Bosch DWB068G60I User manual

3FHJTUFS
ZPVS
OFXEFWJDFPO
.Z#PTDIOPXBOE
HFUGSFFCFOFGJUT
CPTDIIPNFDPN
XFMDPNF
Instruction manual
Extractor hood
DWB068G50I, DWB098G50I, DWB068G60I, DWB098G60I, DIB098G50I, DIB128G50I,
DIG098G50I

en
3
Table of contents
Instruct ion manual
(Important safety information . . . . . . . . . . . . . . . 3
7Environmental protection . . . . . . . . . . . . . . . . . . 5
Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmentally-friendly disposal . . . . . . . . . . . . . . . . . 5
ÇOperating modes . . . . . . . . . . . . . . . . . . . . . . . . . 6
Exhaust air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Air recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1Operating the appliance . . . . . . . . . . . . . . . . . . . 6
Switching the appliance on and off . . . . . . . . . . . . . . . 6
Intensive setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Run-on function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2Cleaning and maintenance . . . . . . . . . . . . . . . . . 7
Cleaning agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing and installing the filter . . . . . . . . . . . . . . . . . 8
_Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . 10
4Customer service . . . . . . . . . . . . . . . . . . . . . . . . 11
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.bosch-home.com
(Important safety
information
Impor t ant saf et y informat i on Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8years old and are
being supervised.
Keep children below the age of 8years old at
a safe distance from the appliance and power
cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
:Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.

en Important safety information
4
:Warning – Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the room
if the appliance is being operated in exhaust
air mode at the same time as room air-
dependent heat-producing appliance is being
operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coal-
operated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and discharge
the exhaust gases into the open air through an
exhaust gas system (e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from the
kitchen and neighbouring rooms - a partial
vacuum is produced if not enough fresh air is
supplied. Toxic gases from the chimney or the
extraction shaft are sucked back into the living
space.
■Adequate incoming air must therefore
always be ensured.
■An incoming/exhaust air wall box alone will
not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heat-
producing appliance is installed does not
exceed 4Pa (0.04mbar). This can be
achieved when the air needed for combustion
is able to enter through openings that cannot
be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other
technical means.
In any case, consult your responsible Master
Chimney Sweep. He is able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures to
you.
Unrestricted operation is possible if the vapour
extractor hood is operated exclusively in the
circulating-air mode.
:Warning – Risk of fire!
■Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least once a
month.
Never operate the appliance without the
grease filter.
Risk of fire!
■Grease deposits in the grease filter may
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heat-
producing appliance for solid fuel (e.g.
wood or coal) unless a closed, non-
removable cover is available. There must
be no flying sparks.
Risk of fire!
■Hot oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk of fire!
■When gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk of fire!
■Operating several gas burners at the same
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner of
more than 5kW (wok) is equivalent to the
power of two gas burners.
:Warning – Risk of burns!
The accessible parts become very hot when in
operation. Never touch hot parts. Keep
children at a safe distance.
:Warning – Risk of injury!
■Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk of injury!
■Items placed on the appliance may fall
down. Do not place any objects on the
appliance.
Risk of injury!
■The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100seconds.

Environmental protection en
5
:Warning – Risk of electric shock!
■A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk of electric shock!
■Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the after-
sales service.
Risk of electric shock!
■Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage from returning condensate.
Install the exhaust duct in such a way that it
falls away from the appliance slightly
(1° slope).
7Environmental protection
En v i r o n ment al pr ot ec t i on Your new appliance is particularly energy-efficient.
Here you can find tips on how to save even more
energy when using the appliance, and how to dispose
of your appliance properly.
Saving energy
■During cooking, ensure that there is a sufficient
supply of air to enable the extractor hood to work
efficiently and with a low level of operating noise.
■Adjust the fan speed to the amount of steam
produced during cooking. Only use intensive mode
when required. The lower the fan speed, the less
energy is consumed.
■If cooking produces large amounts of steam, select
a higher fan speed in good time. If the cooking
steam has already spread around the kitchen, the
extractor hood will need to be operated for longer.
■Switch off the extractor hood if you no longer require
it.
■Switch off the lighting if you no longer require it.
■Clean and (if required) replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
■Put the lid on to reduce cooking steam and
condensation.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.

en Operating modes
6
ÇOperating modes
Oper at i ng modes Exhaust air mode
Note: The air must not be discharged into a flue that is
used for exhausting fumes from appliances burning gas
or other fuels (not applicable to appliances that only
discharge the air back into the room).
■Before conveying the exhaust air into a non-
functioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
■If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Air recirculation
Note: To bind odours in air recirculation mode, you
must install an activated carbon filter. The different
options for operating the appliance in air recirculation
mode can be found in the brochure. Alternatively, ask
your dealer. The required accessories are available
from specialist retailers, from customer service or from
the Online Shop.
1Operating the appliance
Oper at i ng the appl i anc e These instructions apply to several appliance variants.
It is possible that individual features are described
which do not apply to your appliance.
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Control panel
Switching the appliance on and off
Switching on the appliance
Press button 1.
The extractor hood starts at fan setting 1.
Selecting the fan setting
Press the 2yor 3=button to set the corresponding fan
setting.
Switching off the appliance
Press the #button.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
1. To activate intensive mode, press and hold the
3=button for 2seconds.
To confirm the setting, the #button lights up and
the 3=button flashes.
2. To end intensive mode early, press the #button.
Note: Intensive mode runs for 10 minutes.Once this
time has elapsed, the appliance switches back to the
fan setting that was last selected.
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
The air which is drawn in is cleaned by
the grease filters and an activated
carbon filter, and is conveyed back into
the kitchen.
Explanation
DSwitches off the fan
1 Fan setting 1
2yFan setting 2/Run-on function
3=Fan setting 3/intensive mode
BSwitches the lighting on/off

Cleaning and maintenance en
7
Run-on function
The run-on function allows the extractor hood to
continue running for a few minutes after it has been
switched off. This eliminates any remaining cooking
smells. The extractor hood will then switch itself off
automatically.
Switching on
1. Press and hold the 2ybutton.
2. Press the button for the required fan setting 1, 2y
or 3=.
The Dbutton and the button for this fan setting
flash.
Notes
■The run-on time for all fan settings is 30 minutes.
Once this time has elapsed, the ventilation system
switches off automatically.
■The fan setting can be changed during the run-on
time by pressing and holding the required power
level.
Switching off
Press and hold the 2ybutton.
The fan run-on will end before the remaining run-on time
has elapsed.
Lighting
The lighting can be switched on and off independently
of the ventilation system.
Switching on or off
Press the Bbutton.
2Cleaning and maintenance
Cl eani ng and mai nt enance :Warning – Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:Warning – Risk of electric shock!
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the circuit
breaker in the fuse box.
:Warning – Risk of electric shock!
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
:Warning – Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
■Harsh or abrasive cleaning agents,
■Cleaning agents with a high alcohol content,
■Hard scouring pads or cleaning sponges,
■High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the
cleaning agents.
Area Cleaning agent
Stainless steel Hot soapy water:
Clean with a dish cloth and then dry with a
soft cloth.
Clean stainless steel surfaces in the grind
direction only.
Special stainless steel cleaning products are
available from our after-sales service or from
specialist retailers. Apply a very thin layer of
the cleaning product with a soft cloth.
Painted surfaces Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plastic Glass cleaner:
Clean with a soft cloth.
Glass Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Controls Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Risk of electric shock caused by penetrating
moisture.
Risk of damage to the electronics from pene-
trating moisture. Never clean operating con-
trols with a wet cloth.
Do not use any stainless steel cleaners.

en Cleaning and maintenance
8
Removing and installing the filter
The filter must be serviced regularly in order to
guarantee efficient filtration of odours and grease.
Metal grease filter
The metal grease filters must be cleaned every
20operating hours or at least every 2weeks.
:Warning – Risk of fire!
Fatty deposits in the grease filter may catch fire.
Clean the grease filter at least every 2weeks.
Never operate the appliance without a grease filter.
Removing metal grease filter
:Warning – Risk of injury!
The metal grease filters and components inside the
appliance may have sharp edges. Wear protective
gloves.
:Warning – Risk of injury!
The metal grease filters are very heavy. Remove the
metal grease filters carefully and secure them against
falling down when doing so.
1. Open the lock and swing the metal grease filter
down.
Notes
– When you do this, take hold of the metal grease
filter from underneath with your other hand. Make
sure that the metal grease filter does not fall and
damage the hob.
– Fat may accumulate in the bottom of the metal
grease filter. Hold the metal grease filter level to
prevent fat from dripping out.
2. Clean the metal grease filters.
3. Clean the inside of the appliance.
Cleaning the metal grease filters
:Warning – Risk of fire!
Fatty deposits in the grease filter may catch fire.
Clean the grease filter at least every 2weeks.
Never operate the appliance without a grease filter.
Notes
■Do not use any aggressive, acidic or alkaline
cleaning agents.
■When cleaning the metal grease filters, also clean
the holder for the metal grease filters in the
appliance using a damp cloth.
■The metal grease filters can be cleaned in the
dishwasher or by hand.
By hand:
Note: You can use a special grease solvent for
stubborn dirt. It can be ordered via the Online Shop.
■Soak the metal mesh grease filters in a hot soapy
solution.
■Clean the filters with a brush and then rinse them
thoroughly.
■Leave the metal mesh grease filters to drain.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has
no effect on the function of the metal mesh grease
filters.
■Do not clean heavily soiled metal mesh grease filters
together with utensils.
■Place the metal mesh grease filters loosely in the
dishwasher. The metal mesh grease filters must not
be wedged in.
Installing the metal grease filter
With the lock facing the front, insert the metal grease
filter into the underside of the appliance and engage the
lock.
Note: When pushing the filter in, make sure the lock
engages. Otherwise, the metal grease filter may fall and
damage the hob.

Accessories en
9
Changing the active carbon filter (only in circulating-
air mode)
To ensure effective odour removal, the filters must be
serviced regularly.
The active carbon filters must be replaced at least every
4months.
Note: The active carbon filters cannot be cleaned or
reactivated.
1. Remove the metal grease filters, see above.
2. Push back the fastening hooks.
3. Remove the old active carbon filter.
4. Insert the new active carbon filter and secure it in
place using the fastening hooks.
5. Fit the metal grease filters.
_Accessories
Ac c es s o r i e s Special accessories
Note: Special accessories are not included in the
delivery. Special accessories can be purchased from
our after-sales service, from specialist retailers, or
online.
--------
Accessory Order number
Recirculation Kit - DWBxxxxxx / DWGxxxxxx
(1x active carbon filter, back flap, clamping
ring)
DHZ5467
Active Carbon Filter DHZ5477
Flue Duct Extension With Bracket - DWBxxxx-
50I / DWGxxxx50I
DHZ5640
Flue Duct Extension With Bracket - DWBxxxx-
60I / DWGxxxx60I
DHZ5469
Ducting Kit DHZ5468

en Trouble shooting
10
3Trouble shooting
Tr oubl e shoot i ng Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
:Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Replacing the LED lights for DIB098G50I,
DIB128G50I and DIG098G50I
Defective LED lights may be replaced by the
manufacturer, their after-sales service or a qualified
technician (electrician) only.
Replacing the LED lights for DWB068G50I,
DWB098G50I, DWB068G60I and
DWB098G60I
:Warning – Risk of electric shock!
When changing the bulbs, the bulb socket contacts are
live. Before changing the bulb, unplug the appliance
from the mains or switch off the circuit breaker in the
fuse box.
:Warning – Risk of injury!
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly
into the switched on LED lights for longer than
100seconds.
Important! Only use bulbs of the same type and
wattage.
1. Allow the bulb to cool down.
2. Undo the screw that fastens the bulb cover.
3. Remove the bulb cover.
4. Remove the bulb and replace it with a bulb of the
same type.
5. Replace the bulb cover and screw it on tightly.
6. Plug in the mains plug and switch the fuse back on.
Replace the bulb with one of the same type:
Voltage: 230 V
Power: Max. 2 W
Thread: E14
Malfunction table
--------
Problem Possible cause Solution
The appliance
does not work
The plug is not
plugged in.
Connect the appliance to the
electricity supply
Power cut Check whether other kitchen
appliances are working
Faulty fuse Check in the fuse box to make
sure that the fuse for the appli-
ance is OK
The lighting does
not work.
The bulbs are
faulty.
For information on changing
the bulbs, see the "Replacing
Bulbs" section.

Customer service en
11
4Customer service
Cu s t o mer ser vi ce When calling us, please give the product number (E
no.) and the production number (FD no.) so that we can
provide you with the correct advice. The rating plate
with these numbers can be found inside the appliance
(remove the metal grease filter to gain access).
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
E no. FD no.
After-sales serviceO

*9001451897*
9001451897
990926
BSH Household Appliances Manufacturing Pvt. Ltd.
Arena House, 2nd Floor Main Building
Plot No.103, Road No.12
MIDC, Andheri East,
Mumbai-400093
www.bosch-home.com