Boyel Living A3794 User manual

1. When you open the product packaging, please check the product and accessories at first.
If there are any discrepancies, please contact us promptly. We will provide you with a
satisfactory solution.
2. The hot and cold water supply pipe of the valve must be properly connected. When facing the
front of the valve, the hot water supply is on the left and cold water supply is on the right.
Incorrect connection will cause permanent damage to the cartridge.
3. If the accessories to be changed without affecting the use, we will not make a prior notice.
4. The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5. The water pressure of the faucet is 0.05MPa-1.0MPa(including cold water and hot water
Pressure). Applicable water temperature range:39°F-194°F.
CARE INSTRUCTIONS
DO NOT:
A
A-1
A-2
A-3
A-4
A-5
B
C
D
E
No. Description
Pressure balanced diverter valve
Valve
Face plate with sealjoint
Diverter knob kit
Trim cap
Allen screw
Hand shower
Head shower
Flexible hose
Shower arm and flange kit
Firmly hand tighten the hose
to the valve and add a quarter
turn using the proper wrench
Tighten more if needed
CONNECTION ADVICE Plumber's
putty Thread seal
tape
Included
2、PREPARATION BEFORE INSTALLATION
1、INSTALLATION PRECAUTIONS
3 CONCEALED FAUCET ACCESSORIES LIST、
4、TECHNICAL DRAWING OF DRILING SIZE
SHOWER SYSTEM FAUCET
Installation instruction
A3794
CH/BN/MB/BG/ORB
Website:www.boyellivng.com
Customer Service：: 323-982-8955
Email: [email protected]
* Apply plumber's
putty under the plastic
cover deck plcta to seal
your installation.
*The model shown in
the installation steps
may differ from the one
in box however
connection type and
installation steps are
the same.
1. The size of the embedded box that needs to be drilled is 6"*6".
2、 The depth of the embedded box is 1.8"-2.4".It's better to drill the depth of 1.8"for
blank wall.
E1
E2E4
E5
E
D
C
A
E3
B
SHOWER
Hot
water
Cold
water

7、THE PROCEDURE OF SEALING THE WALL
8、INSTALLATION OF CONTROL VALVE
6、WATER TESTING AND SEALING TESTING
5、PIPE CONNECTION 9、SHOWER SETS INSTALLATION / HANDLE SHOWER INSTALLATION
11. CLEARANCE AND MAINTENANCE
10、PRODUCT REPARATION
1. Please drill the holes on the wall for the main body part, hot and cold water inlet pipes as
well as shower arm connection pipes according to the basic product dimension drawing as
Below.
2. Please make hot and cold water inlet pipe, the mixed water outlet pipe connect with control
valve, and tighten with the wrench.
1. After the pipe connection is completed, open the protective panel and cover, and then open
the cartridge, flush the pipeline;then close the cartridge to check the pressure resistance
and sealing performance of the pipeline, make sure there are no leakage.
2. Block each outlet pipe with a stopper then open the cartridge to check if the pipe joint is
well-sealed and the pipe condition under pressure to ensure no leakage.
Testing Purpose: Flush the impurities and sludge in the pipeline to avoid clogging and affect
the effluent functions.
Use a parallel ruler to measure the flatness of the valve and the vertical wall surface. If the
wall surface is not flat, it should be patched to ensure the valve and vertical wall angle meets
at nearly ideal angle of 90, then lay the tile decoration.
1. Take off the protective panel and cover.
2. The decorative panel and the handle are connected to the control valve as shown below
sequence.
3. According to the figure below, please correctly adjust the direction of water separator
Handle.
If the cartridge is worn out which cause leakage, please turn off the water source. Remove the
handle, panel, and decorative cover in sequence, remove the gland with a wrench, then take
out the cartridge and copper sleeve. Repair or replace the new cartridge, then install it again in
sequence.
In order to keep the faucet appearance smooth and good performance, please follow the below
steps to clean and maintain the faucet.
1. Clean with water and dry with a soft cotton cloth.
2. Use a mild liquid and a colorless glass cleaner to remove surface dirt and scale,
also you can use the cleaner without grinding function.
3. Do not use detergents, polishing tools, abrasive cloth, paper towels or scrapers to
clean the faucet.
4. Do not use acid cleaners, insoluble granular detergents, soaps etc to clean the
Faucet.
SCREW IN
Cold
water
Hot
water
SHOWER