Bosch BSP3200 User manual
2 |
(1)(2)(3)(1)(2)(5)(6)(7)(8)(10)(9)(4)
0 275 008 3SG | (25.01.2022)Bosch eBike Systems
| 3
1
2
2
1
A
B(6)(12)(5)(11)(5)(5)(4)(16)
Bosch eBike Systems0 275 008 3SG | (25.01.2022)
4 |
1
2
C(15)(1)
1
2
D(13)(14)
0 275 008 3SG | (25.01.2022)Bosch eBike Systems
English – 1Safety InstructionsRead all the safety information and in-structions. Failure to observe the safety in-formation and follow instructions may resultin electric shock, fire and/or serious injury.Save all safety warnings and instructions for future ref-erence.uRead and observe the safety warnings and directionscontained in all the eBike system operating instruc-tions and in the operating instructions of your eBike.uDo not allow your attention to be diverted from sur-rounding traffic when using Bosch eBike componentsand always ride with both hands on the handlebars. Al-ways observe the applicable legal provisions in yourcountry for the permitted use of your bicycle in roadtraffic. In particular, note that it is prohibited to pickup or hold your smartphone in your hand in roadtraffic.uSet the display brightness so that you can adequatelysee important information such as speed and warningsymbols. Incorrectly set display brightness may lead todangerous situations.uThe contact surfaces of the display holder may be-come very hot (>60°C). Allow the contact surfaces toadjust to the ambient temperature before you touchthem. This is particularly important when using a Smart-phoneGrip.uConsult a doctor before using fitness app programs.Fitness apps may cause people to overexert themselvesphysically.uAlways observe local restrictions for using electronicdevices.uAvoid operation near your body for extended periods.uDo not stand your bicycle upside down on its saddleand handlebars if the SmartphoneGrip or its holderprotrude from the handlebars. This may irreparablydamage the SmartphoneGrip or the holder.uDo not use the SmartphoneGrip as a handle. Lifting theeBike up by the SmartphoneGrip can cause irreparabledamage to the SmartphoneGrip.uDo not open the SmartphoneGrip. Opening the Smart-phoneGrip may damage it beyond repair and void anywarranty claims.uCaution! When using the SmartphoneGrip withBluetooth® and/or Wi-Fi, interference can occur withother devices and equipment, aircraft and medicaldevices (e.g. pacemakers, hearing aids). Likewise, injuryto people and animals in the immediate vicinity cannot beexcluded entirely. Do not use the SmartphoneGrip withBluetooth® in the vicinity of medical devices, petrol sta-tions, chemical plants, areas with a potentially explosiveatmosphere or on blast sites. Do not use the Smart-phoneGrip with Bluetooth® in aeroplanes. Avoid opera-tion near your body for extended periods.Bosch eBike Systems0 275 008 3SG | (25.01.2022)
NOTICE: This device complies with part 15 of the FCCRules. Operation is subject to the following two conditions:1.This device must not cause harmful interference, and2.this device must accept any interference received, in-cluding interference that may cause undesired opera-tion.NOTICE: Changes or modifications made to this equipmentnot expressly approved by the Robert Bosch GmbH may voidthe FCC authorization to operate this equipment.NOTE: This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a resi-dential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful in-terference to radio communications. However, there is noguarantee that interference will not occur in a particular in-stallation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the follow-ing measures:–Reorient or relocate the receiving antenna.–Increase the separation between the equipment and re-ceiver.–Connect the equipment into an outlet on a circuit differ-ent from that to which the receiver is connected.–Consult the dealer or an experienced radio/TV technicianfor help.Radiofrequency radiation exposure Information: The ra-diated output power of the device is far below the FCC radiofrequency exposure limits. Nevertheless, the device shall beused in such a manner that the potential for human contactduring normal operation is minimized.This equipment complies with FCC radiation exposure limitsset forth for an uncontrolled environment. This equipmentshould be installed and operated with minimum distance of20 cm between the radiator and your body. This transmittermust not be co-located or operating in conjunction with anyother antenna or transmitter.ISED Notice (Canada)This device contains licence-exempt transmitter(s)/re-ceiver(s) that comply with Innovation, Science and Eco-nomic Development Canada’s licence-exempt RSS(s). Oper-ation is subject to the following two conditions:1.this device may not cause interference, and2.this device must accept any interference, including in-terference that may cause undesired operation of thedevice.This equipment complies with Canada radiation exposurelimits set forth for an uncontrolled environment. This equip-ment should be installed and operated with minimum dis-tance of 20 cm between the radiator and your body. Thistransmitter must not be co-located or operating in conjunc-tion with any other antenna or transmitter.Remarques ISDE (Canada)Cet appareil contient un/des émetteur(s)/récepteur(s) exempt(s) de licence conforme(s) aux CNR d’Innovation, Sciences et Développement économique Canada appli-cables aux équipements exempts de licence. L’utilisation est autorisée sous réserve des deux conditions suivantes :1.l’appareil ne doit pas produire de brouillage, et2.l’appareil doit accepter tout brouillage radioélectriquesubi, même si le brouillage est susceptible d’en compro-mettre le fonctionnement.Cet équipement respecte les limites d’exposition aux rayon-nements définies par le Canada pour un environnement noncontrôlé. Cet équipement doit être installé et utilisé en main-tenant une distance minimale de 20cm entre la source derayonnement et votre corps. Cet émetteur ne doit pas êtreplacé à proximité d’une autre antenne ou d’un autre émet-teur ou être utilisé en combinaison avec n’importe quelleautre antenne ou émetteur.English – 20 275 008 3SG | (25.01.2022)Bosch eBike Systems
Intended UseProduct FeaturesThe numbering of the components shown refers to the illus-trations on the graphics pages at the beginning of themanual.All illustrations of bike parts except for the drive unit, Smart-phoneGrip (including operating unit), speed sensor and thecorresponding holders are a schematic representation andmay differ on your eBike.(1)Front retraining bracket, movable(2)Rear retaining bracket, fixed(3)USB port with USB cap(4)Release mechanism(5)SmartphoneGrip mount(6)Snap-in hook(7)Socket contacts(8)SmartphoneGrip contacts(9)Status LED(10)Inductive charging coil(11)Display mount fastening screw(12)Removal blocker(13)Keypad lock(14)Hex key(15)Smartphone(16)Adapter trayTechnical DataSmartphoneGripProduct codeBSP3200USB charging output powerW5W (1A at 5Vdc)Wireless charging outputpowerWmax 7.5W (1.5A at 5Vdc)Efficiency > 67%Maximum RF output power40.36dBuA/m at 3mdistanceFrequency rangeKHz110–205Operating temperature°C–5 to 40Storage temperature°C10 to 40Protection ratingIP54Weight, approx.g75Product Description andSpecificationsEnglish – 3Bosch eBike Systems0 275 008 3SG | (25.01.2022)The Bosch SmartphoneGrip is designed to hold and charge asmartphone on the handlebars of a Bosch eBike system.In addition to the functions shown here, changes to softwarerelating to troubleshooting and functional modifications maybe introduced at any time.The manufacturer accepts no liability for damage to mobiledevices caused by using this product. The manufacturer ac-cepts no liability for defects related to damage or loss due tofactors outside of the manufacturer's control, or for productsthat were modified or damaged due to improper or incorrectuse.
English – 4AssemblySmartphoneGrip Assembly (seefigureA)Press and hold the release mechanism(4) to position theSmartphoneGrip. Place the upper edge of the Smart-phoneGrip next to the snap-in hook(6) of the displayholder(5)➊. Pull the SmartphoneGrip towards you andpush the SmartphoneGrip onto the display holder➋. Let goof the release mechanism(4).Press the release mechanism(4) while pulling it towardsyou➊ to remove the SmartphoneGrip. Remove the Smart-phoneGrip and let go of the release mechanism(4)➋.Inserting the Removal Blocker (seefigureB)Insert the removal blocker(12) into the adapter tray(16)from below until you hear the removal blocker(12) click intoplace.From this point onwards, you can no longer remove theSmartphoneGrip from the display mount(5) without remov-ing the display mount(5) from the adapter tray(16) byloosening the two fastening screws(11).Note: The removal blocker(12) is not an anti-theft device.Smartphone Assembly (seefigureC)The SmartphoneGrip can hold smartphones in the followingsizes:
67–88 mm
6,8–13 mm
123–175 mm
The specified dimensions include any phone cases. Smart-phones with folio cases must not be used.The total weight must not exceed 276g.Pull the front retaining bracket(1) forwards➊. Insert yoursmartphone(15) with the long side of the phone positionedagainst the fixed retaining bracket(2)➋. Release the frontretaining bracket and place your smartphone(15) in thecentre of the SmartphoneGrip➌.uBe careful not to pinch your fingers between the movableretaining bracket and the SmartphoneGrip when insertingyour smartphone.Once you have inserted your smartphone, check that thesmartphone cannot come into contact with any hard parts onthe bike even in case of vibrations, as this could cause last-ing damage to the smartphone.Keypad Lock Assembly (seefigureD)To remove the keypad lock(13), unscrew the securingscrew with a hex key (1.5mm)(14)➊ and remove thekeypad lock(13)➋.To insert the keypad lock(13), slide the keypad lock(13)into the provided opening and screw it into place with a hexkey (1.5mm)(14).Note: The keypad lock is not an anti-theft device. Thekeypad lock prevents the SmartphoneGrip from beingquickly removed from the holder. The keypad lock does notaffect the smartphone in any wayNote: Never leave your smartphone unattended in theSmartphoneGrip.OperationStarting OperationPlace your smartphone in the SmartphoneGrip.Start theeBike Flow app to have riding data displayed.Depending on the smartphone's operating sys-tem, theeBike Flow app can be downloadedfree of charge from the Apple App Store andthe Google Play store.Use your smartphone to scan the code in order to downloadtheeBike Flow app.Charging your SmartphoneWhile the smartphone is in the SmartphoneGrip, it can becharged at the same time as displaying riding data. If yoursmartphone has an inductive charging function, you cancharge the smartphone without needing a cable.Inductive ChargingThe charging process starts automatically when you place asmartphone with an inductive charging function in theSmartphoneGrip. The status LED(9) lights up yellow. Whenthe smartphone is fully charged, the status LED(9) will lightup green permanently.The charging voltage is switched off when you remove thesmartphone from the holder.Charging via USBIf your smartphone does not have an inductive chargingfunction, you can charge your smartphone via the USBport(3). To do so, open the USB cap and connect a separateUSB cable (not included in the scope of delivery) to the Mi-cro-AB USB port.Pay attention to the type of plug required for your smart-phone when purchasing the USB cable.0 275 008 3SG | (25.01.2022)Bosch eBike Systems
English – 5Status IndicatorsThe status LED(9) indicates the following statuses with dif-ferent colours and lighting patterns:StatusBehaviourCharging via USBLED lights up blue.Inductive charging startsLED flashes yellow 3 times.Inductive chargingLED lights up yellow.Fully chargedLED lights up green.Inductive charging alarmLED flashes red.The following alarm states are detected and will lead to theinductive charging process being interrupted:–Detection of foreign objects, e.g. coins, keys or othermetallic objects–Temperature alarmThe charging process will switch off at temperaturesabove 78°C. The charging process is continued once thetemperature drops below 56°C.–Overvoltage alarm at voltages above 6V–Undervoltage alarm at voltages below 4.2VMaintenance and servicingMaintenance and cleaningUse a soft cloth dampened only with water for cleaning. Donot use cleaning products of any kind.uHave all repairs performed only by an authorised bikedealer.Do not clean any of the components with pressurised water.TransportuIf you transport your eBike attached to the outside ofyour car, e.g. on a bike rack, remove the Smart-phoneGrip and the eBike battery to avoid damagingthem.After-sales service and advice on using productsIf you have any questions about the eBike system and itscomponents, contact an authorised bicycle dealer.For contact details of authorised bike dealerships, pleasevisit www.bosch-ebike.com.DisposalThe drive unit, on-board computer incl. operat-ing unit, battery, speed sensor, accessoriesand packaging should be disposed of in an en-vironmentally correct manner.Check that your personal data has been deleted from thedevice.Do not dispose of eBikes and their components with house-hold waste.Please return Bosch eBike components that are no longer usable free of charge to an authorised bicycle dealer.Subject to change without notice.Bosch eBike Systems0 275 008 3SG | (25.01.2022)
English – 60 275 008 3SG | (25.01.2022)Bosch eBike Systems
繁體中文 – 1安全注意事項
請詳讀所有安全注意事項和指示。如
未遵守安全注意事項與指示，可能導
致火災、人員觸電及／或重傷。
請妥善保存所有安全注意事項與指示，以供日後查
閱之用。
u請仔細詳讀並遵守所有 eBike 系統操作說明書以
及您的 eBike 操作說明書中的安全注意事項和指
示。
u請勿因使用 Bosch eBike 機件而分心疏於交通狀
況並請務必將雙手放在把手上。請務必遵循您所
在國家許可於道路交通中使用您自行車的相關法
律。特別是禁止於道路上拿起或將智慧型手機拿
在手中。
u請適當調整螢幕亮度，使您能適當接收如車速、
警告標誌等重要訊息。未正確設定螢幕亮度可能
導致危險情況發生。
u螢幕支架的接觸面有可能變得很燙（>60°C）。
觸摸接觸面前，請先待其冷卻。尤其當您使用
SmartphoneGrip 時更是如此。
u使用健身 App 應用程式前請先向醫生諮詢。健身
App 可能造成人員體力透支。
u使用電子設備時請注意當地的限制。
u應避免直接貼靠在身體部位旁的長時間持續操
作。
uSmartphoneGrip 或其支架突出於把手時，請勿
以把手和坐墊為支撐將自行車倒置。
SmartphoneGrip 或支架可能會受損且無法修
復。
u請勿將 SmartphoneGrip 作為握把使用。若使
用 SmartphoneGrip 將 eBike 提起，可能會使
SmartphoneGrip 受損且無法修復。
u請勿將 SmartphoneGrip 拆開。任意拆開
SmartphoneGrip 可能導致其毀損並使產品保固
聲明失效。
u小心！使用 SmartphoneGrip 時若開啟
藍牙
®或/
功能，將可能對其他裝置或設備、飛機以及醫療
器材（例如心律調節器、助聽器等）產生干擾。
同樣亦無法完全排除對鄰近之人員或動物造成身
體危害的可能性。同樣亦無法完全排除對鄰近之
人員或動物造成身體危害的可能性。請勿在醫療
器材、加油站、化學設備、爆炸危險場所以及易
爆環境等處附近，使用 SmartphoneGrip 的
藍牙
®功能。請勿在飛機上使用 SmartphoneGrip 的
藍牙
®功能。應避免直接貼靠在身體部位旁的長時
間持續操作。
產品和規格性能
預定用途
Bosch SmartphoneGrip 是為將智慧型手機固定於
Bosch eBike 系統把手上並為其充電所設計。
除此處所示功能以外，隨時皆有可能引入軟體變
更，以排除故障及更動功能。
對於行動裝置因使用本產品可能產生的損毀，製造
商概不負責。對於因製造商無法控制因素而成的毀
損、損失所致之瑕疵或經改造、不當使用或用於非
正常用途而受損的產品，製造商概不負責。
插圖上的機件
機件的編號和本手冊最前面的詳解圖一致。
除了驅動單元、SmartphoneGrip，包括控制單
元、車速感測器和所屬的支架之外，所有自行車零
件的圖示皆為示意圖，可能與您的 eBike 有所不
同。
(1)前扣夾 / 活動式
(2)後扣夾 / 固定式
(3)帶 USB 保護蓋的 USB 連接埠
(4)釋放裝置
(5)SmartphoneGrip 固定座
(6)卡鉤
(7)插座式接點
(8)SmartphoneGrip 接點
(9)LED 狀態指示燈
(10)感應式充電線圈
(11)螢幕固定座固定螺栓
(12)固定板
(13)鎖定軸針
(14)內六角扳手
(15)智慧型手機
(16)轉接器外殼
技術性數據
SmartphoneGrip
產品代碼 BSP3200USB 連接埠充電功率 W5 W（1 A@5 V）
無線充電功率 W7.5 W（1.5 A@5 V）
效率 > 67 %工作溫度 °C–5 ... 40儲藏溫度 °C10 ... 40防護等級 IP54重量約： g75安裝
安裝 SmartphoneGrip（請參考圖A）
若要裝上 SmartphoneGrip，請按住釋放裝置(4)不
放。請將 SmartphoneGrip 的上緣裝在螢幕支
架(5) 的卡鉤 (6) 上➊。請將 SmartphoneGrip 往
您的方向拉並將 SmartphoneGrip 按壓至螢幕支架
上 ➋。請鬆開釋放裝置 (4)。
若要取下 SmartphoneGrip，請按下釋放裝置 (4)
並同時將其向您的方向拉➊。請將 SmarthoneGrip
抬起並鬆開釋放裝置 (4) ➋。
Bosch eBike Systems0 275 008 3SG | (20.12.2021)
繁體中文 – 2插入固定板（請參考圖B）
請從下方將固定板 (12) 推入轉接器外殼 (16)，直
到清楚聽見固定板 (12) 卡入的聲音。
從現在起，若非透過鬆開兩個固定螺栓 (11) 將螢幕
固定座 (5) 從轉接器外殼 (16) 拆下，將無法再將
SmartphoneGrip 從螢幕固定座 (5) 上抬起。
提示：固定板 (12) 並非防盜裝置。
安裝智慧型手機（請參考圖C）
SmartphoneGrip 可以容納以下尺寸的手機：
67–88 mm
6,8–13 mm
123–175 mm
此處標明的尺寸包含殼套。不得裝入裝有翻蓋式殼
套的手機。
總重量不得超過 276g。
請將前扣夾 (1) 向前拉➊。請將智慧型手機 (15) 的
長邊靠在固定式卡扣 (2) 上➋。請放開前扣夾並將
智慧型手機 (15) 置中放置在 SmartphoneGrip
上➌。
u裝上智慧型手機時請注意您的手指不會被活動式
扣夾和 SmartphoneGrip 夾住。
安裝智慧型手機後，請確保智慧型手機即使震動也
不會接觸到任何自行車上的固體部分。這可能會造
成智慧型手機永久性損壞。
安裝鎖定軸針（請參考圖D）
若要拆下鎖定軸針(13)，請使用內六角扳手
（1.5mm）(14) 旋出防鬆螺栓 ➊ 並取下鎖定軸針
(13) ➋。
若要裝上鎖定軸針 (13)，請將鎖定軸針 (13) 推入
為其所設的開口中並使用內六角扳手（1.5mm）
(14) 將鎖定軸針旋緊。
提示：鎖定軸針並非防盜裝置。鎖定軸針可防止
SmartphoneGrip 從支架上被快速取下。鎖定軸針
對智慧型手機沒有任何作用
提示：切勿在未看管的情況下將智慧型手機留在
SmartphoneGrip 上！
使用
開始使用
請將智慧型手機裝入 SmartphoneGrip。
請開啟 eBike Flow 應用程式，以查看行車資料。
視智慧型手機的作業系統而定，可免費
從 Apple App Store 或 Google Play
Store 下載 eBike Flow 應用程式。
請用您的智慧型手機掃描該二維條碼，
以下載 eBike Flow 應用程式。
為智慧型手機充電
智慧型手機在 SmartphoneGrip 上時，可以在顯示
行車資料的同時充電。若您的智慧型手機支援感應
式充電功能，您可以為智慧型手機進行無線充電。
無線充電
將具備無線充電功能的智慧型手機裝入
SmartphoneGrip 時，充電程序會自動開始。LED
狀態指示燈 (9) 將亮起黃燈。智慧型手機充滿電
時，LED 狀態指示燈 (9) 會持續亮起綠燈。
將智慧型手機從支架拿起時，充電電壓即會切斷。
透過 USB 充電
若您的手機不支援感應式充電功能，您可以透過
USB 連接埠 (3) 為智慧型手機充電。為此請打開
USB 保護蓋並將一條另外的 USB 連接線（未含於
供貨範圍中）連接至 Micro-AB USB 插孔上。
購買 USB 連接線時請注意您智慧型手機所需的接頭
類型。
狀態指示
LED 狀態指示燈 (9) 會透過各種顏色和燈光模式顯
示以下狀態：
狀態 行為
透過 USB 充電 LED 亮起藍燈。
開始無線充電 LED 閃爍黃燈 3 次。
無線充電 LED 亮起黃燈。
已充滿電 LED 亮起綠燈。
無線充電警示 LED 閃爍紅燈。
以下警告狀態將被偵測並導致無線充電中斷：
– 偵測到異物，例如硬幣、鑰匙或其他金屬物件
– 溫度警示
溫度 >78 °C 時會自動切斷充電程序。溫度降至
56°C 以下時會繼續充電程序。
– 電壓大於 6V 時的過電壓警示
– 電壓小於 4.2V 時的低電壓警示
保養和服務
保養和清潔
清潔時請使用柔軟且僅以清水潤濕的布。請勿使用
任何清潔劑。
u所有維修作業均應由授權的自行車經銷商執行。
所有機件皆不得以高壓水清洗。
搬運
u將 eBike 攜帶於車外，例如放置在汽車車頂行李
架時，請將 SmartphoneGrip 及 eBike 電池取
下，以避免造成損傷。
0 275 008 3SG | (20.12.2021)Bosch eBike Systems
繁體中文 – 3顧客服務處和顧客諮詢中心
若有任何 eBike 系統及其機件的相關問題，請洽詢
授權的自行車經銷商。
授權自行車經銷商的聯絡資訊可於網頁
www.bosch-ebike.com 取得。
廢棄物處理
驅動單元、車載電腦，包括控制單元、
電池、車速感測器、配件以及外包裝均
應以符合環保要求的方式進行資源回
收。
請您自行確保個人資料均已從設備上刪除。
請勿將 eBike 及其機件作為一般垃圾丟棄！
請將無法再行使用的 Bosch eBike 零件帶到授權自
行車經銷商處免費處理。
保留修改權。
Bosch eBike Systems0 275 008 3SG | (20.12.2021)
Other manuals for BSP3200
2
Table of contents
Other Bosch Telephone Accessories manuals
