Breckwell SP22 User manual

Exceptional Heat, Outstanding Value
®
BRECKWELL
ECONOMY SERIES SP22
OWNER’S MANUAL
• WARNING:Ifyourapplianceisnotproperlyinstalledahouseremayresult.Foryoursafety,
followtheinstallationdirections.Contactlocalbuildingorreofcialsaboutrestrictionsand
installationinspectionrequirementsinyourarea.
• PLEASE read this entire manual before installation and use of this pellet fuel-burning
roomheater.Failuretofollowtheseinstructionscouldresultinpropertydamage,bodily
injury,orevendeath.
• Savetheseinstructions.
©BRECKWELL HEARTH PRODUCTS
02/09
Manufacturedby
Breckwell Hearth Products
Eugene,Oregon
www.breckwell.com
PROFESSIONALINSTALLATIONISHIGHLYRECOMMENDED
SP22 SP22I

INTRODUCTION
2
Thank you for purchasing the Breckwell Pellet Burning Stove, you are now prepared to burn wood in the most efcient,
convenient way possible. To achieve the safest, most efcient and most enjoyable performance from your stove, you must
do three things: 1) Install it properly; 2) Operate it correctly; and 3) Maintain it regularly. The purpose of this manual is to
help you do all three.
PLEASEreadthisentiremanualbeforeinstallationanduseofthispelletfuel-burningroomheater.Failuretofollow
theseinstructionscouldresultinpropertydamage,bodilyinjuryorevendeath.
Keepthismanualhandyforfuturereference.
This stove has been independently tested to ASTM E1509-04 Standard Specication for Room Heaters, Pellet Fuel Burn-
ing Type 1, ULC/ORD 1482-90 Standard for Solid Fuel Room Heaters, and Oregon Administrative Rules for Mobile Homes
(814-23-900 through 814-23-909) and Installation as a Stove Heater.
This pellet stove, when installed, must be electrically grounded in accordance with local codes, or in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70.
Theauthorityhavingjurisdiction(suchasmunicipalbuildingdepartment,redepartment,repreventionbureau,
etc.)shouldbeconsultedbeforeinstallationtodeterminetheneedtoobtainapermit.
This appliance is designed specically for use only with pelletized wood. It is designed for residential installation according
to current national and local building codes as a freestanding room heater. It is also approved as a mobile home heater
which is designed for connection to an outside combustion air source.
The stove will not operate using natural draft or without a power source for the blower systems and fuel feed system and
must not be burned with any type of coal (see PROPERFUEL).
This stove is designed to provide the optimum proportions of fuel and air to the re in order to burn free of smoke and soot.
Any blockage of the air supply to or from the stove will seriously degrade its performance and will be evidenced by a smok-
ing exhaust and a sooting window. For best operation the ash content of the pellet fuel should be less than 1% and the
caloric value approximately 8200 BTU/LB. Avoid high ash content fuels because this will rapidly ll up the burn pot and
eventually cut off the combustion air supply.
Commercial and industrial installations of Breckwell Pellet Stoves should not be used since operational control is often not
well managed in these settings.
IMPORTANTINFORMATION
Model: __SP22-Maverick___________
Style: ____________________________
Serial Number:_____________________
Purchase Date: ____________________
Purchased From:___________________
___________________
___________________
MAILYOURWARRANTYCARDTODAY
To receive full warranty coverage, you will need
to show evidence of the date you purchased
your stove. We suggest that you attach your
sales invoice to this page, and ll in the form
on the left, so that you will have all the informa-
tion you need in one place should the need for
service or information occur.

" CUT HERE " CUT HERE
WARRANTY INFORMATION CARD
Name__________________________________________ Telephone #: (_____)_____________
City____________________________________________ State_______ Zip_________________
Email Address __________________________________________________________________
Model # of Unit________________________________ Serial #___________________________
Fuel Type: qWood qCoal qPellet qGas qOther _________________________
Place of Purchase (Retailer)______________________________________________________
City____________________________________________ State_______ Zip_________________
If internet purchase, please list website address___________________________________
Date of Purchase _______________________________________________________________
Reason for Purchase: qAlternative Heat qMain Heat Source
qDecoration qCost qOther _________________________
What was the determining factor for purchasing your new appliance?_______
I have read the owner’s manual that accompanies this unit and fully understand the:
Installation q Operation q and Maintenance q of my new appliance.
Print Name Signature Date
Please attach a copy of your purchase receipt.
Warranty not valid without a Proof of Purchase.
Warranty information must be received within 30 days of original purchase.
Detach this page from this manual, fold in half with this page to the inside and tape together. Apply a
stamp and mail to the address provided. You may use an envelope if you choose.
You may register online by going to www.usstove.com
All information submitted will be kept strictly condential. Information provided will not be sold for advertising purposes.
Contact information will be used solely for the purpose of product notications.

" CUT HERE " CUT HERE
Ê É
Fold Here
United States Stove Company
P.O. Box 151
South Pittsburg, TN 37380
Fold Here
PLACE
STAMP
HERE

3
SAFETY PRECAUTIONS
Do not operate your stove if you smell smoke com-
ing from it. Turn it off, monitor it, and call your
dealer.
Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter uid, or similar liquids
to start or “freshen up” a re in this stove. Keep all
such liquids well away from the stove while in use.
Never block free airow through the open vents of
the stove.
Keep foreign objects out of the hopper.
The stove will not operate during a power outage.
If an outage does occur, check the stove for smoke
spillage and open a window if any smoke spills into
the room.
Disconnect the power cord before performing any
maintenance or repairs on the stove.
NOTE: Turning the stove “off” does not disconnect
all power from the stove.
During the start up period; 1) DO NOT open the
viewing door; 2)DONOTopen the damper more
than ¼”; 3)DONOT add pellets to the burnpot by
hand; 4)DO NOT use the Fuel Feed button (un-
less you are priming the auger after running out of
pellets) as a dangerous condition could result.
Do not unplug the stove if you suspect a malfunc-
tion. Turn the stove off, periodically inspect it, and
call your dealer.
Contact your local building ofcials to obtain a per-
mit and information on any installation restrictions
or inspection requirements in your area. Notify
your insurance company of this stove as well.
This unit must be properly installed to prevent the
possibility of a house re. The instructions must be
strictly adhered to. Do not use makeshift methods
or compromise in the installation.
Your stove requires periodic maintenance and
cleaning. Failure to maintain your stove may lead
to smoke spillage in your home.
This stove must be connected to a standard 120
V., 60 Hz
grounded electrical outlet. Do not use an adapter
plug or sever the grounding plug. Do not route the
electrical cord underneath, in front of, or over the
stove.
The exhaust system should be checked, at a mini-
mum, at least twice a year for any build up of soot
or creosote.
Never try to repair or replace any part of the stove
unless instructions are given in this manual. All other
work should be done by a trained technician.
Do not throw this manual away. This manual has
important operating and maintenance instructions
that you will need at a later time. Always follow the
instructions in this manual.
Do not place clothing or other ammable items on or
near the stove.
The viewing door must be closed and latched during
operation.
Do not operate the stove if the ame becomes dark
and sooty or if the burnpot overlls with pellets. Turn
the stove off, periodically inspect it, and call your
dealer.
Hot while in operation. Keep children, clothing, and
furniture away. Contact may cause skin burns. Edu-
cate all children of the danger of a high temperature
stove. Young children should be supervised when
they are in the same room as the stove.
If the stove is installed in a room without air condi-
tioning, or in an area where direct sunlight can shine
on the unit, it is possible this can cause the tempera-
ture of the stove to rise to operational levels; one of
the sensors could then make the stove start on its
own. It is recommended that the stove be unplugged
when not in use for extended amounts of time (i.e.
during the summer months).
The exhaust system must be completely airtight
and properly installed. The pellet vent joints must
be sealed with RTV 500°F (260°C) silicone sealant,
and with UL-181-AP foil tape.
Allow the stove to cool before carrying out any main-
tenance or cleaning. Ashes must be disposed in a
metal container with a tight lid and placed on a no
combustible surface well away from the home struc-
ture.
This stove is designed and approved for pelletized
wood fuel only. Any other type of fuel burned in this
heater will void the warranty and safety listing.
When installed in a mobile home, the stove must be
bolted to the oor, have outside air, and NOT BE
INSTALLEDINABEDROOM(Per H.U.D. require-
ments). Check with local building ofcials.
Breckwell Hearth Products grants no warranty,
impliedorstated,fortheinstallationormainte-
nanceofyourstove,andassumesnoresponsi-
bilityofanyconsequentialdamage(s).
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө
Ө

4TABLE OF CONTENTS
INTRODUCTION ----------------------------------------------------------------------------------------------- 2
SAFETYPRECAUTIONS -------------------------------------------------------------------------------------- 3
SPECIFICATIONS ----------------------------------------------------------------------------------------------- 5
INSTALLATION ----------------------------------------------------------------------------------------------- 5
Preparation ----------------------------------------------------------------------------------------------- 5
Clearances ----------------------------------------------------------------------------------------------- 5
Combustion Air Supply ----------------------------------------------------------------------------- 6
When Outside Air Is Not Used -------------------------------------------------------------------- 6
Venting ----------------------------------------------------------------------------------------------- 6
Freestanding Installations ----------------------------------------------------------------------------- 7
Insert Installations -------------------------------------------------------------------------------------- 10
Electrical Installation ----------------------------------------------------------------------------- 13
Special Mobil Home Requirements ----------------------------------------------------------- 13
OPERATION--------------------------------------------------------------------------------------------------------14
Proper Fuel ----------------------------------------------------------------------------------------------- 14
Pre-Start-Up Check -------------------------------------------------------------------------------------- 14
Building a Fire -------------------------------------------------------------------------------------- 14
The HotRod™ Automatic Fire Starter ----------------------------------------------------------- 14
Panel Controls -------------------------------------------------------------------------------------- 14
Opening Door -------------------------------------------------------------------------------------- 15
Room Air Fan -------------------------------------------------------------------------------------- 15
Re-Starting a Warm Stove ----------------------------------------------------------------------------- 15
If Stove Runs Out Of Pellets -------------------------------------------------------------------- 16
Damper Control -------------------------------------------------------------------------------------- 16
Refueling ----------------------------------------------------------------------------------------------- 16
Breckwell Maintenance Tool -------------------------------------------------------------------- 16
Shutdown Procedure ----------------------------------------------------------------------------- 16
Safety Features -------------------------------------------------------------------------------------- 16
Optional Thermostat ----------------------------------------------------------------------------- 17
Thermostat Installation ----------------------------------------------------------------------------- 17
(PleaseReadThis) Operating Safety Precautions ----------------------------------------- 18
MAINTENANCE ----------------------------------------------------------------------------------------------- 19
Ash Removal----------------------------------------------------------------------------------------------- 19
Ash Disposal ----------------------------------------------------------------------------------------------- 19
Vacuum Use ----------------------------------------------------------------------------------------------- 19
Cleaning ----------------------------------------------------------------------------------------------- 19
Blowers ----------------------------------------------------------------------------------------------- 20
Chimney Cleaning -------------------------------------------------------------------------------------- 21
Recommended Maintenance Schedule ----------------------------------------------------------- 21
Removal & Replacement of Broken Door Glass-------------------------------------------------- 21
TROUBLESHOOTINGGUIDE ----------------------------------------------------------------------------- 22
Smoke Smell or Soot Build-Up -------------------------------------------------------------------- 27
ELECTRICALDIAGRAM --------------------------------------------------------------------------------------28
REPLACEMENTPARTSLIST ----------------------------------------------------------------------------- 29
LIFETIMELIMITEDWARRANTY------------------------------------------------------------------------------ 30

5INSTALLATION
SPECIFICATIONS
FREESTANDING:
Width: 21 ½”
Height: 28 ½” (with legs or pedestal)
Depth: 24”
Weight: 185 lbs.
Pedestal: 40 lbs.
Legs: 13 lbs.
Flue size: 3” or 4”
Hopper Capacity: Up to 45 lbs.
(this can vary widely depending on pellet size, length, and diameter)
EPA status: exempt
Burn time: 1 lb. to 4 ½ lbs. per hour
BTU range: 8,200 to 40,000
Approved installations: mobile home, alcove, conventional
FIREPLACEINSERT:
Width: 21 ½” (With ashing: 39”)
Height: 20” (With ashing: 30”)
Depth: 24” (In replace: 10 ¾”)
Weight: 185 lbs.
Flashing: 13 lbs.
Flue size: 3” or 4”
Hopper Capacity: Up to 45 lbs.
(this can vary widely depending on pellet size, length, and diameter)
EPA status: exempt
Burn time: 1 lb. to 4 ½ lbs. per hour
BTU range: 8,200 to 40,000
Approved installations: zero-clearance, masonry, as a built-in.
PREPARATION
Factory packaging must be removed, and some minor assembly work is required prior to
installation. Access to the rear of the stove is necessary.
The circuit board/control panel must be unpacked and installed in the side ashing on the
insert or side panel on the freestanding. (See installation instructions provided with the circuit
board)
NOTE: Normally, your dealer will perform these functions.
CLEARANCES
The Breckwell SP22 Freestanding has been tested and listed for installation in residential,
mobile home and alcove applications.
The SP22 Insert is approved for installation into code complying masonry replaces. It is also
approved for use in listed factory built replaces (UL 127) and standard residential built-ins
(see As A Built-In Fireplace), including Mobile Home built-in installations, of the following
description: all brands at least 34” wide and 20 ½” high.
FLOOR PROTECTION: Freestanding installations, minimum 21” wide by 28” deep. The stove
must be placed on a continuous (grouted joints) noncombustible material such as ceramic tile,
cement board, brick, 3/8” millboard or equivalent, or other approved or listed material suited
for oor protection.
THE MATERIAL(S) USED MUST HAVE, OR COMBINE TO HAVE, A MINIMUM INSULATIVE
RATING OF ‘R1’.
NOTE: ceramic tile, or any tile, requires a continuous sheet beneath to prevent the possibility
of embers falling through to the combustible oor if cracks or separation should occur in the
nished surface, this would include oor protection for Built-in raised hearths. Check local
codes for approved alternatives.
Clearances are measured from the sides, back and face (door opening) or stove body (refer
to g. 4).
DONOTUSEMAKESHIFTMATERIALSORCOMPROMISESINTHEINSTALLATIONOF
THISUNIT.
INSTALLVENTWITHCLEARANCESSPECIFIEDBYTHEVENTMANUFACTURER.
SIDEWALL CLEARANCES
ADJACENT WALL
ADJACENT WALL
WITH
VERTICAL
EXHAUST
BACKWALL
SIDEWALL
(SIDEWALL)
3”
1”
8 1/4”
*
(TOP)
1”
1”
3”
3”
9”
FIGURE 1
FIGURE 2
ALCOVE CLEARANCES
36” MAX.
48” MIN.
*WITH HORIZONTAL EXHAUST
38” MIN.
BACKWALL
WITH
VERTICAL
EXHAUST
(TOP) (TOP)
(SIDEWALL) (SIDEWALL)
*
3”
1”
9” 9”
8 1/4” 8 1/4”
STOVE DOOR FACE MUST BE
EQUAL TO OR PROTRUDE OUT
FROM FACE OF ALCOVE.
FIGURE 3
COMBUSTIBLE WALL
MANTLE
6”
12”
12”
12”
6”
0”
10”
NONCOMBUSTIBLE HEARTH
HEARTH EXTENSION
COMBUSTIBLE FLOOR
TOP
FACING
SIDE
FACING
FLOOR PROTECTION
FIGURE 4
21”
28”
6”

6INSTALLATION
COMBUSTIONAIRSUPPLY
For a mobile home installation the stove must be connected to an outside
source of combustion air. A 2” inside diameter metallic pipe, either exible or
rigid, may be attached to the inlet at the stove’s rear (refer to gures 5a, 5b,
and 6). A rodent guard (minimum ¼” wire mesh)/wind hood must be used at
the terminus (refer to gure 7). All connections must be secured and airtight by
either using the appropriately sized hose clamp and/or UL-181-AP foil tape.
Formobilehomeinstallationsonly: 2” inside diameter pipe may be used
for the rst 5 feet of combustion air supply run. From 5 to 10 feet use 2 ¾”
inside diameter pipe. No combustion air supply may exceed 10 feet.
SourcesofOutsideCombustionAir
a. In replaces
• Chimney top.
• Ash clean out door.
b. For freestanding installations
• A hole in oor near stove rear terminating only in a ventilated crawl
space.
• A hole in the wall behind the stove.
WHENOUTSIDEAIRISNOTUSED
If outside air is not used, it is important that combustion air is easily available
to the air inlet. A closeable outs ide air register can be used in tightly insu-
lated homes. In insert installations, ashing vents should not be restricted. The
ashing should not necessarily seal the replace face.
VENTING
The Breckwell SP22 Freestanding is certied for use with listed TYPE L-Vent,
3” or 4” diameter in size. The stove was tested with Simpson Duravent brand.
Class “A” chimney is not required. Refer to the instructions provided by the
vent manufacturer, especially when passing through a wall, ceiling or roof.
This is a pressurized exhaust system. All vent connector joints must be sealed
with 500OF (260OC) RTV silicone sealant to ensure consistent performance
and avoid smoke spillage. All horizontal connector joints must be sealed with
UL- 181-AP foil tape. We recommend that all vertical vent connector joints be
secured with a minimum of 3 screws.
It is strongly recommended that you have a minimum of 6’ of vertical pipe in
your exhaust system. For best performance of the stove limit the number of
elbows and horizontal pipe as much as possible.
DONOTCONNECTTHISUNITTOACHIMNEYFLUESERVINGANOTHER
APPLIANCE.
DONOTINSTALLAFLUEDAMPERINTHEEXHAUSTVENTINGSYSTEM
OFTHISUNIT.
INSTALLVENTATCLEARANCESSPECIFIEDBYTHEVENTMANUFACTURER.
21 1/2”
EXHAUST
PIPE
AIR
INLET
PIPE 28 1/2”
11” 6 1/2” 10 3/4”
FIGURE 5a
5 7/8”
FIGURE 5b
21 1/2”
28 1/2”
EXHAUST
PIPE
5 7/8”
11” 6 1/2” 10 3/4”
AIR
INLET
PIPE
FIGURE 6
AIR
INLET
PIPE
39”
21 1/2”
EXHAUST
PIPE
30”
6 1/2”
2 1/2” 2 1/4”
5 7/8”
FIGURE 7
24 3/4”
TRIM
COLLAR
28 1/2”
RODENT
GUARD
VENTILATED
CRAWL SPACE

7INSTALLATION
EquivalentVentLength(EVL)
The longer the run of pipe in your installation (both with inserts
and freestandings), the more restriction there is in the system.
Therefore, larger diameter pipe should be used.
• Use 4” pipe if you have more than 15 feet of equivalent
vent length.
• Horizontal runs shall not exceed 10 feet of EVL.
• It is recommended that vertical runs be a minimum of 8
feet.
• To calculate EVL, use the following conversions:
90º elbow or “T” = 5 equivalent feet
45º elbow = 3 equivalent feet
Horizontal Pipe Run = 1 equivalent foot per actual foot
Vertical Pipe Run = 0.5 equivalent foot per actual foot
NOTE: At altitudes above 3,000 feet, we suggest the use of
4” diameter vent at an EVL of 7 feet or more.
FREESTANDINGINSTALLATIONS
A.ASSEMBLINGPEDESTALORLEGSET
If using a pedestal, follow the instructions inside the Breckwell
SP22 Pedestal Set Part # A-22-P (refer to gure 8).
If using cast legs, follow the instructions inside the Breckwell
SP22 Leg Set Part # A-CGL-22 or # A-CL-22.
Legs are installed by using the four bolts provided in the kit
into the four holes under the stove at each corner, thread on
nuts from the top and tighten. Make sure to save the hole
plugs.
NOTE: If converting from legs to pedestal the hole plugs
must be installed in the unused holes.
B.HORIZONTALLYTHROUGHWALL (refer to Figure 9)
NOTE:Follow L-Vent chimney manufacturer’s instructions.
1. Position stove, adhering to clearances shown in Figures
1 & 2.
2. Locate position of hole in wall; directly behind stove
exhaust
vent (refer to gure 5).
3. Always maintain 3” clearance from combustible materials.
4. Install L-Vent wall thimble per L-Vent manufacturer’s
instructions.
5. Attach enough piping to penetrate and extend at least 6”
beyond exterior walls. An 8-foot vertical pipe run is sug-
gested where possible to reduce the possibility of smoke
spillage in the event of a loss of negative pressure.
6. Attach cap and seal outside wall thimbles with non-
hardening waterproof mastic.
7. T ermination should not be located so that hot exhaust
gases can ignite trees, shrubs, or grasses or be a hazard
to children. Exhaust gases can reach temperatures of
500ºF and cause serious burns if touched.
Locate terminations: a) not less than 3 feet above any forced
air inlet located within 10 feet; b) not less than 4 feet below
or horizontally from, or one foot above, any door, window or
gravity air inlet into any building; c) not less than two feet from
an adjacent building and not less than 7 feet above grade
when located adjacent to a public walkway. Mobile home in-
stallations must use a spark arrester.
FIGURE 8
FIGURE 9
VERTICAL ROOF VENT
WALL
THIMBLE
6” MINIMUM CLEARANCE
TO ANY COMBUSTIBLE
SURFACE
CLEAN-OUT TEE
A 90 DEGREE ELBOW
MAY ALSO BE USED
WALL STRAP
SEE VENT MANUFACTURER
FOR NUMBER AND SPACING
TO
APPLIANCE
L-VENT
ADAPTER
6” MINIMUM CLEARANCE

8INSTALLATION
C.VERTICALLYWITHNEWCHIMNEYSYSTEM(Referto
Figure10)
NOTE:Follow L-Vent chimney manufacturer’s instructions.
OPTION: To achieve a center vertical installation a 45º elbow
and a clean-out tee can be used to offset the pipe from the
exhaust outlet to the rear center of the stove.
OPTION: Install L-Vent elbow in place of clean-out tee. Locate
stove. Drop plumb bob to center of tee outlet, mark point on
ceiling . Install ceiling support and L-Vent pipe per L-Vent
manufacturer’s instructions.
1. Always maintain 3” clearance from combustible materials.
When passing through additional oors or ceilings, always
install restop spacer.
2. After lining up for hole in roof, cut either a round or square
hole in roof, always 3” larger all the way around pipe. Install
upper edge and sides of ashing under roong materials,
nail to the roof along upper edge. Do not nail lower edge.
Seal nail heads with non-hardening waterproof mastic.
3. Apply non-hardening, waterproof mastic where the storm
collar will meet the vent and ashing. Slide storm collar down
until it sits on the ashing. Seal and install cap. Mobile home
installations must use a spark arrester.
D.VERTICALLYINTOEXISTINGCHIMNEYSYSTEM
Adapters are available to adapt from 3” L-Vent to 6” or 8” Class-
A chimney. (Figure 11a)
As an alternative, 3” or 4” L-Vent can be run inside existing
chimney to termination. (Figure 11b)
This is the preferred method.
Follow guidelines for equivalent vent length.
FIGURE 10
FIGURE 11a
FIGURE 11b
12” MINIMUM CLEARANCE
TO ROOF
VERTICAL ROOF VENT
ATTIC
INSULATION
SHIELD
3” MINUMUM
CLEARANCES TO
COMBUSTIBLES
3” MINUMUM
CLEARANCES TO
COMBUSTIBLES
PELLET VENT TO
CHIMNEY ADAPTER
(SPV-CA)
UNIVERSAL
CONNECTOR
PELLET
VENT
NOTE:
THIS METHOD
IS PREFERRED
EXISTING
CHIMNEY
SYSTEM
EXISTING
CHIMNEY
SYSTEM
TO
APPLIANCE
CLEANOUT
TEE
45 DEGREE ELBOW
L -VENT ADAPTER

9INSTALLATION
E.VERTICALLYINTOEXISTINGMASONRYFIREPLACE
NOTE:Follow L-Vent chimney manufacturer’s instructions.
1. Have the masonry chimney inspected by a qualied
chimney
sweep or installer to determine its structural condition.
2. You will need a pipe length equal to the chimney height
from the hearth. If outside combustion air is to be used,
you will need a pipe length equal to the chimney height
plus 18 inches.
3. Install a blanking plate and the chimney pipe, and if used
the outside air pipe, as shown in Figure 12.
4. Attach the L-Vent adapter, a section of pipe and clean
out tee, making sure the clean out tee is centered in the
chimney ue area. Use RTV, metallic tape, and a
minImum of three self-taping screws at all joint connections
to ensure a tight seal.
5. Position the stove, adhering to the clearances in Figures
1 & 2.
6. Measure and build chimney top plate. Cut out holes for
chimney pipe, and if used the outside air pipe. Install and
seal with non-hardening mastic to prevent water leakage.
Install vent cap.
F.INSTALLATIONTHROUGHSIDEOFMASONRYCHIMNEY
NOTE: Follow L-Vent chimney manufacturer’s instructions.
1. Position the stove, adhering to the clearances in Figures
1 & 2. Mark the center of the hole where the pipe is to
pierce the masonry chimney.
2. It will be necessary to break out the masonry around the
location of the pipe center mark. Use a 4-inch diameter
hole for 3-inch pipe and 5-inch diameter hole for 4-inch
pipe.
3. Measure and build chimney top plate. Cut out holes for
chimney pipe, and if used the outside air pipe.
4. Install the tee on the bottom of the vertical pipe system and
lower it down the chimney until the center branch of the tee
is level with the center of the hole in the masonry, as shown
in Figure 13.
5. Install and seal the top plate from step 3 with non-hardening
mastic. Slip the storm collar over the pipe, and while holding
the pipe at the proper elevation, afx the collar with a mini-
mum of three ¼” stainless steel sheet metal screws. Seal all
joints and seams around the collar.
6. Connect the horizontal pipe by pushing it through the hole
in the masonry and lining it up with the branch in the tee.
Push the pipe into the tee while twisting it to lock it into the
tee.
7. If desired, once the horizontal pipe is in place, the space
between the pipe and masonry may be lled with high-
temperature grout.
8. Install the trim collar. An adjustable pipe length and adapter
may be needed to nish the connection to the stove.
HEARTH
TOP PLATE
(SEAL TO CHIMNEY TOP
WITH NON-HARDENING
MASTIC)
EXTENSION TO CHIMNEY TOP
REQUIRED.
3 OR 4 INCH STAINLESS STEEL
SINGLE WALL PIPE OR FLEX PIPE.
BLANKING PLATE (SEAL WITH
NON-HARDENING MASTIC).
3 OR 4 INCH STAINLESS STEEL
FLEX PIPE.
OPTIONAL OUTSIDE AIR
CLEAN-OUT-TEE (TYPE L)
OR 90 DEGREE ELBOW
TO
APPLIANCE
6” FROM STOVE
TO END OF HEARTH
NOTE:
FOLLOW METAL
CHIMNEY INSTALLATION
INSTRUCTIONS
6”
3”
FIGURE 12
FIGURE 13
TOP PLATE
(SEAL TO CHIMNEY TOP
WITH NON-HARDENING
MASTIC)
EXTENSION TO CHIMNEY TOP
REQUIRED.
L-VENT OR OPTIONAL
3 OR 4 INCH STAINLESS STEEL
SINGLE WALL PIPE OR FLEX PIPE.
PIPE ADAPTER
CLEAN-OUT TEE (TYPE L)
TRIM COLLAR
OPTIONAL OUTSIDE AIR
NOTE:
FOLLOW METAL
CHIMNEY INSTALLATION
INSTRUCTIONS
6”
3”

10 INSTALLATION
INSERTINSTALLATIONS
Insert installations must be vented with 3” or 4” pipe. Pipe
may be single wall stainless steel exible pipe. Vent may
terminate within chimney beyond a blanking plate or extend
to the chimney top. See“COMBUSTIONAIRSUPPLY” for
outside air access information.
The replace and chimney should be cleaned thoroughly
before starting the installation. We suggest painting the
interior of particularly old and dirty replaces to seal any
odors. In zero-clearance replace installations, when the
replace opening is above the oor or raised hearth, the
adjustable “Breckwell SP22 Z-C Legs” can be used to
bridge the gap between the hearth and stove bottom.
Refer to gure 14.
A. ASSEMBLINGTHEFLASHINGSET
Follow the instructions packaged with the SP22 Flashing
set part C-SP22-MED (refer to Figure 15).
BRECKWELL ZC
ADJUSTABLE LEGS
FIGURE 14
FIGURE 15
(OPTIONAL)
BRASS TRIM
(OPTIONAL)
BRASS TRIM
(OPTIONAL)
BRASS TRIM
TOP SURROUND PANEL
CIRCUIT
BOARD
LEFT SIDE
SURROUND
PANEL
RIGHT SIDE
SURROUND
PANEL
LEVELING
BOLT

11INSTALLATION
B. WHENVENTPIPEEXTENDSTOCHIMNEYTOP
(Refer to Figures 16 and 17)
1. You will need a pipe length equal to the chimney height
(from hearth) plus 6 inches. If outside combustion air is to
be used, you will need a pipe length (see“COMBUSTION
AIRSUPPLY”) equal to the chimney height plus 12 inches.
2. Attach cerablanket wrap (not included) to that end of vent
pipe that will connect to the stove. Use 12-inch lengths
of light gauge metal wire (not included) or metallic tape
(not included). This is to protect interior components from
excess heat.
3. Set the insert on the hearth and slide it in far enough to
attach the vent pipe (and combustion pipe if used).
4. Attach ashing (refer to Figure 15), route power cord out
the side nearest a 120V receptacle. Slide in insert.
5. Measure and build chimney top. Cut out hole for vent
pipe (and combustion air intake pipe, if used). Install and
seal with a non-hardening mastic to prevent water leak-
age. Install the vent cap.
C. WHEN VENTPIPE EXTENDSTHROUGH CHIMNEY
BLANKINGPLATE
MasonryFireplacesOnly)
(Refer to Figures 16 and 17)
1. You will need a pipe length that extends 12” above the
blanking plate.NOTE:This installation is optional but not
recommended. Outside combustion air cannot be drawn
from the chimney cavity in this installation.
2. Attach cerablanket wrap (not included) to that end of vent
pipe that will connect to the stove. Use 12-inch lengths of
light gauge metal wire (not included) or metallic tape. This
is to protect interior components from excessive heat.
3. Measure and build blanking plate. Cut out hole for vent
pipe (and combustion air intake pipe, if used). Install and
carefully seal blanking plate with non-hardening mastic.
Failure to properly seal may result in smoke spillage.
4. Slide vent pipe (and intake pipe if used) up through the
blanking plate hole, leaving enough to pull back down.
5. Set the insert on the hearth, adjust the leveling bolts on
the rear sides, slide it in far enough to attach the vent pipe
(and combustion air pipe if used). Be sure to seal where
the pipe passes through the blanking plate.
6. Attach ashing (refer to Figure 15), route power cord out
the side nearest a 120V receptacle. Slide in insert.
6”
6”
MAX
15”
12”
FIGURE 16
FIGURE 17
3”
TOP PLATE
(SEAL TO CHIMNEY TOP
WITH NON-HARDENING
MASTIC)
NOTE:
FOLLOW METAL
CHIMNEY INSTALLATION
INSTRUCTIONS
BLANKING PLATE (SEAL WITH
NON-HARDENING MASTIC).
OPTIONAL COMBUSTION AIR INTAKE
(EXTENDS THROUGH DHIMNEY TOP WITH
180 DEG. BEND) REQUIRED IN MOBILE
HOME AND ZERO-CLEARANCE FIREPLACES.
NOT RECOMMENDED IN MASONRY
FIREPLACES OR BUILT IN INSTALLATIONS.
LEVELING BOLTS
EXHAUST PIPE INSTALLATION
HEARTH
NOTE:
FOLLOW METAL
CHIMNEY INSTALLATION
INSTRUCTIONS
TOP PLATE
(SEAL TO CHIMNEY TOP
WITH NON-HARDENING
MASTIC)
EXTENSION TO CHIMNEY TOP OPTIONAL.
(REQUIRED IN MOBILE HOME AND ZERO-
CLEARANCE FIREPLACES.
RECOMMENDED IN ALL FIREPLACES).
3 OR 4 INCH STAINLESS STEEL
SINGLE WALL PIPE.
BLANKING PLATE (SEAL WITH
NON-HARDENING MASTIC).
CHIMNEY NEED ONLY EXTEND
12” ABOVE BLANKING PLATE.
3 OR 4 INCH STAINLESS STEEL
FLEX PIPE.
FIREPLACE INSERT
SIDE ELEVATION
1” CERIBLANKET
NOTE:
WHEN MANTLE EXTENDS
MORE THAN 6” FROM
FIREPLACE FACE, A 15”
MINIMUM DIMENSION
MUST BE MAINTAINED
FROM STOVE TOP TO
BOTTOM OF MANTLE.
OUTSIDE COMBUSTION AIR INSTALLATION
HEARTH

12 INSTALLATION
D. ASABUILT-INFIREPLACE
Figures 18 and 19 describe a SP22 installation vent-
ed into either a special chase built outside an outer
wall or a false inside wall. This is especially suited for
new construction or remodeling.
The equipment compartment (sides and rear of the
stove in replace) must be enclosed per the applica-
ble electrical standards. This can be accomplished
by the use of Breckwell’s panel kit part #A-PANEL-22.
NOTE: Floor protection for Built-in raised hearths
requires a continuous sheet beneath to prevent the
possibility of embers falling through to the combus-
tible oor if cracks or separation should occur in the
nished surface.
Thechasedimensionsshownareminimumsand
mustbemaintained.
FIGURE 18
22”
8”
MIN
MANTLE
FACADE
OPENING
24”
34”
34” MIN
17” MIN
RAISED HEARTH
SEE “INSERT INSTALLATIONS” FOR
PANEL SURROUND INSTALLATION 6”
MIN.
6”
MIN.
3”
MIN.
3”
MIN.
LISTED
CHIMNEY
CAP
STORM
COLLAR
CHASE CAP
MANTLE
OVER 6”
FACING
6”
MAX
15”
THE PANEL SURROUND KIT
(PN C-P22-MED)
ATTACH THE PANEL SURROUND
TO THE PANEL SURROUND TO
THE FACE OF THE FIREPLACE
WITH ONE SCREW. 12”
MIN.
22”
MIN.
6”
MIN.
8”
MIN.
FLOOR PROTECTOR MUST BE
CONTINUOUS WITH NO JOINTS RAISED HEARTH MUST BE BUILT
OF 8” HOLLOW CONCRETE BLOCKS.
IF CHOOSING TO VENT HORIZONTALLY THROUGH THE WALL, WE RECOMMEND
TERMINATING VERTICALLY WITH AN ADDITIONAL RUN OF AT LEAST 5 FEET.
*
OUTSIDE AIR MAY BE DRAWN FROM
A VENTILATED CRAWL SPACE.
OUTSIDE AIR
LISTED
CHIMNEY
CAP
*
LISTED
THIMBLE
6”
24”
MIN.
EQUIPMENT
COMPARTMENT
(OPTIONAL VERTICAL INSTALLATION)
L-VENT ONLY
SIDING
5/8” SHEETROCK
(ENTIRE FACADE)
A 1/4” (OR SMALLER) WIRE MESH
SCREEN MUST BE INSTALLED IN
THIS INSTALLATION TO COVER
THE EQUIPMENT COMPARTMENT.
19
18
FIGURE 19

13INSTALLATION
E.   INSTALLATION IN TO A FACTORY BUILT
(METAL)FIREPLACE
(Refer to gure 20)
When installing into a factory built replace, the rebox
must accept the insert without modication other than
removing bolted or screwed together pieces such as
smoke shelf/deectors, ash lips, screen or door tracks
and damper assemblies. These items must be reinstalled
to restore the replace to its original operating condition
if the insert is removed and not replaced. The removal of
any part must not alter the integrity of the listed replace
in any way. In zero-clearance replace installations, when
the replace opening is above the oor or raised hearth,
the adjustable “Breckwell SP22 Z-C Legs” can be used
to bridge the gap between the hearth and stove bottom.
Refer to gure 14.
The factory built replace must be listed per UL 127.
Installation must include a full height listed chimney
liner meeting type HT requirements (2100o F) per 1777
(U.S.). The liner must be securely attached to the insert
ue col lar and the chimney top. The damper area must
be sealed to prevent room air passage to chimney cavity.
Alteration of the replace in any manner is not permitted
except with the following exceptions:
• External trim pieces, which do not affect the operation
of the replace, may be removed proving they can be
stored on or within, the replace for re-assembly if the
insert is removed.
• The replace damper may be removed to install the
chimney liner.
Circulating air chambers, louvers or cooling air inlet or
outlet ports (i.e. in a steel replace liner or metal heat
circulator) shall not be blocked.
Means must be provided for removal of the insert to clean
the chimney ue.
A permanent metal warning label must be attached to the
back wall of the replace opening stating the following:
• “This replace has been altered to accommodate a
replace insert and should be inspected by a qualied
person prior to re-use as a conventional replace.”
• This label is available upon request.
Finalapprovaliscontingentontheauthorityhaving
jurisdiction.
ELECTRICALINSTALLATION
This stove is provided with a 6-foot grounded electrical
cord extending from the rear of the stove. We recom-
mend connecting to a good quality surge protector
that is plugged into a standard three-prong, 120V,
60hz electrical outlet. Voltage variations can lead to
serious performance problems. The Breckwell electri-
cal system is designed for 120V AC with no more than
5% variation. Breckwell cannot accept responsibility for
poor performance or damage due to inadequate voltage.
If connected to an older, two-prong outlet, a separate
ground wire should be run to a proper ground (refer this
to a qualied technician). Always route the electrical cord
so that it will not come in contact with any hot part of the
stove.
FIGURE 21
SECURE PEDESTAL TO FLOOR
WITH 2, 1/4” x 2” LONG
LAG BOLTS.
B
A
DRILL 2, 5/16” HOLES
IN PEDESTAL BASE.
VERTICAL CAP
STORM COLLAR
COVER PLATE
(NON-COMBUSTIBLE)
SEAL WITH SILICONE.
3 OR 4 INCH L-VENT
OR STAINLESS STEEL
FLEXIBLE OR SINGLE
WALL PIPE
THE SMOKE SHELF
MAY BE REMOVED
12” THE DAMPER MAY
BE REMOVED
INTERNAL BAFFLES
MAY BE REMOVED
TO PREVENT FIREPLACE
ODORS FROM ENTERING
THE HOME, PAINT THE
INTERIOR OF THE FIREPLACE
WITH LATEX PAINT
THE METAL SIDES, FRAME MEMBERS, OR OTHER
STRUCTURAL COMPONENTS OF THE FACTORY BUILT
FIREPLACE MAY NOT BE REMOVED OR ALTERED
USE THE ZERO-CLEARANCE
SKIRT TO SUPPORT THE
INSERT ON RAISED FIREPLACES
THE MASONRY LINING
MAY NOT BE REMOVED
NOTE:
THE LOG SHELF, SCREEN,
AND DOORS (IF PRESENT)
MUST BE REMOVED
FIGURE 20
SPECIALMOBILEHOMEREQUIREMENTS
WARNING:DONOTINSTALLINASLEEPINGROOM.
NOTE: Installation should be in accordance with the Manufactured Home and
SafetyStandard(HUD),CFR3280,Part24
For installation in a mobile home, an outside source of combustion air must be used
(see “COMBUSTIONAIRSUPPLY”).
The SP22 must be grounded to the steel chassis of the home with 8 Ga. copper wire
using a serrated or star washer to penetrate paint or protective coating to ensure
grounding.
The SP22 must be securely fastened to the oor of the mobile home through the two
holes in the rear of the stove using 2, ¼” lag bolts that are long enough to go through
both a hearth pad, if used, and the oor of the home. (See gure 21)
Refer to “VENTING” for proper exhaust congurations.
CAUTION:THESTRUCTURALINTEGRITYOFTHEMOBILEHOMEFLOOR,WALL
ANDCEILING/ROOFMUSTBEMAINTAINED.

14 OPERATION
PANELCONTROLS(See Figure 22)
The blowers and automatic fuel supply are controlled from a panel on the left-hand side of the
SP22. The control panel functions are as follows.
a.ON/OFFSWITCH
• When pushed the stove will automatically ignite. No other restarter is necessary. The
igniter will stay on for at least 10 and up to 15 minutes, depending on when Proof of Fire
is reached. The re should start in about 5 minutes.
• The green light located above the On/Off button (in the On/Off box) will ash during the
ignition start-up period. (See gure 22)
• The Feed Rate Advance is inoperable during the ignition start period. When the red light
continuously stays on the Feed Rate Advance can be adjusted to achieve the desired
heat output.
NOTE:If the stove has been shut off, and you want to re-start it while it is still warm, the “on/
off” button must be held down for 2 seconds.
b.FUELFEEDSWITCH
• When the “Fuel Feed” button is pushed and held down the stove will feed pellets
continuously into the burnpot.
• While the stove’s auger system is feeding pellets the amber light (in the “Fuel Feed” box)
will be on. (See gure 22)
CAUTION: DO NOT USE THIS CONTROL DURING NORMAL OPERATION BECAUSE IT
COULD SMOTHER THE FIRE AND LEAD TO A DANGEROUS SITUATION.
c.HIGHFANSWITCH
• The room air fan speed varies directly with the feed rate. The “HIGH FAN” switch overrides
this variable speed function. It will set the room air blower speed to high at any feed rate
setting.
• When the “HIGH FAN” button is pushed the room air fan will switch to its highest setting.
• When this button is pushed again the room air fan will return to its original setting based
on the Feed Rate Advance setting.
d.RESETTRIM
Different size and quality pellet fuel may require adjustment of the “1” feed setting on the Feed
Rate Advance bar graph. Thisisusuallyaone-timeadjustmentbasedonthefuelyouare
using.The “RESET TRIM” button when adjusted will allow for 3 different feed rate settings for
the #1feedsettingonly.To adjust simply push the “RESET TRIM” button while the stove is
operating at setting “1” and watch the bar graph.
• When the “1” and “3” lights are illuminated on the bar graph the low feed rate is at its
“lowest” setting. (approx. 0.9 pounds per hour)
• When the “1” light is illuminated on the bar graph the low feed rate is at its “normal”
setting.
• When the “1” & “4” lights are illuminated on the bar graph the low feed rate is at its
“highest” setting.
NOTE:When the stove is set on “1” the “reset trim” values will be shown on the Feed Rate
Advance bar graph. For example if the Reset Trim is set to its lowest setting every time the
stove is set to low the “1” and “3” lights will be illuminated on the bar graph.
e.HEATLEVELADVANCE
• This button when pushed will set the pellet feed rate, hence the heat output of your stove.
The levels of heat output will incrementally change on the bar graph starting from level “1”
to “4”.
NOTE: When dropping more than 2 heat level settings (i.e. 4 to 1) push the ‘High Fan’ but-
ton and allow the room air fan to run at that setting for at least 5 minutes to prevent the stove
from tripping the high temp thermodisc. If the high temp thermodisc does trip see “SAFETY
FEATURES”.
CAUTION:THE “4” SETTING IS DESIGNED FOR TEMPORARY USE ONLY. IF USED FOR
EXTENDED PERIODS, IT CAN SHORTEN THE LIFE EXPECTANCY OF THE UNITS COM-
PONENTS. AVOID USE AT THIS SETTING FOR MORE THAN ONE HOUR AT A TIME.
FIGURE 22
Fuel Feed
High Fan
Reset Trim

15
OPERATION
PROPERFUEL
THISSTOVEISAPPROVEDFORBURNINGPELLETIZEDWOODFUELONLY!Factory-approved pellets are those ¼” or 5/16” in diameter and not
over 1” long. Longer or thicker pellets sometimes bridge the auger ights, which prevents proper pellet feed. Burning wood in forms other than pellets is
not permitted. It will violate the building codes for which the stove has been approved and will void all warranties. The design incorporates automatic feed
of the pellet fuel into the re at a carefully prescribed rate. Any additional fuel introduced by hand will not increase heat output but may seriously impair the
stoves performance by generating considerable smoke. Do not burn wet pellets. The stove’s performance depends heavily on the quality of your pellet fuel.
Avoid pellet brands that display these characteristics:
a. ExcessFines – “Fines” is a term describing crushed pellets or loose material that looks like sawdust or sand. Pellets can be screened before being
placed in hopper to remove most nes.
b. Binders – Some pellets are produced with materials to hold them together, or “bind” them.
c. Highashcontent – Poor quality pellets will often create smoke and dirty glass. They will create a need for more frequent maintenance. You will have
to empty the burnpot plus vacuum the entire system more often. Poor quality pellets could damage the auger. Breckwell cannot accept responsibility
for damage due to poor quality pellets. Your dealer can recommend a good quality pellet dealer in your area.
PRE-START-UPCHECK
Remove burnpot, making sure it is clean and none of the air holes are plugged. Clean the rebox, and then reinstall burnpot. Clean door glass if neces-
sary (a dry cloth or paper towel is usually sufcient). Never use abrasive cleaners on the glass or door. Check fuel in the hopper, and rell if necessary.
NOTE:The SP22 Hopper can hold up to 45 lbs. of pellets.
BUILDINGAFIRE
Never use a grate or other means of supporting the fuel. Use only the Breckwell approved burnpot.
During the start up period:
1)DONOT open the viewing door.
2)DONOT open the damper more than ¼”.
3)DONOT add pellets to the burnpot by hand.
4)DONOT use the Fuel Feed button (unless you are priming the auger after running out of pellets).
A dangerous condition could result.
NOTE:During the rst few res, your stove will emit an odor as the high temperature paint cures or becomes seasoned to the metal. Maintaining smaller
res will minimize this. Avoid placing items on stovetop during this period because paint could be affected.
THEHOTRODAUTOMATICFIRESTARTER
a. Fill hopper and clean burnpot.
b. Press “Power” button. Make sure light is on.
c. The damper should be completely closed or open no more than ¼” during start-up. This will vary depending on your installation and elevation. Once
re is established adjust for desired ame increasing the amount the damper is open as the heat setting is increased. (See“DAMPERCONTROL”)
d. Adjust feed rate to desired setting by pressing “Feed Rate Advance” button.
If re doesn’t start in 15 minutes, press “Power”, wait a few minutes and start procedure again.
DAMPERCONTROL
The damper control rod on the stove’s lower left side adjusts the combustion air. This control is necessary due to the varied burn characteristics of individual
installations, different pellet brands and pellet feed rates. It allows you to improve the efciency of your stove. Providing correct combustion air will reduce
the frequency of cleaning your glass door and prevent the rapid buildup of creosote inside your stove and chimney.
You should adjust the damper based on the re’s appearance. A low, reddish, dirty re can be improved by pulling the damper out slightly. A “blow torch”
re can be improved by pushing the damper in a bit.
As a general rule, on lower feed rate settings, the damper should be in farther. On higher feed rates, the damper should be more open. Through trial and
error, you will nd the best setting. Consult your dealer if you need help.
NOTE:On “1”, damper should be either completely closed or out approximately ⅛” to ¼”. If damper is out too far, it can cause the re to go out.
OPENINGDOOR
If the door is opened while the stove is in operation it must be closed within 30 seconds or the stove will shut down. If the stove shuts down push the “Power”
button to continue the operation of your stove.
ROOMAIRFAN
When starting your stove the Room Air Fan will not come on until the stove’s heat exchanger warms up. This usually takes about 10 minutes from
startup.

16 OPERATION
RE-STARTINGAWARMSTOVE
If the stove has been shut off, and you want to re-start it while it is still warm, the “on/off” button must be held down for 2 seconds.
IFSTOVERUNSOUTOFPELLETS
The re goes out and the auger motor and blowers will run until the stove cools. This will take 30 to 45 minutes.
After the stove components stop running the “Power” and the BAR GRAPH lights stay on for 10 minutes.
After the 10 minutes the “3” light on the bar graph will ash and the “Power” light will go off.
To restart, rell hopper, press “Power” button, and then press “Fuel Feed” button until pellets begin to fall into burnpot.
REFUELING
We recommend that you not let the hopper drop below ¼ full.
KEEPHOPPERLIDCLOSEDATALLTIMESEXCEPTWHENREFILLING.DONOTOVERFILLHOPPER.
A tool has been provided to help with the following functions:
a. Stirringpelletsinhopper – unlike liquids in a tank, pellets do not drain evenly into the auger. Bridging across the opening can
occur. Pellets can hang up on the sides of the hopper. Occasionally “stirring” the hopper can help.
NOTE: To help prevent bridging of pellets, common wax paper can be rubbed on the sidewalls and bottom of the hopper.
b. Cleaningheatexchangertubes – see instructions in“CLEANING”.
c. Scrapeashesfromburnpot.
SHUTDOWNPROCEDURE
Turning your Breckwell stove off is a matter of pressing the “Power” control panel switch. The red light will go out. The blowers will continue
to operate until internal rebox temperatures have fallen to a preset level.
SAFETYFEATURES
a. Your stove is equipped with a high temperature thermodisc. This safety switch has two functions.
1. To recognize an overheat situation in the stove and shut down the fuel feed or auger system.
2. In case of a malfunctioning convection blower, the high-temperature thermodisc will automatically shut down the auger, prevent-
ing the stove from overheating.
NOTE: On some units, once tripped, like a circuit breaker, the reset button will have to be pushed before restarting your stove. On other
units the thermodisc has no reset button and will reset itself once the stove has cooled. The manufacturer recommends that you call your
dealer if this occurs as this may indicate a more serious problem. A service call may be required.
b. If the combustion blower fails, an air pressure switch will automatically shut down the auger.
NOTE:Opening the stove door for more than 30 seconds during operation will cause enough pressure change to activate the air switch,
shutting the fuel feed off. Close the door and press “On/Off” button to continue operation of your stove.
FIGURE 23

17THERMOSTAT INSTALLATION
OPTIONALTHERMOSTAT
A thermostat may help you maintain a constant house temperature auto-
matically. A millivolt thermostat is required. A xed wall mount or Breckwell’s
hand held model can be used. The control panel can be set up two ways to
operate your stove in thermostat mode.
THERMOSTATINSTALLATION
• AMILLIVOLTTHERMOSTATISREQUIRED.
• Unplug stove from power outlet.
• Remove control board from stove.
• The two thermostat wires connect to the terminal block on the lower left
side of the back of the control board.
(See gure 24)
• Insert the wires in the terminal side and tighten the two screws.
MODES
TO SWITCH BETWEEN ANY OF THE THREE MODES THE STOVE MUST
BE SHUT OFF, THE NEW MODE SELECTED, AND THE STOVE RE-
STARTED.
MANUAL MODE
• USETHISMODEEXCLUSIVELYIFYOUDONOTCONNECTAN
OPTIONALTHERMOSTAT
• In this mode the stove will operate only from the control panel as detailed
in the “OPERATION” section of this owner’s manual.
HIGH/LOW THERMOSTAT MODE
• USETHISMODEONLYIFYOUCONNECTATHERMOSTAT
• When engaged in this mode the stove will automatically switch between
two settings. When warm enough, it will switch to the #1 or low setting. The
room air blower will also slow to its lowest speed.
• The Heat Level Advance setting on the bar graph will stay where it was
initially set. When the house cools below the thermostat setting, the stove
will switch to the feed rate of the heat level advance setting.
ON/OFF THERMOSTAT MODE
• USETHISMODEONLYIFYOUCONNECTATHERMOSTAT
• In this mode when the home is warm enough the stove will shut off. The
fans will continue to run until the stove cools.
• When the home cools below the thermostat setting, the stove will auto-
matically restart and run at the last feed rate setting.
NOTE: When in “high/low” or “on/off” thermostat mode –
• Do not operate the stove higher than the #3 setting.
• Set damper control rod approximately ¼” to ½” out. This will vary de-
pending on elevation and weather conditions. Observe stoves operation and
adjust damper as necessary.
FIGURE 24

18 OPERATION
OPERATINGSAFETYPRECAUTIONS
PLEASEREADTHIS!
a. Hotwhileinoperation.Keep children, clothing, and furniture away. Contact may cause skin burns.
b. Ifyounoticeasmolderingre (burnpot full but no visible ame) ANDaheavysmokebuildupinrebox,immediatelyTURN
OFFthestove,butDONOTunplugit.Donotopenthedoor,changethedampersettingortamperwithanycontrolsonthe
stove. Wait until rebox clears, and blowers shut down, do as instructed in “PRE-START-UPCHECK” and“BUILDINGAFIRE”,
then attempt to restart the re. If the problem persists contact your dealer.
c. WARNING:DONOTADDPELLETSTOTHEBURNPOTBYHANDATANYTIME,ADANGEROUSCONDITIONCOULDRE-
SULT.
d. WARNING:DURINGTHESTARTUPCYCLE;1)DONOTOPENTHEVIEWINGDOOR;2)DONOTOPENTHEDAMPERMORE
THAN¼”;3)DONOTUSETHEFUELFEEDBUTTON (UNLESS PRIMING THE AUGER AFTER RUNNING OUT OF PELLETS).
ADANGEROUSCONDITIONCOULDRESULT.
e. Pelletsshouldbestoredinadryplace.Thepelletsshouldnotbestoredwithin12”ofthestove.
f. DO NOT STORE OR USE FLAMMABLE LIQUIDS, ESPECIALLY GASOLINE, IN THE VICINITY OF YOUR BRECKWELL
STOVE.NEVERUSEAGASORPROPANETORCH,GASOLINE,GASOLINE-TYPELANTERNFUEL,KEROSENE,CHAR-
COALLIGHTERFLUIDORSIMILARFLUIDSTOSTARTOR“FRESHENUP”AFIREINTHISHEATER.
g. WARNING:DONOTOVERFIRETHISSTOVE. This may cause serious damage to your stove and void your warranty. It also may
create a re hazard in your home. IFANYEXTERNALPARTOFTHEUNITBEGINSTOGLOW,YOUAREOVERFIRING.Im-
mediatelypressthe“POWER”switchonthecontrolpanel.
h. KEEPALLLOOSEORMOVEABLEHOUSEHOLDCOMBUSTIBLES,SUCHASFURNITURE,DRAPES,TOYS,ETC.ATLEAST
THREEFEETFROMTHEOPERATINGSTOVE.
i. Maintain proper ventilation. It is important that adequate oxygen be supplied to the re for the combustion process. Modern houses
are often so well insulated that it may become necessary to open a window slightly or install an outside air vent to provide sufcient
combustion air.
j. Since heating with a solid fuel is potentially hazardous, even with a well made and thoroughly tested stove, it would be wise to install
strategically placed smoke detectors and have a re extinguisher in a convenient location, near an exit.
k. Do not open stove door when operating unless necessary. This will create a dirty, inefcient burn and could allow smoke spillage or
sparks to escape.
l. Do not permit operation by young children or those unfamiliar with stove’s operation.
m. Donotserviceorcleanthisappliancewithoutdisconnectingthepowercord.
n. Do not abuse the door glass by striking, slamming or similar trauma. Do not operate the stove with the glass removed, cracked or
broken.
o. If the stove is installed in a room without air conditioning, or in an area where direct sunlight can shine on the unit, it is possible this
can cause the temperature of the stove to rise to operational levels; one of the sensors could then make the stove start on its own.
It is recommended that the stove be unplugged when not in use for extended amounts of time (i.e. during the summer months).