BOSSCO Hyper Fuzz FZ-2 User manual

UBOSS
F22,
Instructions
Thank
you
for
purchasing
the
BOSS
FZ-2
HYPER
FUZZ.
To
make
the
best
use
of
the
unit,
please
read
the
instructions
carefully.
-Despite
its
compact
size,
this
effect
unit
packs
two
kinds
of
fuzz
providing
characters
that
are
quite
different.
It
also
provides
gain
boosting
based
on
a
discrete
architecture.
-While
recreating
the
traditional
fuzz
sound,
this
unit
also
generates
a
distortion
that
could
be
described
as
contemporary
and
convivial.
~Two
tone
controls
allows
the
sound
to
be
adjusted
until
you
have
precisely
the
sound
you
need.
a
AC & BATTEAY
POWERED

PANEL DESCRIPTION
€ ourput INPUT €
HYPER
Fuzz
FZ-2
OBOSS
CONNECTIONS
Amplifier
1 AC Adaptor Jack
Connect an AC adaptor ( BOSS PSA-120, 220
or 240 depending on the line voltage system
in your country } to this jack.
* An AC adaptor allows long and secure operation
without worrying about battery life.
* Be sure to use a BOSS PSA-120, 220 or 240
adaptor.Use of any other adaptor may damage the
device.
}— 11 2 Check Indicator
Lights up when the effect is ON, allowing you
to confirm whether the effect is ON or OFF.
* This indicator also serves as the Battery Check
indicator. You will know when the battery has
worn down and needs to be replaced whenever
this indicator goes dim or no longer lights.
3 Level Knob
Used to adjust the volume level of the sound
while the effect is applied. Should be adjusted
so there is no noticeable difference between
the times when the effect is applied and when
the sound is normal.
Connect the AC Adaptor
qui
aoe
4
* Inserting a plug into the Input Jack will
automatically switch the unit on.
* Before connecting or disconnecting a plug,
make sure that the volume of the amplifier is
turned down.
* When the Mode knob is switched to Gain
Boost, this knob will not provide its normal
function.
* With this knob turned all the way to the left,
no sound will be output.
Tone Knob (Treble)
Allow the higher frequency portions to be
boosted/cut. At the center, the tone will be
flat. Boost the higher frequencies by turning
it towards the right (hk ). Turn toward the
left ( 1) to cut them.
Tone Knob (Bass)
Allow the lower frequency portions to be
boosted/cut. At the center, the tone will be
flat. Boost the lower frequencies by turning
it towards the right ( ts }. Turn toward the
left (x8 ) to cut them.
Output Jack
The output from this jack can be connected
to your amp or to another effects device.
AC Adaptor:
BOSS PSA-120,
220 of 240 (option)
7 Pedal Switch
Used to switch effects ON or OFF.
8 Thumb screw
Loosen the screw to open the cover for battery
replacement. For a detailed explanation, see
"BATTERY REPLACEMENT"
9 Mode Selection Knob
Allows you to select the function you wish
your FZ-2 to perform.
FUZZ 1 A basic fuzz sound that places
emphasis on the harmonics.
FUZZ 2 A full-bodied fuzz sound that
places emphasis on the lower
frequency range.
GAIN BOOST Ideal for boosting the power of
a guitar with limited output
power (such as one with a
single-coil pickup); or for
increasing the amount of
distortion you can obtain when
using a distortion-type effects
units or guitar amplifier.
10 Gain Knob
[When FUZZ 1 or FUZZ 2 is selected]
Allows you to adjust the depth of the fuzz. The
distortion depth is increased (and sustains will
be lengthened) as you move the knob to the
right").
{When GAIN BOOST is selected}
Allows you to adjust the amount by which the
gain is to be boosted. The gain is increased the
more you move the knob to the right (. *).
* Oscillation could be produced if the depth is
increased too much.
11 Input Jack
Here is where you need to connect your
guitar, or other electric/electronic instrument.
* The Input Jack is equipped with a power switch,
Whenever you insert a plug into it, the power is
turned ON. Pull the plug out, and the power goes
OFF. For this reason, try to make a habit of pulling
out the cord going to the Input Jack whenever the
pedal is not being used.

SAMPLE SETTINGS
A basic fuzz sound.
The most orthodox fuzz sound.
Light fuzz sound.
A buoyant fuzz sound with a notably
warm tone.
Gain Booster Mode
Treble fuzz sound.
A truly radical sound with an upper
range that is garish and dazzling.
Fat fuzz sound.
A fat fuzz sound that favors the treble
end.
These settings allow a guitar amp to be driven to the full.
Ce Ee
Bitaterete) aeTatereTaYe| et ar
Amplifier
ite Guitar
Treble booster.
‘Emphasizes the upper range.
Bass booster.
Emphasizes the lower range.
* The Level knob cannot be used while the
unit is in the Gain Booster mode.
These settings produce a really powerful distortion. The unit should be
connected so it is located before a distortion-type effects unit.
|
Amplifier
OBOSS |
OD-2 or other distortion-
type effects unit.

OPERATION
For FUZZ 1 or FUZZ 2:
1
Once you have all the
connections made, set the
knobs on the panel so they
conform to the illustration
below,
* Have the Mode knob set to
either FUZZ 1 or FUZZ 2.
* Before connecting or
disconnecting any instrument,
make sure that the volume of
the amplifier is turned down,
2 Step on pedal switch (7) to
turn ON the effect. (The
Check indicator will light.)
4 Adjust both the BASS and
TREBLE Tone knobs (5 & 4)
until you have the tone you
desire.
ka j
Reve TONE OAN tn
ona © % woe
cur
Use the Gain knob (10) to
adjust the amount of
distortion. The distortion
depth is increased as you
move the knob to the right.
* Oscillation could be produced
if the depth is increased too
much,
Adjust the Level Knob (3) so
there is no noticeable
difference between the times
when the effect is applied
and when the sound is
For GAIN BOOST:
1
2 Step on pedal switch (7) to turn ON the effect.
When set to this mode, the Level knob (3) will
not provide its normal function.
Once you have all the connections made, set
the knobs on the panel so they match the
illustration below.
* Have the Mode knob set to GAIN BOOST.
(The Check indicator will light.)
you move the knob to the right.
* Oscillation could be produced if the depth is increased
too much.
CHECK
O
3 Use the Gain knob (10) to adjust the amount by
which to boost the gain. The gain is increased as
4 Adjust both the BASS and TREBLE Tone knobs
{5 & 4) until you have the tone you d esire.

BATTERY REPLACEMENT
(1) Loosen the thumb screw on the pedal to
open it.
(2) Take out the battery from the battery
housing and disconnect the battery snap.
(3) Connect a new battery to the battery snap,
then replace the battery in to the battery
housing,
* Make sure that the polarity of the battery
is correct,
(4) Push the coil spring into the spring base on
the rear of the pedal, then close the pedal.
* Make sure that the snap cord is not caught
in the pedal or coil spring.
(5) Insert the thumb screw into the guide bush
hole and firmly tighten the screw.
The type of battery to use is: 006/9 V (one).
Pedal
Battery Snap Cord
Thumb Screw
Housing
SETTING MEMO
IMPORTANT NOTES
-Do not subject the unit to temperature extremes
{eg. direct sunlight in an enclosed vehicle). Avoid
using or storing the unit in dusty or humid areas or
areas that are subject to high vibration levels.
-Remove the battery whenever the unit is not going
to be used for an extended period of time.
-When operating solely on a battery, the unit's
indicator becomes dim when the battery is
depleted. Replace the batlery immediately.
~if there is a battery in the unit while an AC adaptor
is being used, normal operation will continue
should the line voltage be interrupted(power
blackout) or the power cord become
disconnected.
-Should a malfunction occur (or if you suspect there
is a problem) discontinue use immediately. Contact
qualified service personnel as soon as possible.
wes
@OUT:9VDC/200mA
CHECK
Gani
CHECK
eas
CHECK
a
CHECK
cain
finer
BOOST
BOOST
BOOST
LEVEL
TONE
—
GAIN
fuzz)
LEVEL
TONE
GAIN
pmi"
TONE
—
GAIN
puzi
LEVEL
TONE
GAIN
pur"
cir
BOÔST
MN
MAX
MODE
tie
Max
MAX
CÜT
soost
MIN
MAX
MODE
MIN MAX
BOÒST
MIN
MAX
MODE
(TREBLE
(S-TREBLE
(TREBLE
BASS
BASS
BASS
CHECK
an
CHECK
angi
CHECK
oan
CHECK
aan
O
pera
hor
BOOST
BOOST
LEVEL
TONE
—
GAIN
ruzi
LEVEL
TONE
GAIN
puzzi
LEVEL
TONE
GAIN
pus
`
LEVEL
TONE
—
GAIN
rug”
p
'
i
Ñ
j
`
k
WIN
MAX
CUT
BOOST
MIN
MAX
MODE
WIN
MAX
CUT
BOOST
MIN
MAX
MODE
MN
MAX
CUT
BOOST
MIN
MAX
=
MODE
MIN
MAX CUT
BOOST
MIN
MAX
MODE
TREBLE
(TREBLE
(©—TREBLE
(TREBLE
BASS
BASS
BASS
BASS

Roland’
26050977
UPG
i
28050977
| e902
SPECIFICATIONS
Controls
:
Pedal
Switch,
Mode
Selector
Switch,
Gain,
Tone(Treble,
Bass),
Level
Indicator
:
Check
Indicator(Serves
also
as
battery
check
indicator)
Jacks : Input,Output,AC Adaptor
Input Impedance : 1MQ
Output Impedance : 1kQ
Recommended Load Impedance : 10k or greater
Residual Noise : -70dBm(IHF-A, Typ.)
Power Supply : DC9V; battery ( 9V ), AC Adaptor (PSA Series : Option)
Current Draw : 16mA (DC9V)
Dimensions : 70 (W) x 125 (D) x 55 (H) mm / 2-3/4" x 4-15/16" x 2-3/16"
Weight : 420g / 15 oz (including battery)
Accessories : Instructions, Battery S-OO6P/9V (6F22/9V) x 1
Options
:
AC
Adaptor
PSA-120,
PSA-220, PSA-240,
Battery
S-O06P/9V,
6AM6/9V
(Alkaline)
The
specifications
for
this
product
are
subject
to
change
without
prior
notice.
Products of Roland
Printed in Taiwan ‘93-10-D3-11C