Brigade LS-60-A Original operating instructions

Installation Guide 4885
LS-60-A
Installation & Operation
Guide
1 Wire Connections
Wire Colour
Vehicle Connection
Black
Power Supply Negative (0V)
Red
Power Supply Positive +12/24Vdc, fused and non permanent
Green
Speed Pulse Input (e. g. tachograph pin no. B8, 4 pulses per meter distance)
Pink
Control of Programming & Reading Modes
Purple
Switch Power Output
Warning: Switch output maximum current is 1.2A. Use a relay if higher current
from switch output for connected devices is required.
2 Normal Operation
Switch Power Output ON state
When the vehicle speed is below the speed threshold setting, the Switch Power Output will be
activated and indicated by the GREEN light.
Switch Power Output OFF state
When the vehicle speed exceeds the current threshold setting, the Switch Power Output will be
deactivated and indicated by the RED light.
3 Displaying or Programming the Speed Threshold
Note: Please read the below instructions before amending the speed threshold.
3.1 Speed Threshold Table
Number of Light Flashes
Selected Speed Threshold
mph
kph
1
0.6
1
2
6
10
3
10
16
4
12
19
5 (default factory setting)
14
23
6
16
26
7
18
29
8
20
32
9
30
48
10
60
97
Note 1:Speed based on four pulses per meter distance.
Note 2:On some Volvo trucks the speed setting may need to be set at half the required speed
e.g. if number 4 is required set to number 2.
Light

21/02/2019 16:23:00
LS-60 (4851)-Installation&Operation Guide - v0.3 ENG draft.docx
3.2 Sequence for Displaying or Programming
1.Power up the unit while vehicle is stationary (no speed pulse present).
2.Hold the pink wire to ground (0V, e. g. to black wire).
3.Immediately release the PINK wire from ground after 3 RED/GREEN light flash cycles (within
less than 2secs).
4.There are then two modes available:
4.1.Enter Display Mode - Used to view current stored speed threshold setting:
(1) After a single GREEN light flash, immediately touch the PINK wire to ground (within
less than 2secs) then 3 RED/GREEN light flash cycles (Within 2 Seconds)
(2) The GREEN light will start to flash. Count the GREEN light flashes and refer to the
table above for the set speed threshold.
(3) Followed by 5 fast GREEN light flashes to confirm the end of the Display Mode.
(4) Return to Normal Operation with constant GREEN light.
4.2.Enter Program Mode - Used to change speed threshold setting:
(1) After a double GREEN light flash, immediately touch the PINK wire to ground (within
less than 2secs).
(2) The GREEN light will start to flash up to 10 times. Immediately touch the PINK wire to
ground once the count has reached the required number corresponding to the desired
speed threshold, see above table.
(3) Followed by 5 fast GREEN light flashes to confirm the end of the Program Mode.
(4) Normal Operation is resumed with constant GREEN light.
(5) It is recommended to check if the selected speed setting is correct via the Display
Mode.
3.3 Further Notes on Display or Program Mode
1. If an input signal (speed pulse) is detected on the GREEN wire (Speed Pulse Input) the
sequence for Displaying or Programming cannot be entered. The vehicle must be stationary.
2. If the correct sequence is not followed for Display or Program Mode the RED light will flash 5
times to indicate an error and Normal Operation will resume with previous setting.
3. After either the Display or Program Modes have finished, the PINK wire must be
disconnected from ground for at least 1sec before next sequence can be started again.
4 Specifications
Speed range
0 to 60mph / 100kmp
Speed pulse calibration
(see also speed Threshold table)
Based on 4 pulses per meter distance
Max. switched power output current
1.2A
Operating voltage range
9Vdc to 32Vdc
Input current
Typ. <0.03A (Switch Power Output off)
Max. <1.8A (Switch Power Output on state)
Polarity
Negative ground
Operating temperature range
-40°C to +85°C
Dimensions (without connector)
44mm x 64mm x 16mm
Weight (including connector tail)
approx. 35g
Vehicle mounting
Housing with opening lugs for fixing e.g. with a cable tie
Plug with cable tail, cable length
300mm +/- 20mm
Approvals: CE, ECE Regulation No. 10 Revision 4 (“E-marking”), FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any change or modifications not expressly approved by the responsible party responsible for
compliance could void the user’s authority to operate the equipment.
Specifications subject to change. Sous réserve de modifications techniques. Änderungen der technischen Daten vorbehalten.
Specifiche soggette a variazioni. Las especificaciones están sujetas a cambios. Wijzigingen in specificaties voorbehouden. As
especificações estão sujeitas a alterações. Спецификация может изменяться.
Brigade
Electronics
LS-60 / LS-XXXX