to avoid cocking the motor on the
posts.
Indicator Rod and Turret
The depth indicator rod 3and the revolving
depth turret 7are used to control cutting depth
as follows;
With the bit installed, gently lower the motor
until the tip of the router bit just contacts the
level surface the router is sitting on. This is the
“zero” position, from which further depth ad-
justments can be accurately made. To set a
desired depth of cut, rotate revolving depth
turret until the lowest step is aligned with the
depth indicator rod. Loosen depth indicator
lock/releaseknob 5andlower thedepth indica-
tor rod until it contacts the lowest step of the
turret. Slide the depth indicator 4until the red
lineindicateszeroonthedepthscale,indicating
thepointatwhichthebitjustcontactsthework.
To set a desired cutting depth, slide the depth
indicator rod up until the red depth indicator
line attains the desired cutting depth, and se-
curetherodinpositionbyfirmlytighteningthe
depthindicatorlock/releaseknob. Thedesired
depth of cut may now be achieved by plunging
therouteruntil thedepthindicator rodcontacts
the selected stop on the revolving depth turret.
To be certain that your depth settings are accu-
rate, you may want to make test cuts in scrap
material before beginning work. Once the de-
sired final depth has been set on the lowest
depth turret setting with the depth indicator
rod,it ispossibleto makeprogressively deeper
cuts by starting with a higher flat on the depth
turret and after each cut, rotating the revolving
out until the cutters are approximately 1/8" to
1/4"awayfrom thecolletchuckface. Withthe
router bit inserted and the spindle lock fully
engaged, tighten the collet chuck assembly
firmly in a clockwise direction, (viewed from
undertherouter),withthewrenchsupplied. To
avoiddamagingthecolletchuck,never tighten
the collet chuck unless a router bit of proper
shank size is inserted into the collet.
To ensure proper gripping of the router bit and
minimize run-out, the shank of the router bit
should always be inserted at least 5/8".
CAUTION! To prevent damage to tool. Do
nottightencolletwithoutabit. NOTE: Thebit
shank and chuck should be clean and free of
dust, wood, residue and grease before assem-
bling.
CAUTION! Do not use router bits greater
than 1-5/8" in diameter as they will not fit
through the base casting.
Removing the Router Bit
Use the spindle lock and wrench as described
above, and turn the collet chuck assembly in a
counter-clockwise direction. Once the collet
chuck assembly is loosened, continue to turn
the collet chuck until it pulls the collet free
from its taper, and the router bit can be re-
moved.
NOTE:Thecollet chuckisself-extracting; itis
NOTnecessarytostrikethecolletchucktofree
the bit.
Collet Chuck Care
With the router bit removed, continue to turn
the collet chuck counter-clockwise until it is
free of the shaft. To assure a firm grip, occa-
sionally blow out the collet chuck with com-
pressed air, and clean the taper in the armature
assembly shaft with a tissue or fine brush. The
collet chuck is made up of three component
parts as illustrated;
check to see that the re-
taining ring 21 is prop-
erly located around the
collet 22 and seated in
the inner groove of the
collet chuck nut 23 and
BM 2610967928 1/97 12/7/98, 10:29 AM7

8
around the workpiece. If you were cutting an
openinginthecenterofapanel,youwouldfeed
the router in a clockwise direction, so that the
edge of the opening would be cut against the
rotationofthe router bitasdescribed, and have
a smooth finish. Whenever you are cutting
completely around a workpiece, it is advisable
to cut across the grain first, so any corner
tearout may be smoothed by cutting with the
grain on the second pass.
Rate of Feed
When routing or doing related work in wood
and plastics, the best finishes will result if the
depth of cut and feed rate are regulated to keep
the motor operating at high speed. Feed the
routeratamoderaterate. Softmaterialsrequire
a faster feed rate than hard materials.
The router may stall if improperly used or
overloaded. Reduce the feed rate to prevent
possibledamagetothetool. Alwaysbesurethe
collet nut is tightened securely before use.
Alwaysuse routerbits withthe shortestcutting
length necessary to produce the desired cut.
This will minimize router bit run-out and chat-
ter.
Templet Guides
Therouterisequippedwithanexclusivequick-
changetempletguidemechanism,whichfirmly
grips the guides with a spring-loaded ring built
intothebase. Toin-
sert or change the
templetguide24,re-
tract the templet
guide lock/release
lever 6.Align any
two of the four cut-
away tabs on the
templet guide to the
twocast-inbossesin
thetempletguidere-
cess of the base.
depth turret to progressively lower stops as
desired, until the final depth (lowest step or
flat) is reached.
Fine adjustment
The router is equipped with a true micrometer-
typefineadjustmentmechanism,which canbe
used in any plunge position and provides pre-
cise adjustment of the router bit position for
unmatchedaccuracy. Whenthetoolisplunged
totheapproximatepositiondesired,thisdevice
maybeadjustedto precisely setthefinalcutter
position.
To use the fine adjustment, turn the fine adjust
knob 1clockwise to lower the router bit or
counter-clockwise to raise it, as indicated by
the arrow molded into the top of the knob. To
allow precise settings, the indicator ring is
graduated in English and Metric increments,
andeachlineisequalto1/10mmor.004". The
indicator ring may be reset to zero without
moving the fine-adjust knob, to allow the user
to begin the adjustment from any reference
point desired.
The fine adjustment mechanism has a total
adjustmentrangeof5/8",which isindicatedby
the two lines printed on back of the housing.
Whenever the fine adjustment is used, be cer-
tain that the index marker 17 is positioned
betweenthesetwolinestoensurethattherewill
be enough travel in the desired direction after
the router is plunged into position. Note that
when the router is plunged to maximum depth
or is fully retracted to the top of the posts, the
fine adjustment mechanism will not move the
motor further down or up, as the full extension
of the travel has been reached at these points.
Similarly,thefineadjustmentcannotlowerthe
bit when the depth indicator rod is tightened
against the depth turret.
Direction of Feed
The router rotates in a clockwise direction, as
viewed from the top of the router. The correct
relationship between direction of router bit or
cutter rotation and router feed is shown below.
It is very important to move the router in the
proper direction or router bit chatter and rough
cutting will be the result. As an example, to
routadecorativeedgeonthefrontofatabletop,
you would move the router from left to right to
perform the operation, or counter-clockwise
26
23
24
6
WORK
CUTTER DIRECTION
OF FEED
BM 2610967928 1/97 12/7/98, 10:29 AM8

9
Insert the templet guide and release the lock
lever to grip the templet guide in place.
Templet guides are used with a number of
specialaccessories,suchashinge templetsand
dovetail fixtures which are listed in your
BOSCH catalog. In addition, special templets
are easily prepared for cutting repeated pat-
terns, special designs, inlays, and other
applications. Atempletpatternmaybemadeof
plywood,hardboard,metalorevenplastic,and
the design can be cut with a router, jigsaw, or
other suitable cutting tool. Remember that the
pattern will have to be made to compensate for
the distance between the router bit and the
templet guide 24, as the final workpiece will
differinsizefromthetempletpattern27bythat
amount, due to the cutter position.
Deluxe Router Guide
For routing operations such as grooving or
dadoing, it is often necessary to guide the tool
ina lineparallel toa straightedge. Onemethod
of obtaining a straight cut is to securely clamp
a board or other straightedge to the work sur-
face, and guide the edge of the router sub-base
alongthispath.Itisbesttokeeptherouterinone
position as it is moved along the guide, as this
will produce the straightest cut.
The Bosch deluxe router guide is an accessory
that will guide the router parallel to a straight
edge or around a curved surface. The deluxe
router guide is supplied with two rods and a
series of wing nuts and screws to fasten the
guide and adjust its position relative to the bit.
Withtheguideinstalledandadjusted,therouter
should be fed normally, keeping the guide in
contact with the edge of the workpiece at all
times. The deluxe router guide may also be
positioned under the router base for operations
where a limited amount of bit exposure is de-
sired.
The Bosch deluxe router guide includes a
fine-adjustmentmechanismforextraprecision,
andremovablefaceplatesforguidingtherouter
along straight or curved surfaces. For proper
operation,pleaserefertotheinstructionswhich
are included with this accessory.
Chip Extraction
Your router may be fitted with optional chip
extractionaccessories,whichareavailablefrom
your Bosch dealer. Chip extraction is most
effective on grooving, dadoing, and other flat-
surface operations where flying chips can be
controlled. It is less effective on edge forming
orwhentemplateguidesareusedasthevacuum
efficiency is greatly diminished in such cir-
cumstances.
WARNING! Useofanyaccessorynotspeci-
fied in this manual or the BOSCH catalog for
use with this tool may create a hazard.
Maintenance and Service
WARNING! Preventive maintenance per-
formed by unauthorized personnel may result
inmisplacingofinternalwiresandcomponents
which could cause serious hazard. We recom-
mend that all tool service be performed at a
Bosch Factory Service Center.
Tool Lubrication
Your Bosch tool has been properly lubricated
andisready foruse.We recommend,that tools
with gears be regreased with a special gear
lubricant every time the brushes are changed.
Carbon Brushes
The brushes and commutator in your Bosch
tool have been engineered for many hours of
dependable service. To maintain peak effi-
ciency of the motor, we recommend that every
two to six months the brushes be examined.
Onlygenuine Bosch replacementbrushes spe-
cially designed for your tool should be used.
Bearings
After about 300-400 hours of operation, or at
everysecondbrushchange,thebearingsshould
be replaced at a Bosch Factory Service Center.
Bearings which become noisy (due to heavy
load or very abrasive material cutting) should
be replaced at once to avoid overheating and
motor failure.
23
26 24 27
BM 2610967928 1/97 12/7/98, 10:29 AM9

10
Cleaning
WARNING! To avoid accidents, always
disconnect the tool from the power supply
beforecleaningorperforminganymaintenance.
The tool may be cleaned most effectively with
compressed air. Always wear safety goggles
when cleaning tools with compressed air.
Ventilationopeningsandswitchleversmustbe
kept clean and free of foreign matter. Do not
BOSCH Power Tool Authorized Service Sta-
tions, please refer to your phone directory.
THIS LIMITED WARRANTY DOES NOT
APPLYTO ACCESSORYITEMSSUCH AS
CIRCULAR SAW BLADES, DRILL BITS,
ROUTER BITS, JIGSAW BLADES, SAND-
ING BELTS, GRINDING WHEELS AND
OTHER RELATED ITEMS. ANY IMPLIED
WARRANTIES SHALL BE LIMITED IN
DURATION TO ONE (1) YEAR FROM
DATE OF PURCHASE. SOME STATES IN
THEU.S.DONOT ALLOW LIMITATIONS
ONHOWLONGANIMPLIEDWARRANTY
LASTS, SO THE ABOVE LIMITATION
MAYNOTAPPLYTOYOU. INNOEVENT
SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING BUT NOT LIM-
ITED TO LIABILITY FOR LOSS OF PROF-
ITS) ARISING FROM THE SALE OR USE
OF THIS PRODUCT. SOME STATES IN
THE U.S. DO NOT ALLOW THE EXCLU-
SION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLU-
SION MAY NOT APPLY TO YOU. THIS
LIMITED WARRANTY GIVES YOU SPE-
attempt to clean by inserting pointed objects
through openings.
CAUTION! Certain cleaning agents and
solvents damage plastic parts. Some of these
are: gasoline,carbontetrachloride,chlorinated
cleaning solvents, ammonia and household
detergents that contain ammonia.
S-B Power Tool Company
4300 W. Peterson Avenue
Chicago, IL 60646-5999
WARRANTY
BOSCH
S-B POWER TOOL COMPANY
LIMITED WARRANTY
S-B Power Tool Company (“Seller”) war-
rants, to the original purchaser only, that all
BOSCHportablepowertoolswillbefreefrom
defects in material or workmanship for a pe-
riod of one (l) year from date of purchase.
SELLER’S SOLE OBLIGATION AND
YOUR EXCLUSIVE REMEDY under this
Limited Warranty and, to the extent permitted
by law, any warranty or condition implied by
law,shallbetherepairorreplacementofparts,
without charge, which are defective in mate-
rial or workmanship and which have not been
misused, carelessly handled, or misrepaired
by persons other than Seller or Authorized
Service Stations. To make a claim under this
Limited Warranty, you must return the com-
plete portable power tool product, transporta-
tion prepaid, to any BOSCH Factory Service
Center or Authorized Service Station. A list-
ingofU.S.BOSCHFactoryServiceCentersis
packed with each BOSCH Power Tool. For
BM 2610967928 1/97 12/7/98, 10:29 AM10