Britex DPDF User manual

MELBOURNE
Britex Place Mirra Crt
Bundoora VIC 3083
t(03) 9466 9000
e[email protected]om.au
SYDNEY
16 Northumberland Drv
Taren Point NSW 2229
t(02) 9531 2100
[e-mail]
PERTH
Unit 1/8 Principal Link
Malaga WA 6090
t(08) 9249 5464
[e-mail]
BRISBANE
19 Manilla St
East Brisbane QLD 4169
t(07) 3363 2400
e[email protected]om.au
ADELAIDE
The Britex Group
SA State Office
t1300 764 744
e[email protected]om.au
Installation
Guide
375
155 820
200
975
AA
14
120
200
SECTION A-A
DPDF
A3
SHEET 1 OF 3
SCALE:1:7
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
db
09/09/16
B
SD-2862.1
Sign
Date
Approval For Manufacture
DPDF
Pedestal Drinking Fountain
Drinking Fountain
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023

Australia’s Finest Stainless | britex.com.au
About
Preparation and Completion Notes
The BRITEX Stainless Steel Pedestal Drinking Fountain is supplied complete with a heavy-
duty push button Drink Safe™ low lead bubbler and waste outlet. A service hatch in the
pedestal provides access for installation and maintenance requirements. Manufactured
from 1.6mm commercial grade 304 stainless steel the Pedestal Drinking Fountain is
secured to the ground below with a fixing plate within the pedestal and suitable for
schools, parks and sporting clubs.
Contractors please note: Ideally, stainless steel drinking fountain should be installed after all
other building activities that could cause contamination to the surface of the stainless steel
have been completed.
These activities include:
Using proprietary building mortar removers containing hydrochloric acid. Welding, cutting and
grinding that may ‘spray’ carbon steel and iron particles onto the stainless-steel surface.
1. Remove drinking fountain from box packaging and inspect for any damage before beginning
installation process.
2. Confirm all requested details are correct.
3. If drinking fountain is damaged in transit or if any details are not as requested, do not install
it. Notify Britex immediately within 24 hours of receipting the product.
2
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORISED SERVICE PERSON
Installation of this unit must be in accordance with AS/NZS 3500.1, AS/NZS 3500.2, the PCA
and the local regulatory requirements. Water and/or electrical supply conditions must comply to
national or state requirements and standards. Failure to comply shall void the product warranty
and may affect the performance of the product. For further support and after-sales care, please
contact Britex.
WARNING
WHEN INSTALLATION IS COMPLETE, ENSURE THESE INSTRUCTIONS REMAIN INSIDE
THE PLASTIC BAG PROVIDED WITH THE UNIT FOR FUTURE REFERENCE

Australia’s Finest Stainless | britex.com.au 3
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023
DPDF Installation Drawing
Access Panel
Access Panel
Fixing holes
Services Access
23
40mm Waste
99-16-0010
Pressing
160
Access Panel
120
100
75
Prepare hole in floor for unit fixing and services
connection.
4 x 14mm bolts at 160mm spacing to fix unit at the base
Please connect the following services via a licensed
plumber who is certified in PCA, AS3500.1 and AS3500.2
Mains water to 1/2" BSP inlet via services access.
Waste water piping to 40mm waste outlet via services
access.
50-07-0016
DPDF Installation Drawing
A3
SHEET 4 OF 5
SCALE:1:7
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
DS
28/09/23
A
SD-2862.4
Access Panel
Access Panel
Fixing holes
Services Access
23
40mm Waste
99-16-0010
Pressing
160
Access Panel
120
100
75
Prepare hole in floor for unit fixing and services
connection.
4 x 14mm bolts at 160mm spacing to fix unit at the base
Please connect the following services via a licensed
plumber who is certified in PCA, AS3500.1 and AS3500.2
Mains water to 1/2" BSP inlet via services access.
Waste water piping to 40mm waste outlet via services
access.
50-07-0016
DPDF Installation Drawing
A3
SHEET 4 OF 5
SCALE:1:7
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
DS
28/09/23
A
SD-2862.4
Access Panel
Access Panel
Fixing holes
Services Access
23
40mm Waste
99-16-0010
Pressing
160
Access Panel
120
100
75
Prepare hole in floor for unit fixing and services
connection.
4 x 14mm bolts at 160mm spacing to fix unit at the base
Please connect the following services via a licensed
plumber who is certified in PCA, AS3500.1 and AS3500.2
Mains water to 1/2" BSP inlet via services access.
Waste water piping to 40mm waste outlet via services
access.
50-07-0016
DPDF Installation Drawing
A3
SHEET 4 OF 5
SCALE:1:7
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
DS
28/09/23
A
SD-2862.4

Australia’s Finest Stainless | britex.com.au
Installation Instructions
1. The box should have the product that is pre-plumbed ready to be mounted to the
ground.
2. Prepare the area in which the DPDF will be mounted too, there will need to be mains
pressure accessible to the unit. A waste outlet will need to be run underground as well.
3. Once all the waste and mains are run underground to the drinking fountain then drill out
the holes in the right position, Britex suggests you use 4 x 14 mm bolts at 160mm spacing
to fix the unit at the base to the ground, these are not supplied. Ensure these are tightened
according.
4. Pull off the access panel plates on the side of the drinking fountain and ensure the
waste and bubbler are plumbed up according to the PCA or relevant Australian Plumbing
Standard.
5. Once that is done the access panels can be reinstalled and the unit can be checked to
see it is working to the desired degree.
4
Technical Parameters
Inlet Connection 1/2” BSP Male
Recommended Inlet Pressure 350 kPa
Maximum Inlet Pressure 500 kPa
Water Supply Temperature
Limitations Min 5; Max 60°C
Nominal Flow Rate (LPM) 1.95
Finish Chrome
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023

Australia’s Finest Stainless | britex.com.au 5
Troubleshooting
PROBLEM CAUSES ACTION
No Water Water is turned off Turn on water
Leaking waste pipe Crack in pipe Call a plumber to fix the issue
Inconsistent flow Blocked top assembly Remove top assembly and clean
Button hard to press The mains pressure may be
too great
Reduce to below 500kPa
(70PSI).
Spare Parts
TW-CPB
Bubbler Chrome Plated (Low Lead Brass) Drink Safe with Metal
Mouth Guard
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023

Australia’s Finest Stainless | britex.com.au
Care and Maintenance
Stainless steel products should be kept clean at all times. The secret to stainless steel’s
ability to maintain a high-quality finish and promises of a long-life expectancy is the
invisible chromium-oxide film that sits on the surface and protects the steel beneath. To
maintain this film, it is essential that the surface remains clean and in constant contact
with oxygen. If this film is penetrated (either by abrasion or chemically) and dirt, liquid,
grime contaminants embed themselves in these micro chasms for an extended period,
the chromium oxide film will not be able to regenerate and the steel below will eventually
become damaged and discoloured.
What we recommend for general cleaning and maintenance:
Cleaning Materials:
• A soft cloth
• A soft-bristled brush
• A natural or artificial sponge
Cleaning Solutions:
• Hand washing soap / soft water solution
• Mild soap / soft water solution
White vinegar / soft water solution
It is recommended that general cleaning of stainless-steel surfaces be carried out weekly, or
as soon as a build-up of surface media has been observed. To clean, simply wash stainless
steel surfaces with, warm, diluted, mild soapy water using a cloth or soft bristled brush. Once
all dirt, oil and grime is removed, rinse thoroughly with clean water and wipe dry.
6
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023

Australia’s Finest Stainless | britex.com.au
Warranty
The BRITEX product is backed by our manufacturer’s warranty available for download
from our website at www.britex.com.au. We expressly warrant that the product is free from
operational defects in workmanship and materials for the warranty period indicated on the
schedule in the manufacturer’s warranty. During the warranty period, BRITEX will repair or
replace any defective products manufactured by BRITEX at no charge, provided that the
terms of the manufacturer’s warranty are followed.
This warranty is the only warranty given by BRITEX, and we expressly disclaim all other
warranties, including but not limited to implied warranties of merchantability and fitness
for a particular purpose. This warranty represents the sole and exclusive remedy for breach
of warranty, and BRITEX shall not be liable for any incidental, special, or consequential
damages, including lost profits, labor charges, delays, vandalism, negligence, fouling
caused by foreign material, damage from adverse water conditions, chemical, electrical or
any other circumstances beyond BRITEX’s control.
This warranty shall be void if the product is abused, misused, improperly installed,
maintained, or altered. By purchasing our product, you agree to these terms and
conditions. We appreciate your business and look forward to providing you with high-
quality products and services.
7
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023

MELBOURNE
Britex Place Mirra Crt
Bundoora VIC 3083
t(03) 9466 9000
e[email protected]om.au
SYDNEY
16 Northumberland Drv
Taren Point NSW 2229
t(02) 9531 2100
[e-mail]
PERTH
Unit 1/8 Principal Link
Malaga WA 6090
t(08) 9249 5464
[e-mail]
BRISBANE
19 Manilla St
East Brisbane QLD 4169
t(07) 3363 2400
e[email protected]om.au
ADELAIDE
The Britex Group
SA State Office
t1300 764 744
e[email protected]om.au
DPDF Installation Guide | QID 2.2 | Rev 2 | 9 Oct 2023