Bowens Streamlite 330 User guide

Owner’s Han book

All Bowens electrical products are covered by a two year
warranty against any faulty design, materials and
workmanship.
If a product does not work on arrival or up to a maximum
period of four weeks from the date of purchase, it should be
returned to the dealer/retail outlet from where it was
purchased, to exchange (if available) the faulty unit for a new
one; if the faulty unit was part of a kit that was purchased, the
dealer / retailer may choose to simply replace the unit and not
the entire kit. Alternatively the dealer may offer to repair the
unit as soon as possible at no charge.
If neither an exchange or repair is possible for the faulty unit,
then a full refund may be made.
If a warranty fault occurs after the initial four week period (and
within the max two year warranty period), then the unit should
be returned to the dealer, who will arrange to repair the unit
as soon as possible, at no charge.
This warranty does not apply to consumable items such as
flash tubes, modelling lamps, fuses, consumable type
batteries.
Should a unit be returned at any time within the two year
warranty period, and it is judged to have experienced any of
the following points, failure to follow working instructions
correctly, accidental or willful damage, misuse, alteration or
repair by a non authorised Bowens service / repair centre,
then the warranty will be deemed invalid and any repairs that
may need carrying out will be payable by the owner.
The cost of any repairs should be notified to the owner, by the
dealer, in advance of undertaking any work that may be
required.
No warranty repairs can be undertaken to any units without
proof of purchase.
All warranty repairs or returns must be conducted with the
dealer from where the product was purchased.
ther terms and conditions may be applicable in specific
countries, if stated by the dealer at the time of purchase.
Contents
All Bowens products are certified by the CE mark. The CE certified mark is a
declaration of conformity to the required EEC directives 89/336/EEC
‘Electromagnetic Compatibility’ and 73/23/EEC ‘Low Voltage Directive’.
warranty
Warranty 2
CE Mark 2
Intro uction 3
Safety Notes 3
Streamlite 330 4
Streamlite 530 5
Operation 6
Operation 7
Cocoon & 7
Cocoon Stan Assembly

3- Streamlite | In roduc ion & Safe y No es.
introduction
Thank you for choosing the Streamlite from
Bowens. The Streamlite has been designed by
working closely with photographers to develop a
continuous light source that meets the high-
quality standards required in todays professional
studios.
In order to obtain the full benefit from your
purchase, please take a few moments to
familiarise yourself with this user manual.
For more information on all Bowens products and
to find details of your nearest Bowens dealer,
please visit the Bowens website.
www.bowens.co.uk
safety notes
• Switch power off and disconnect from the power supply
before changing a lamp or fitting removing accessories.
• Disconnect the power supply before changing the fuse.
Never replace with a fuse of a different rating.
A spare fuse is fitted in the fuse holder under the AC inlet
(see pages 4-5).
• Exercise care when handling equipment that has been in
use.
• Avoid placing cables where they can be tripped over.
Protect from heavy, sharp or hot objects, which may
cause damage & replace damaged cables immediately.
• Always remove the power cord by gripping the plug.
NEVER pull the cord.
• Always ensure that any extension cord used has a
suitable current rating to prevent overheating and never
use coiled extension cords.
• Use the specified lamps. A fire hazard exists if lamps
other than the ones specified are used.
• Use in an environment where moisture or flammable
vapour is likely to come in contact with the unit.
• Restrict air vents while in use.
• Use a unit with damaged housing, mouldings or
lamp. If the unit is dropped or damaged in any way,
always have it checked before using.
• Use any equipment with a damaged mains cable.
• perate the unit without a safe grounded AC supply.
always... never...

4- Streamlite | 330
Streamlite 330
30W spiral lamp
Reflector
Carry handle
AC power input
n/ ff switch
Adjustable stand
bracket
Maximum Power 90W (3 x 30W)
Lamps 230V 30W E27 5600K BW-3457
117V 30W E27 5600K BW-3458
Supply Voltage 230V 220-240V 50/60Hz
117V 110-130V 50/60Hz
Dimensions 414mmØ x 325mm inc re lector
161⁄3”Ø x 124⁄5”inc re lector
Weight 1.95Kg (4.2lbs) inc re lector
Specifications:
117V 230V
Streamlite 330 BW-3455 BW-3450
Streamlite 330 kit BW-3475 BW-3470
Streamlite 330 di user BW-3456 BW-3456
Part Co es:

30W spiral lamp
Reflector
Carry handle
Lamp n/ ff
switch
AC power input
Power n/ ff
switch
Adjustable stand
bracket
5- Streamlite | 530
Streamlite 530
Maximum Power 150W (5 x 30W)
Lamps 230V 30W E27 5600K BW-3457
117V 30W E27 5600K BW-3458
Supply Voltage 230V 220-240V 50/60Hz
117V 110-130V 50/60Hz
Dimensions 460mmØ x 335mm inc re lector
181⁄10”Ø x 131⁄5”inc re lector
Weight 2.8Kg (6.17lbs) inc re lector
Specifications:
117V 230V
Streamlite 530 BW-3465 BW-3460
Streamlite 530 di user BW-3466 BW-3466
Part Co es:

General Operation
• Always use the cable supplied from your
Bowens dealer to connect the unit to the
mains power supply.
• It is recommended to switch on the Streamlite
a few minutes before you start shooting as the
light output will improve after the lamps have
been switched on for a short period.
• When operating the Streamlite angled down
more than 45° below horizontal, heat build up
can shorten the lamp life. If used this way limit
use to around 1 hour then switch off and allow
to cool before recommencing operation.
Replacing Lamps
• Switch FF the power and disconnect from
the mains supply before removing / replacing
any lamps.
• Remove the reflector.
• While holding the lamp by the base, gently
screw the lamp into the lamp holder (as shown
in figure 1).
• Repeat previous step until all lamps are
positioned into the lamp holders (figure 2).
Attaching Reflector
• Position the spigots on the reflector into the
slots on the Streamlite (figure 3).
• Gently turn the reflector clockwise until locked
into place (figure 4).
Note: It is recommended that only lamps purchased
under a Bowens ‘BW’ stock code number are used as
replacements. The manufacturer will not accept liability
for the use of any other lamps.
6- Streamlite | Opera ion
Operation
figure 1. figure 2.
figure 3.
figure 4.

Operation
Attaching Diffuser
• Place the diffuser over one side of the
reflector, as shown below.
• Stretch the elasticated diffuser over the
reflector until appears as shown.
Cocoon Stan Assembly
StepONE - Place the two
leg sections on the floor
with the legs fully
extended.
StepTWO - Attach one of
the Cocoon Supports.
Use the studs on either
side of the support to
lock in place with the leg
sections.
StepTHREE - nce the
studs are locked in place
the first support should
appear as shown.
StepFOUR - Attach both
supports to the legs.
Your assembled Cocoon
Stand should appear as
shown opposite.
Cocoon Assembly
StepONE - Place the
central translucent panel
onto the floor with the
red and blue coloured
dots facing upwards.
StepTWO - Fasten the
two side panels using the
attached velcro. Ensure
coloured dots on each
panel line up to the
correct sides.
StepTHREE - Attach the
final panel as shown.
Make sure all coloured
dots are correctly placed.
StepFOUR - Finally, zip
all of the panels together.
Your assembled Cocoon
should appear as shown.
Cocoon & Cocoon Stand Assembly
7- Streamlite | Opera ion
ONE
TWO
THREE
FOUR
ONE
TWO
THREE
FOUR

BWL0575 | S reamli e 330 and 530 07/2010
Owner’s Han book