Kohler Components 77984T-9E User manual

1327567-AN2-D 1
1327567-AN2-D 4
INSTALLATION INSTRUCTIONS
COMPONENTSCOMPONENTS
SERVICE PARTS
**Color code must be specified when ordering.
77984T-9E Floor Mount Bath Filler With Handshower77984T-9E Floor Mount Bath Filler With Handshower
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. An inline water filter must be used with this product.
3. Inspect the supply tubing for damage. Replace as necessary.
4. Observe local plumbing codes.
5. The minimum working pressure for the diverter is 0.05MPa(0.5bar).
6. Check for leaks before covering the pipes, repairs as needed.
7. The highest working pressure for handshower is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure
reducer is needed. The highest water and environment temperature is 60ºC. Please keep handshower and
shower arm away from heater, or it may become damaged and cause injury to the user.
8. Please purchase the matched mounting base 97905T-DR when install the faucet.
9. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.
ROUGH-IN DIMENSIONS
*Please purchase the appropriate bathtub according to the dimension.
240
250
Ø28
G1/2˝B
948±10
630 Max.
*70 Min.
Ø160
10º *244
Bathtub
Ø48
Ø29
650±10
844±10
1093±10
95
Ø70
Ø120
Ø26
135
218
47
G1/2˝B
831727**
(For others)
1403178**
880010
880010
77420
1177225
1327565**
1119281
78125
1386906(For BL/BN)
1327564(For others) 1289681
1091126
1384765**
1017949
1087824
74463
1082901
1082901
1084120
1010167
77955
834638
1330683**
1330682**
1343467**
880010
1144498**
1080954
1248781**
(For 2BL&BL)
G1/2˝
G1/2˝
1500
For 2BL&BL For others
G1/2˝
G1/2˝
1500
1384765**
1087824
834404
1416818

1327567-AN2-D 2
1327567-AN2-D 3
2
4
5
6
8
7
1
3
HANDLE OPERATION
Turn the upper handle clockwise for cold water; Turn the lower handle counter-clockwise for hot water.
Lift and turn the diverter for handshower. Turn the diverter in the normal position for bath spout.
INSTALLATION
How to Install the Faucet
Shut off water supply. Cut away the extending
part of the base protector(1) in accordance with
the tile surface. Remove the plug(2) from the
base. Remove the protector(3) from the faucet.
Slide up the escutcheon kit(4). Install the faucet.
NOTE: Keep the faucet vertical to the base, to
avoid damaging the O-rings on the bottom.
Keep the “KOHLER” logo on the body pointing
to tub. Fix the faucet to the base with the
screws(5) and washers(6) through the flange(7).
Tighten the screws with hex wrench(8).
Slide down the escutcheon kit, make sure it is
against the finished floor.
How to Install the Spout
Remove the protector(10) from the spout(9).
Install the spout into the body. Position the
spout. Make sure it is vertical to the handles.
Tighten the screws(11). Insert the plugs(12).
How to Install the Handshower
Remove the protector(10) from the connector
(13) of the diverter kit. Connect the hose(14)
to the diverter kit and handshower(15) with
washers. Tighten all the connections.
Hang the handshower on the bracket(16).
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off position.
Turn on the main water supply, and check for
leaks. Repair as needed.
Remove the aerator(18) by key(17). Remove
the handshower(15). Turn on faucet handle.
Run hot and cold water through spout for
about one minute to remove any debris.
Check for leaks at this time. Remove any
debris. Shut off the faucet. Reinstall the
aerator and handshower.
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
Katalyst Air
Intense Massage
How to Operate the Handshower
Press the buttons of the handshower to
change water flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause the
flow stream to become distorted or reduce the
flow rate. To remove the debris or mineral
build-up, run water through the handshower,
firmly press or rub your finger back and forth
across the rubber nozzles.
Remove and clean the screen washer.
15 16
13
9
10
11
11
12
12
14
15
18
17