Brickcom WAP-350N User manual

1
WAP-350N
User’s Manual
Quality Service Group

2
Product Name: WAP-350N
Release Date: 2012/01
Manual Revision: V1.0
Web Site: www.brickcom.com
Email: [e-mail]
[email protected]

3
Table of Contents
Introduction ........................................................................................................................ 1
Planning Your Wireless Network ........................................................................................ 2
Example of a Simple Wireless Network ............................................................... 4
Connecting the WAP-350N Access Point to the Network .................................... 6
Setting Up the WAP-350N Wireless-N Access Point ......................................................... 7
Launching the Web-Based Configuration Utility .................................................. 7
Navigating the Utility............................................................................................ 7
Getting Started ................................................................................................................... 8
Status and Statistics........................................................................................................... 9
Checking System Summary ................................................................................ 9
Checking Interface Statistics.............................................................................. 10
Checking TCP/UDP Services ............................................................................ 12
Checking View Log ............................................................................................ 13
Checking Associated Clients ............................................................................. 14
Checking Site Survey Scan ............................................................................... 15
General Settings .............................................................................................................. 16
Configuring LAN Settings .................................................................................. 16
Configuring Port Settings................................................................................... 18
Configuring Captive Portal Settings................................................................... 19
Configuring 802.1X Authentication Settings....................................................... 20
Wireless ........................................................................................................................... 21
Configuring Basic Settings................................................................................. 21
Configuring Radio Scheduler............................................................................. 26
Configuring Wi-Fi Protected Setup .................................................................... 26
Configuring Load Balance ................................................................................. 28
Configuring Rogue AP Detection ....................................................................... 29
Configuring Advanced Settings.......................................................................... 30
Configuring WDS Settings ................................................................................. 32
Administration .................................................................................................................. 34
Configuring User Account .................................................................................. 34
Configuring Password Strength ......................................................................... 35
Configuring System Time................................................................................... 37
Upgrading the Firmware .................................................................................... 38
Configuring Download/Backup .......................................................................... 39
Setting DHCP Auto Configuration...................................................................... 39
Configuring System Logs................................................................................... 40
Configuring Email Alert ...................................................................................... 42
Configuring Idle Session Timeout ...................................................................... 43
Rebooting the Access Point............................................................................... 44
Configuring Access Management ...................................................................... 45
Discovering Access Point .................................................................................. 46
Configuring Access Control ............................................................................... 46
Configuring SNMP............................................................................................. 48

1
Introduction
Thank you for choosing the WAP-350N Wireless-N Access Point with Power over Ethernet.
This access point allows you to network wirelessly better than ever. An access point allows for
greater range and mobility within your wireless network while also allowing you to connect the
wireless network to a wired environment. The Wi-Fi Protected Setup (WPS) feature is also
supported to help you simplify the setting up and configure security on a wireless network.
The WAP-350N Wireless-N Access Point with Power over Ethernet even offers the
convenience of Power over Ethernet (PoE) capability, so it can receive data and power over a
single Ethernet network cable.
The WAP-350N Access Point supports the 802.11n Draft 2.0 Specification by IEEE. It also
support 802.11g and 802.11b clients in a mixed environment. This access point can support
802.11n connections, which are much faster than the earlier 802.11b/g technologies. In
addition, this access point provides longer coverage by using multiple antennas to transmit
and receive data streams in different directions. Networks are useful tools for sharing
computer resources. You can access one printer from different computers and access data
located on another computer's hard drive. Networks are even used for playing multiplayer
video games. So, networks are not only useful in homes and offices, they can also be fun.
Computers on a wired network create a LAN, or Local Area Network. They are connected with
Ethernet cables, which is why the network is called “wired.” Computers equipped with
wireless client cards or adapters can communicate without cumbersome cables. By sharing
the same wireless settings within their transmission radius, they form a wireless network.
This is sometimes called a WLAN, or Wireless Local Area Network. The access point bridges
wireless networks of 802.11n, 802.11g and 802.11b standards and wired networks.
Use the instructions in this guide to help you connect the access point, set it up, and configure
it to bridge your different networks. These instructions should be all you need to get the most
out of the access point.

2
Planning Your Wireless Network
Network Topology
A wireless network is a group of computers, each equipped with one or more wireless
adapters. Computers in a wireless network must be configured to share the same radio
channel to talk to each other. Several computers equipped with wireless cards or adapters can
communicate with each other to form an ad-hoc network without the use of an access point.
Brickcom also provides products to allow wireless adapters to access wired network through a
bridge such as the wireless access point, or wireless router. An integrated wireless and wired
network is called an infrastructure network. Each wireless computer in an infrastructure
network can talk to any computer in a wired or wireless network via the access point or
wireless router.
An infrastructure configuration extends the accessibility of a wireless computer to a wired
network, and may double the effective wireless transmission range for two wireless adapter
computers. Since an access point is able to forward data within a network, the effective
transmission range in an infrastructure network may be more than doubled since access point
can transmit signal at higher power to the wireless space.
Roaming
Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that
you can move your wireless computer within your network and the access points will pick up
the wireless computer’s signal, providing that they both share the same wireless network
(SSID) and wireless security settings.
Before you consider roaming, choose a feasible radio channel and optimum access point
position. Proper access point positioning combined with a clear radio signal will greatly
enhance performance.

3
Network Layout
The Wireless-N Access Point has been designed for use with 802.11n, 802.11g and 802.11b
products. The access point is compatible with 802.11n, 802.11g and 802.11b adapters, such
as the notebook adapters for your laptop computers, PCI adapters for your desktop PCs, and
USB adapters for all PCs when you want to enjoy wireless connectivity. These wireless
products can also communicate with a 802.11n, 802.11g or 802.11b wireless print server (if
available).
To link your wired network with your wireless network, connect the access point’s Ethernet
network port to any switch or router with Power over Ethernet (PoE)—or a PoE injector.

4
Example of a Simple Wireless Network
The diagram below shows a typical infrastructure wireless network setup.
The wireless access points are connecting to a switch that provides them with power. Each
access point can connect multiple wireless devices to the network.
This network provides connectivity among wireless network devices and computers that have
a wired connection to the switch.
The switch connects to a router that connects to the Internet.

5
Getting to Know the Wireless-N Access
Point
This chapter describes the external features of the WAP-350N Access Point.
Back Panel
ETHERNET Port—Connects to Ethernet network devices, such as a switch or router that may
or may not support PoE.
Antennas and Positions
The WAP-350N Access Point has two detachable 5dBi internal antennas. These antennas are
located inside the device.
The two antennas support 2x2 “multiple in, multiple out” (MIMO) diversity in wireless-N mode.
Connecting the WAP-350N Access Point
This document describes how to place and connect the WAP-350N Access Point to your
network. Depending on your application, you might want to set up the device first before
mounting it.
Placement Options
You can place the WAP-350N Access Point horizontally on its rubber feet, or mount it on the
wall or ceiling.
Desktop Option
For desktop mounting, place the access point horizontally on a surface so it sits on its four

6
rubber feet.
Connecting the WAP-350N Access Point to the Network
You can connect the WAP-350N Access Point to your network in one of the following ways:
• Using a PoE switch
• Using a PoE injector
Using a PoE Switch to Connect the WAP-350N Access Point to the Network
To connect the WAP-350N Access Point to your network using a PoE switch, simply connect
the Ethernet port of the access point to a PoE port on the PoE switch.
Using a PoE injector to Connect the WAP-350N Access Point to the Network
Use a PoE power injector to connect between WAP-350N Access Point and a non-PoE switch
or PC.

7
Setting Up the WAP-350N Wireless-N Access
Point
The WAP-350N Access Point works right out of the box with the default settings. However, you
can change these settings to suit your needs by accessing the access point using a web-based
configuration utility.
NOTE: Make sure you have Enabled TCP/IP on your computers prior to proceeding.
Computers communicate over the network with this protocol.
Launching the Web-Based Configuration Utility
To configure the WAP-350N Access Point, follow these steps to access the WAP-350N
web-based configuration utility from your computer.
1. Connect your computer to the same network the WAP-350N Access Point is connected to.
2. By default, the WAP-350N Access Point has DHCP client enabled. You can either attached
to the router to get an IP or wait for a while for the Access Point will automatically set it’s IP
address of 192.168.1.250 and a default mask of 255.255.255.0.
3. Launch a web browser, such as Internet Explorer.
4. In the Address field enter 192.168.1.250 and press the Enter key.
5. In the User Name and Password fields enter admin. The default user name and password
is admin.
6. Click Log in.
Navigating the Utility
The web-based utility consists of the following main screens:
• Getting Started
• Status and Statistics
• Setup
• Wireless
• Administration

8
Getting Started
Getting started allows you to configure access point with easy steps.
All the configurations also can be set by accessing into the menu of Setup, Wireless and
Administrator. However, Getting Started is a convenient way to guide the user to set the
access point quickly.

9
Status and Statistics
This section describes how to change the status settings for the access point:
• “Checking System Summary”
• “Checking Interface Statistics”
• “Checking TCP/UDP Services”
• “Checking View Log”
• “Checking Associated Clients”
• “Checking Site Survey Scan”
Checking System Summary
The System Summary page displays the access point’s current status information for the local
network.
To check system information and local network status, follow these steps:
1. Click Status and Statistics > System Summary.
This page displays the status information of your access point:
• System Information
- PID VID—The description of the access point.
- Hardware Version—The version of the access point’s current hardware.
- Firmware Version—The version of the access point’s current software.

10
- Serial Number—The serial number of the access point.
- Host Name—The host name of the access point.
- Model Description—The model information of the access point.
- System Up Time—The length of time the access point has been running.
- System Time—The time the access point starts running.
• Access Management Status
- Telnet Service—Status of Telnet Service
- SSH Service—Status of SSH Service
- HTTP Service—Status of HTTP Service
- HTTPS Service—Status of HTTPS Service
• Local Network
- MAC Address—The MAC address of the access point’s local network interface.
- IP Address—The access point’s IP address as it appears on your local
network.
- Subnet Mask—The access point’s subnet mask.
- Default Gateway —The access point’s default gateway address.
- DNS-1 —The access point’s primary DNS server address.
- DNS-2—The access point’s secondary DNS server address.
2. To update the status information, click Refresh.
Checking Interface Statistics
The Status and Statistics > Interface Statistics page displays the access point’s current status
information for the local network.

11
To check wireless network status, follow these steps:
1. Click Status and Statistics > Interface Statistics.
This page displays the status information of your access point:
• Wired Settings
- Port Operational Status—The physical connection of the access point with the computer.
- Packets Received—The number of packets received.
- Packets Transmitted—The version of the access point’s current software.
- Byte Received (Octets)—The number of bytes received.
- Byte Transmitted (Octets)—The number of bytes transmitted.
- Received Error—The error number of bytes received.
- Transmit Error—The error number of bytes transmitted.
• Wireless Settings
- SSID Name—The Service Set Identifier, or network name. This access point may have
up to four wireless networks, each with a unique SSID.
- Wireless Radio—The status of current wireless radio.
- MAC Address—The MAC address of the wireless radio..
- Mode—The wireless mode used by the network.
- Channel—Channel setting selected on the Basic Wireless Settings screen.
- Security Mode—The wireless security method used by the access point.
- VLAN ID—The VLAN ID for this wireless network.

12
- Packets Transmitted—The number of packets transmitted.
- Byte Received (Octets)—The number of bytes received.
- Byte Transmitted (Octets)—The number of bytes transmitted.
- Received Error—The error number of bytes received.
- Transmit Error—The error number of bytes transmitted.
2. To update the status information, click Refresh.
Checking TCP/UDP Services
The TCP/UDP Services page displays the access point’s current status information for the
local network.
To check TCP/UDP Services status, follow these steps:
1. Click Status and Statistics > TCP/UDP Services.
This page displays the TCP/UDP Services information of your access point:
• TCP Service Table
- Service Name—The name used for the service.
- Type—The protocol used for the service.
- Local IP Address—The IP address of the service.
- Local Port —The local port number of the service.
- Remote IP Address —The remote IP address of the service.
- Remote Port —The remote port number of the service.
- State —The current status (e.g., listen, established) of the service.
• UDP Service Table
- Service Name—The setting configured in Administration > Discovery for the service.
- Type—The protocol used for the service.
- Local IP Address—The IP address of the service.
- Local Port —The local port number of the service.
- Application Instance —The number for the examples of application.
2. To update the status information, click Refresh.

13
Checking View Log
The View Log page displays the access point’s current status information for the local network.
To check View Log status, follow these steps:
1. Click Status and Statistics > View Log.
This page displays the Log information of your access point:
• Select Log type — Choose RAM or FLASH as the log type.
• Rows per page—The number of the records displayed in this page.
• Log Time —The log time recorded of your access point.
• Severity—The local port number of the service.
• Description—The brief explanation of your access point.
2. To update the status information, click Refresh.
3. To clear the status information, click Clear.
4. To export the status information as a file, click Export.

14
Checking Associated Clients
The Associated Clients page displays the associated client’s current status information for the
local network.
To check Associated Clients status, follow these steps:
1. Click Status and Statistics > Associated Clients.
This page displays the Associated Clients information of your access point:
• MAC Address — The MAC Address of the client.
• Channel—The channel used by the client.
• Band —The Radio band used by the client.
• State —The current status of the client.
• TxRate —The data transmitted rate of the client.
• RxRate —The data received rate of the client.
• RSSI —Received signal strength indicator (RSSI) is a measurement of the power
present in a received radio signal.
2. To update the status information, click Refresh.

15
Checking Site Survey Scan
The Site Survey Scan page displays the associated access point current status,
information for the local network.
To check access point status, follow these steps:
1. Click Status and Statistics > Site Survey Scan.
This page displays the Associated access point information:
• MAC Address — The MAC Address of the associated access point.
• SSID Name—The SSID name of the associated access point.
• Channel—The channel of the associated access point.
• Band —The Radio band of the associated access point.
• Security Mode —The security mode of the associated access point.
• RSSI —Received signal strength indicator (RSSI) is a measurement of the power
present in a received radio signal.
2. To update the status information, click Refresh.

16
General Settings
This section describes how to configure the general settings of the access point:
• “Configuring LAN Settings”
• “Configuring Port Settings”
• “Configuring Captive Portal”
• “Configuring 802.1X Authentication”
Configuring LAN Settings
The LAN Settings page displays the general settings of the access point.
To configure the LAN settings of the access point, follow these steps:
1. Click the Configure LAN Settings link.
This page displays the LAN setting information:
2. Configure the LAN settings.
• Basic Setup
- Host Name — Enter the host name of the access point.
You can use the host name to access the web-based configuration utility through the
network if a record of the host name exists in your DNS server. The access point
publishes the host name to your DNS server if you configured the access point to

17
acquire its IP address from a DHCP server. Follow your organization’s policy when
assigning this name.
- Management VLAN ID—Enter the device name for the access point.
This name is identification purposes only. Unique, memorable names are helpful,
especially if you are deploying multiple access points on the same network. This
name helps you identify the access point after you log in.
- Untagged VLAN —Check this box to enable this function.
- Default VLAN ID —Enter the VLAN ID for the access point.
• Network Setup for IPv4
- Connection Type —Select DHCP or Static IP Address as the connection type.
- IP Address—The access point’s IP address as it appears on your local
network.
- Subnet Mask—The access point’s subnet mask.
- Default Gateway —The access point’s default gateway address.
- DNS-1 —The access point’s primary DNS server address.
- DNS-2—The access point’s secondary DNS server address.
• Network Setup for IPv6
- IPv6 Admin Mode — Select Enable to enable IPv6 for your access point.
- Connection Type — Select DHCP or Static IP Address as the connection type.
- Static IPv6 Address—The access point’s IP address as it appears on your local
network.
- Static IPv6 Address Prefix Length— Enter the prefix length for IPv6.
- Default IPv6 Gateway —The access point’s default IPv6 gateway address.
- DNS-1 —The access point’s primary DNS server address.
- DNS-2—The access point’s secondary DNS server address.
3. Click Save.