
18 | English
1 609 92A 16H | (16.2.15) Bosch Power Tools
Switching On and Off
Adjust the depth-of-cut before switching on or off; see Sec-
tion “Adjusting the Depth-of-cut”.
To start the machine, press the On/Off switch 29 and keep it
pressed.
To lock the pressed On/Off switch 29, press the lock-on but-
ton 2.
To switch off the machine,release the On/Off switch 29 or
when it is locked with the lock-on button 2, briefly press the
On/Off switch 29 and then release it.
To save energy, only switch the power tool on when using it.
Constant Electronic Control
Constant electronic control holds the speed constant atno-
load and under load, and ensures uniform working perfor-
mance.
Soft Starting
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
Overload Protection
The overload protection prevents impermissibly high current
consumption in the event of extreme overload. This can lead
to a reduction in motor speedand power output or in extreme
cases to motor standstill.
Oncetheload has beenremovedfrom the powertool,the mo-
tor immediately runs up or back to working speed.
Restarting Protection
Therestartingprotectionfeaturepreventsuncontrolledrestart-
ing of the machine after an interruption in the power supply.
To restart the operation, switch the On/Off switch 29 to the
Off position and start the machine again.
Release lever (see figure C)
The release lever 23 is automatically reset when you let go of
it. For better holding force, the release lever 23 must be
pulled back all the way. The holding force can be readjusted if
required. To do so, insert an Allen key (4 mm) into the open-
ingonthehandle.Turn theAllenkeyclockwiseto increasethe
holding force, and turn it anticlockwise to reduce the holding
force.
Adjusting the Depth-of-cut (see figure D and E)
Theadjustmentofthe depth-of-cutmayonly becarried
out when the router is switched off.
For coarse adjustment of the depth-of-cut, proceed as fol-
lows:
– Place the machine with the router bit mounted on the
workpiece to be machined.
– Set the fine-adjustment path to the centre position with
the adjustment knob 25. For this, turn the adjustment
knob 25 until the marks 19 match as shown in the figure.
Afterwards, set the scale 24 to “0”.
– Setthestep buffer9to the lowest position; the step buffer
engages noticeably.
– Loosen the screw 15 on the depth stop 14 so that the
depth stop 14 is freely movable.
– Pressthereleaselever23backandslowly guidethe router
down until the router bit 5touches the workpiece surface.
Let go of the release lever 23 again to lock this position.
– Pressthedepthstop14downuntilitsits onthe stepbuffer
9.
GOF 1250 LCE: Switch on the digital depth setting at the
On/Off switch 18. Press the button 16 for setting the zero
point of the depth stop 14.
GOF 1250 CE: Set the slide with the index mark 27 to po-
sition “0” on the depth-of-cut scale 26.
– Set the depth stop 14 to the required depth-of-cut and
tighten the screw 15 on the depth stop 14.
GOF 1250 CE: Make sure you do not adjust the slide with
the index mark 27 any more.
– Push the release lever 23 and guide the plunge router to
the uppermost position.
For deep cuts, it is recommended to carry out several cuts,
each with little material removal. By using the step buffer 9,
thecuttingprocesscanbedividedintoseveralsteps.Forthis,
adjust the desired depth-of-cut with the lowest step of the
step buffer and select the higher stepsfirstfor theinitial cuts.
The clearance of the steps can be changed by screwing the
adjusting screws 10 further in or out.
After a test run, the depth-of-cut can be set to the required di-
mension by turning the adjustment knob 25; turning in a
clockwise direction increases the depth-of-cut; turning in an
anticlockwisedirectiondecreasesthedepth-of-cut.The scale
24 can be used for guidance. One revolution corresponds
with a setting range of 2,0 mm, one of the graduation marks
on the bottom edge of the scale 24 changesthe setting range
by 0,1 mm. The maximum setting range is ± 8 mm.
Example:Therequireddepth-of-cut shouldbe10.0 mm,and
the test cut resulted in a depth-of-cut of 9.6 mm.
–Turnthescale24 to “0”.
– Turn theadjustment knob25clockwise by0.4 mm/4grad-
uation marks (difference between target and actual val-
ues).
– Check the selected depth-of-cut by carrying out another
trial cut.
GOF 1250 CE: After setting the depth-of-cut, do not change
the position of the slide 27 on the depth stop 14 any more so
thatyou canalwaysread thecurrentdepth-of-cuton thescale
26.
GOF 1250 LCE: Thecurrentdepth-of-cutis shownonthe dis-
play 21.
Working Advice
Protect router bits against shock and impact.
Direction of Feed and Routing Process (see figure F)
Therouting processmust alwaysbecarriedoutagainst
the rotation direction of the router bit 5 (up-cutting
motion). When routing in the direction with the rota-
tion of the router (down-cutting), the machine can
break loose, eliminating control by the user.
19
OBJ_BUCH-2018-004.book Page 18 Monday, February 16, 2015 1:39 PM