B+B SmartWorx 485OPDR User manual

Recommended Accessories
Model MDR-20-24
Power Supply
Model HESP4DR
Data Line Surge Suppressor
Bias is provided by 4.7kΩ pull-up/down resistors on
the Data-In lines. This value is adequate for most
applications without termination. If another value is
required, space is provided on the PC for through-hole
resistor placement (R12, R21, R14, and R23).
For more information on Biasing, see B+B SmartWorx
Application Notes at:
www.bb-elec.com/Learning-Center.aspx
UL Installation Information
Underwriters Laboratories Conditions of Acceptability –
when installed in the end-use equipment, consideration
should be given to the following:
1. The wiring terminals are suitable for factory wiring
only.
2. This device is to be mounted in a suitable enclosure
in the end-product.
3. This device is suitable for operation at a maximum
surrounding air temperature as described in the
documentation.
4. These devices are intended for use in a Pollution
Degree 2 Environment.
• Input Voltage: 10 – 30 VDC
• Input Power: 0.7 Watts
• Wire Range: 12 – 24 AWG
• Tightening Torque: 4 kgf-cm
• Temperature rating of eld installed conductors is
105 °C minimum, sized for 60 °C ampacity.
• Use copper wire only
• Maximum surrounding ambient air temperature 80 °C
Document Number – 710-10765-00_485OPDR_4316qsg
1-888-948-2248 | Europe: [phone]
advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: [phone] | Fax: [phone]
www.advantech-bb.com | E-mail: [e-mail]
Before you begin, be
sure you have the following:
485OPDR
Optically Isolated RS-422/485 Repeater
Fast and easy on the web: www.advantech-bb.com
+ 485OPDR Repeater
+ 10-30VDC, 0.7W Power Supply
+ RS-422/RS-485 Cable
QUICK START
GUIDE
Biasing

SW-7: TX Enable SW-8: RX Enable
RS-485 4-Wire Full Duplex ON OFF
RS-422 Full Duplex OFF OFF
All connections for power and data are made
through screw terminal block connections.
Terminal Block
Connectors
A – F
Terminal Block
Connectors
G – M
DIP
Switches
External Power Supply 10 to 30 VDC
Connections: Ground/V(-) = M V (+) = J
NOTE: Terminal block and DIP switch
settings are shown on the product.
Two sets of DIP switches must be set, one for each side.
Setting the baud rate to 9600 will generally allow you to
communicate with higher baud rates.
For more information, visit www.advantech-bb.com
You can perform a loopback test by connecting either an
RS-232 to RS-422/485 converter or a USB to RS-422/485
converter to the 485OPDR.
Jump L to K and H to G and power the 485OPDR.
Set dip switches to RS-422 or RS-485, depending
upon what you are using to connect to the PC. Set the
baud rate to 9600.
Using HyperTerminal or a similar program, connect to
the appropriate COM port. Remember to set the baud
rate to 9600. Turn off HyperTerminal local echo. Start
typing. If you can see the data you are typing, the
loopback is successful.
SW-7: TX Enable SW-8: RX Enable
RS-485 2-Wire Half Duplex ON ON
RS-485 4-Wire Full Duplex ON OFF
RS-422 Full Duplex OFF OFF
Terminal
Block Signal
A
OUT (+)
ISOLATED
B
IN (+)
C
Protected Ground
D
OUT (-)
E
IN (-)
F
Signal Ground
G
IN (-)
NON-ISOLATED
H
OUT (-)
J
+10 to 30 VDC
K
IN (+)
L
OUT (+)
M
Ground
SWITCH
K Baud (ms) 1 2 3 4 5 6 Timeout
9.6 OFF OFF ON OFF OFF OFF 1.1
SWITCH
K Baud (ms) 1 2 3 4 5 6 Timeout
1.2 OFF OFF OFF OFF OFF OFF 9.02
2.4 ON OFF OFF OFF OFF OFF 4.73
4.8 OFF ON OFF OFF OFF OFF 2.20
9.6 OFF OFF ON OFF OFF OFF 1.1
19.2 OFF OFF OFF ON OFF OFF 0.62
38.4 OFF OFF OFF OFF ON OFF 0.29
57.6 OFF OFF OFF OFF OFF ON 0.17
76.8 OFF OFF OFF ON OFF ON 0.15
115.2 OFF OFF OFF ON ON ON 0.11
RS-422 Full
Duplex OFF
DIP Switches
1
+
Product Overview
Loopback Test
3
Wiring Examples
2