Bresser 7002530 User manual

Weather Station
Professional Rain Gauge
Quickstart guide

2 / 12
1 Imprint
Bresser GmbH
Gutenbergstr. 2
46414 Rhede
Germany
http://www.bresser.de
If you wish to submit a warranty claim or service request, please refer to the “Warranty” and “Service”
information in this document. Please be aware that any requests or submissions sent directly to the
manufacturer cannot be processed.
Errors excepted. Subject to technical modifications.
© 2020 Bresser GmbH
All rights reserved.
Reproduction of this document, including extracts, in any form (photocopied, printed etc.) or the use
and distribution of this document by electronic means (image file, website etc.) is not permitted without
the prior written consent of the manufacturer.
The terms and brand names of the respective companies used in this document are protected by
brand, patent or product law in Germany, the European Union and/or other countries.
2 Validity information
This documentation is valid for the products with the article numbers listed below:
7002530
Manual version: v0620
Manual description:
Quickstart_7002530_Professional-Rain-Gauge_en_BRESSER_v062020a
With any service inquiries, please state these information.
3 About this Instruction Manual
NOTICE
This Quick Start guide is not intended to replace the more detailed user manual.
Please read the safety instructions and the operating instructions carefully before use.
4 General safety instructions
DANGER
Risk of suffocation
Improper use of this product can result in suffocation. This is particularly dangerous for children. The
following safety information must be observed at all times.
Keep packaging materials (plastic bags, rubber bands etc.) away from children. They can cause
suffocation.
This product contains small parts that could be swallowed by children. There is a risk of choking!

3 / 12
DANGER
Risk of electric shock
This device has electronic parts operated via a power source (power supply and/or batteries). Im-
proper use of this product can cause an electric shock. An electric shock can cause serious or poten-
tially fatal injuries. The following safety information must be observed at all times.
Children must only use the device under adult supervision! Only use the device as described in the
manual; otherwise, you run the risk of an electric shock.
DANGER
Risk of explosion
Improper use of this product can cause an explosion. The following safety information must be ob-
served at all times to prevent an explosion.
Do not expose the device to high temperatures. Use only the recommended batteries. Do not
short-circuit the device or batteries, or throw them into a fire! Excessive heat or improper handling
could trigger a short-circuit, a fire or an explosion!
NOTICE
Risk of damage to property
Improper handling can result in damage to the device and/or to the accessories. Always observe the
following safety information when using the device.
Never disassemble the device. In the event of a fault, please contact your specialist retailer. The
specialist retailer will contact the service centre and send the device for repair if necessary.
Do not immerse the unit in water!
Do not expose the device to impacts, vibrations, dust, constant high temperatures or excessive hu-
midity. This can result in malfunctions, short-circuits or damage to the batteries and components.
Use only the recommended batteries. Always replace weak or empty batteries with a new, com-
plete set of batteries at full capacity. Do not use batteries from different brands or with different ca-
pacities. Remove the batteries from the unit if it has not been used for a long time.
NOTICE
Risk of voltage damage!
The manufacturer is not liable for damage related to improperly installed batteries!

4 / 12
5 Parts overview Base station
1 LCD display with backlight 2 Alert LED indicator
3 HISTORY button 4 SINCE button (Total Rainfall)
5 RAIN button (Rainfall) 6 MEM button (MAX/MIN)
7 CLOCK button 8 ALARM button
9 ALERT button 10 Wall mount
11 DOWN button 12 UP button
13 Battery compartment 14 °C/°F slide switch
15 MM/IN slide switch (mm / inch) 16 RCC button
17 SCAN button 18 RESET button
19 SNOOZE/LIGHT button 20 Table stand
A
20
1
2
3456
19
7
10
8911 12
13
14 15 16 17
18

!"!#$
% &'()*!+,-(,.-/!0'.1!2'32-!'14!56+7-!+8
4-9.,-(:
!
"
#
$
%
&'()#*
+
# 0'4.').+1!*;.-94 $ 0-4!<=>!.14.6')+(
? @+31).12!A'*- B @+31).12!69'C
0'.1!6+99-6)+( % >('.1!;+9-*
D E.77.12!A36F-) G 0'.1!*-1*+(
H 0=5=E!A3))+1 #I J'))-(:!6+C7'()C-1)

%!"!#$
!"#$%"&%'$()*$+,
J'*-!*)').+1!KLMN!O.(-9-**!0'.1!2'32-!*-1*+(!KJMN!@+31).12!'66-**+(.-*!KPM
L9*+!(-Q3.(-4!K1+)!.16934-4MR
5)').+1R!$!76*[email protected](+!A'))-(.-*!K#S TN!):7-!LLM
5-1*+(!B!76*[email protected](+!A'))-(.-*!K#S TN!):7-!LLM
56(-/4(.,-(

7 / 12
7 Screen display
1 SINCE icon (Total rainfall) 2 HISTORY icon (History data)
3 Time 4 Daylight saving time (DST) on
5 Ice pre-alert on 6 Weekday
7 Alarm Mode 8 Alarm on
9 Day and Month 10 Rainfall indicator
11 Past time 12 Histogram
13 Time range record indicator 14 Current Rainfall reading
236
45
1
897
10 13 14
11
12
15
16
18 19 20 21
23
22
24 25 27 28
26
29 30
17

8 / 12
15 HI Alert 16 HI Alert on
17 Rainfall unit (in/h, mm/h) 18 Outdoor indicator
19 MAX/MIN indicator 20 Outdoor temperature
21 Battery level indicator (sensor) 22 Outdoor sensor signal strength indicator
23 HI/LO Alert
and Alarm on
24 Indoor indicator
25 Indoor humidity 26 MAX/MIN indicator
27 Indoor temperature 28 Battery level indicator (base station)
29 HI/LO Alert for humidity and Alarm on 30 HI/LO Alert for temperature and Alarm on
8 Setting up power supply
Basestation
1. Remove the battery compartment cover.
2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.
3. Replace the battery compartment cover.
4. Wait until the indoor temperature is displayed on the base station.
Remote sensor
5. Loosen the screws at the battery compartment cover with a small Philips screwdriver and remove
the cover.
6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.
7. Put the sealing frame back onto the edge of the battery compartment.
8. Replace the cover and retighten it with the screw.
Battery replacement
9. Press the RESET button on the sensor after every battery change.
10. Press the SCAN button on the base station to re-establish pairing.

9 / 12
9 Attaching rubber pads
Attach the supplied self-adhesive rubber pads to the clamps as shown to ensure a firmer fitting of the
mounting rod.
10 Remote sensor installation and mounting
Depending on the desired location, the remote sensor can be put on the table or mounted on the wall.
NOTICE! During the installation make sure that the device is minimum 1.5 meters off theground.The location should be as free as possible from obstacles to ensure an accurate measurement. The
remote sensor should be installed / mounted horizontally and within 150 m of the base unit.

!"#" $
!"#$%%$#&'!('!($()*+#&,$%(#-.*(/0$1&0$%(#-.*(2&$0*#*+3(45(006
% &'()*"+,*"-()."/0"+,*"1/23+435"-(6*"/0"+,*"7*1/+*"6*36/7"/3"+,*"+2-*"(38"97*66"+,*"1/23+435
)'(19"(5(436+"+,*"+2-*"07/1"+,*"/+,*7"648*%
$% :'48*";"6)7*<6"+,7/25,"+,*"-/7*",/'*6"/0"+,*"1/23+435")'(19"(38"+,7/25,"+,*"-/7*",/'*6"/0"+,*
1/23+435"-(6*"/3"+,*"/+,*7"64+*%
=% &2+"/3"+,*";"32+6"(38"+45,+*3"+,*"6)7*<")/33*)+4/3"->",(38%
?2+/1(+4)"+41*"6*++435
?0+*7"+,*"9/<*7"6299'>"<(6"*6+(-'46,*8@"+,*")'/)."<4''"(2+/1(+4)(''>"6*(7),"0/7"+,*"7(84/"6453('%"A,*
)'/)."<4''"(2+/1(+4)(''>"6*(7),"0/7"+,*"7(84/"6453('%
B0"+,*"7(84/"6453('"46"7*)*4C*8")/77*)+'>@"+,*"8(+*"(38"+41*"<4''"-*"6*+"(2+/1(+4)(''>"(38"+,*"7(84/")/3+7/'
6453('"4)/3"+2736"/3%
B0"+,*")'/)."0(4'6"+/"7*)*4C*"+,*"+41*"6453('@"5/"(,*(8"<4+,"+,*"0/''/<435"6+*96D
% &7*66"EFF"-2++/3"/3"+,*"-(6*"6+(+4/3"23+4'"7(84/"6453('"6>1-/'"0'(6,*6%
$% B0"+,*"8*C4)*"46"6+4''"3/+"7*)*4C435"+,*"6453('@"+,*"+41*"126+"-*"6*+"1(32(''>%
E*(8"+,*"8*+(4'*8"1(32('"0/7"1/7*"430/71(+4/3"(-/2+"1(32('"+41*"(38"('(71"6*++435"G6**"8/<3'/(8"43H
0/71(+4/3"/3"9(5*"$I%
$ E*)*4C435"1*(627*1*3+6"(2+/1(+4)(''>
J3)*"-(++*74*6"(7*"436+(''*8@"+,*"-(6*"6+(+4/3"<4''"8469'(>"+,*"1*(627*1*3+"7*(84356%"E*(84356"07/1
+,*"7*1/+*"6*36/7"<4''"-*"8469'(>*8"<4+,43"="1432+*6"(0+*7"9/<*7435"4+"/3%
E*(8"+,*"8*+(4'*8"1(32('"0/7"1/7*"430/71(+4/3"(-/2+"7*(84356"G6**"8/<3'/(8"430/71(+4/3"/3"9(5*"$I%
= E(430(''
A,*"-(6*"6+(+4/3"8469'(>6",/<"1(3>"14''41*+*76"#"43),*6"/0"7(430(''"(7*"())212'(+*8"/C*7"("+41*
9*74/8@"-(6*8"/3"+,*")277*3+"7(430(''"7(+*@"+,(+"46"298(+*8"*C*7>"1432+*%

11 / 12
Select display mode
Press the RAIN button several times until the desired time range is displayed:
RATE Current rainfall rate in past hour
HOUR Total rainfall rate for current hour
DAY Total rainfall rate within the current day, from midnight
WEEK Total rainfall rate for current week
MONTH Total rainfall rate for current month
YEAR Total rainfall rate for within a year (from first day of the year)
The measurement unit (millimeter or inch) for rainfall is selected via the MM / IN sliding switch.
14 Total Rainfall SINCE function
1. Press the SINCE button to display the total rainfall from a customized point in time.
2. To delete the current data: Press and hold the SINCE button until the stored value is cleared. The
new value is now equal to day rainfall and the base unit will start again to collect the rainfall data.
15 Technical data
Main unit
Batteries 2x AA, 1.5 V
Temperature unit °C / °F
Temperature measuring range 14°F - 122°F
Humidity measuring range 20% - 90%
Time display HH:MM / Weekday
Time format 12 or 24 hours
Calendar display MM/DD/YR (Default setting) or DD/MM/YR
Dimensions 95 x 155 x 23 mm (W x H x D)
Weight 212 g (without batteries)
Wireless Rain gauge sensor
Batteries 4x AA, 1.5 V
Transmission frequency 915 MHz
Maximum radio-frequency power < 25mW
Temperature unit °C / °F
Temperature measuring range -40°F – 140°F
Rainfall unit mm, inch
Rainfall measuring range 0 – 29999 mm
Time signal
Time zone
Weight
Dimensions
WWVB
PST, MST, CST, EST, AST, NST
109 x 200 x 109 min(W x H x D)
372g without batteries

12 / 12
16 Disposal
Sort packaging into different materials for disposal. Contact the local waste disposal service
provider or environmental agency for information about appropriate waste management.
Do not dispose of electronic devices in the household garbage!
As per Directive 2012/19/EC of the European Parliament on waste electrical and electronic
equipment and its adaptation into German law, used electronic devices must be collected
separately and recycled in an environmentally friendly manner.
Do not dispose of batteries and rechargeable batteries with the household waste. You are
legally required to return used batteries and rechargeable batteries. After they are used, the
batteries can be returned free of charge to our point of sale or to a nearby location (for exa-
mple, retailers or municipal collecting points).
Batteries and rechargeable batteries are marked with a symbol of a crossed-out dustbin and
the chemical symbol of the pollutant. “Cd” stands for Cadmium, “Hg” stands for mercury and
“Pb” stands for lead.
17 FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interferenceto radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be det-
ermined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC responsible party: Explore Scientific, LLC
Company name: Explore Scientific, LLC
Address: 1010 S. 48th Street, Springdale, AR 72762
Phone: [phone]